Effects of vasodilators and perfusion pressure on coronary flow and simultaneous release of nitric oxide from guinea pig isolated hearts

OBJECTIVE: The aims were to validate the use of a direct reading NO electrode, to compare the effects of diverse acting drugs on altering coronary flow (CF) and NO release, and to examine the effects of altered perfusion pressure on flow-induced changes in NO concentration [NO] in the hemoglobin free effluent of guinea pig isolated hearts. METHODS: Hearts were isolated and perfused initially at a constant perfusion pressure (55 mmHg) with a modified Krebs-Ringer's solution equilibrated with 97% O2 and 3% CO2 at 37 degrees C. Heart rate, left ventricular pressure, CF, and effluent pH, pCO2, pO2, and NO generated current were monitored continuously on-line. Effluent was sampled for L-citrulline. Percent O2 extraction and O2 consumption were calculated. [NO] was quantitated with a sensitive amperometric sensor (sensitivity > or = 1 nmol/l approximately 3 pA) and a selective gas permeable membrane. RESULTS: The electrode was not sensitive to changes in solution pO2, flow, or pressure. The electrode was sensitive to pCO2 (-0.50 nmol/l/mmHg) and temperature (+24.5 nmol/l/degree C), so coronary effluent pCO2 was measured to compensate for a small decrease in pCO2 that occurred with an increase in coronary flow, and effluent temperature was rigidly controlled. Serotonin, bradykinin, and nitroprusside increased NO release along with CF, whereas nifedipine, butanedione monoxime, zaprinast, and bimakalim comparably increased CF but did not increase [NO] or NO release. Increases in CF (ml/g/min) and NO release (pmol/g/min), respectively, were 5.0 +/- 1 and 100 +/- 17 for 1 mumol/l serotonin, 7.5 +/- 1 and 148 +/- 18 for 100 nmol/l bradykinin, and 7.8 +/- 1 and 173 +/- 28 for 100 mumol/l nitroprusside. The increases in effluent NO by bradykinin were proportional to the increases in L-citrulline. Tetraethylammonium decreased CF, but did not change NO release, indomethacin changed neither CF nor NO release, and NG-nitro-L-arginine methyl ester (L-NAME) reduced CF by 2.6 +/- 1 ml/g/min and NO release by 25 +/- 8 pmol/g/min. An increase of CF of 8.0 +/- 0.3 ml/g/min, produced by increasing perfusion pressure from 25 to 90 mmHg, increased [NO] by 30 +/- 4 nmol/l; L-NAME but did not reduce the pressure-induced increase in CF, but reduced the increase in [NO] to 10 +/- 5 nmol/l. CONCLUSIONS: This study demonstrates in intact hearts real-time release of NO by several vasodilator drugs and by pressure-induced increases in flow (shear stress) and attenuation of these effects by L-NAME.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Fracture toughness evaluation of adjacent flow weld line in polystyrene by the SENB method

Fracture toughness of adjacent flow weld lines, defined as weld lines that occur when two flow fronts meet and continue to flow together in the same direction (meld line or hot weld line), was evaluated by the single‐edge notched‐bend (SENB) method using three differently‐shaped obstructive pins. Although the fracture toughness varied depending upon the shapes of the pin, the values could be standardized as the distance from the meeting point of the two flow fronts flowing around the pin. The fracture toughness decreased drastically from the meeting point along the weld line and then slightly increased. These characteristic features could be explained by flow‐induced molecular orientation at the weld line interface. The molecules around the meeting point that were initially oriented parallel to the weld line due to fountain flow were able to relax, and then entanglement across the weld line interface developed because the flow stopped in the middle of the filling process, resulting in high fracture toughness. In contrast, the material at the downstream side of the weld line continued flowing during the filling process, being stretched along the flow direction. So, the molecular orientation at this area could not relax. In addition, the V‐notch shape, i.e., the depth and length at the surface of the weld line, which also varied depending on the shape of the obstacles, was considered to be identical when the meeting point was allowed to be a datum point. Thus, the meeting point was found to be a significant factor when the properties of weld lines are investigated. POLYM. ENG. SCI., 45:1059–1066, 2005. © 2005 Society of Plastics Engineers     

Radiation detector made of a high-quality polycrystalline diamond

Radiation detector was made of a high-quality CVD polycrystalline diamond composed of frost column like structure diamond grains, and induced charge distribution spectra and drift velocities were measured by using alpha particles. As a result, the CVD polycrystalline achieved maximum induced charge of 83% of HP/HT type IIa diamond. Moreover, the CVD crystal had lower charge loss on electrons compared with the HP/HT type IIa diamond. Drift velocities of electrons and holes were v_e = 7.7 × 10⁴ and v_h = 7.3 × 10⁴cm/s at an electric field of 20 kV/cm, respectively. In addition, response function measurement for 14 MeV neutrons was carried out.     

Effectiveness of spatial representation in the formation of network communities: experimental study on community organizer

In this paper, we present and discuss Community Organizer, a system designed to support network communities. The main characteristic of Community Organizer is the use of spatial representations for the relationships among community members including the communications exchanged among these members. These spatial representations reflect the degree of closeness of interests and concerns among the members, and are intended to provide users with clues on how to form network communities. In order to investigate the effectiveness of the proposed spatial representations, we conducted experiments with two different versions of the software. One version offered meaningful spatial representations while the other version did not. The subjects who used the former software version felt a greater sense of ‘community’, enjoyed using the software more, and actively used it longer than the subjects using the latter software version (control condition). These results indicated that the proposed spatial representations are effective in supporting network community formation.     

Sputter deposition technology as a materials engineering

Sputter deposition is currently being widely used in the microelectronics industry for the production of silicon integrated circuits. Recently interest has been focused on sputter deposition as a new materials processing technique. The highly energetic sputtered atoms enhance crystal growth and/or sintering during film growth. This results in lowering of the growth temperature of high temperature materials including cubic diamonds. Single crystals of complex ceramics materials could be prepared by sputter deposition through epitaxial growth process. Atomically controlled deposition using multi-target sputter enables to make man-made superlattice including high-T _C superconductors of layered perovskite. At present sputter deposition is one of key materials technologies for the coming century.     

A floating-gate analog memory device for neural networks

A floating-gate MOSFET device that can be used as a precision analog memory for neural network LSIs is described. This device has two floating gates. One is a charge-injection gate with a Fowler-Nordheim tunnel junction, and the other is a charge-storage gate that operates as a MOSFET floating gate. The gates are connected by high resistance, and the charge-injection gate is small so that its capacitance is much less than that of the charge-storage gate. By applying control pulses to the charge-injection gate, it is possible to charge and discharge the MOSFET floating gate in order to modify the MOSFET current with high resolution over 10 b. The charge injection can be carried out without disturbing the MOSFET output current with high voltage control pulses. This device is useful for on-chip learning in analog neural network LSIs