Ruthenium dye-sensitized SnO2/TiO2 coupled solar cells

The photoelectrochemical behaviors of RuL₂(NCS)₂ dye-sensitized SnO₂/TiO₂ coupled solar cell was studied and compared with TiO₂ single system. The coupled system shows higher incident photon-to-current conversion efficiency (IPCE) value than the single system. A maximum IPCE value in the coupled system with 3.5 μm-thick SnO₂ and 7 μm-thick TiO₂ attained 82.4% at 530 nm wavelength. The higher IPCE value in the coupled system is attributed to the charge separation by fast electron transfer process from the excited RuL₂(NCS)₂ dye to TiO₂ to SnO₂ in the system with different energy level.     

New fault locating system for air-insulated substations usingoptical current detector

The authors present the basic philosophy, construction, design features, and test results of a new fault locating system. This fault locating system helps to shorten the time required for restoration of service after the occurrence of a busbar fault in an air-insulated distribution substation. Recent optical and electronic technologies allow the design of a highly accurate and compact fault locating system which consists of optical current detectors using the Faraday effect and a fault locating processor using a digital data processing technique. The fault location is carried out by discriminating between the directions of zero-sequence currents. Through various tests and field operations, it has been confirmed that the system has sufficient performance for practical applications     

Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

Partial scan design and test sequence generation based on reduced scan shift method

This paper presents a partial scan algorithm, calledPARES (PartialscanAlgorithm based onREduced Scan shift), for designing partial scan circuits. PARES is based on the reduced scan shift that has been previously proposed for generating short test sequences for full scan circuits. In the reduced scan shift method, one determines proch FFs must be controlled and observed for each test vector. According to the results of similar analysis, PARES selects these FFs that must be controlled or observed for a large number of test vectors, as scanned FFs. Short test sequences are generated by reducing scan shift operations using a static test compaction method. To minimize the loss of fault coverage, the order of test vectors is so determined that the unscanned FFs are in the state required by the next test vector. If there are any faults undetected yet by a test sequence derived from the test vectors, then PARES uses a sequential circuit test generator to detect the faults. Experimental results for ISCAS'89 benchmark circuits are given to demonstrate the effectiveness of PARES.     

An abnormally shortened fatigue life of steels caused by anelasticity

Some abnormal fatigue life shortenings dependent upon load frequency for several steels are discussed. A possible relation between anelasticity caused by interstitial atoms and the abnormal fatigue life drop is presented. Normally, interstitial atoms are in a position which minimizes the energy around a dislocation, the Snoek ordering sites. We consider the Snoek effect as a typical example of anelasticity, and the possibility on atoms moving from attractive sites to repulsive ones when repeated stresses are applied and discuss a theory to explain the reduction of the fatigue life using Snoek ordered atoms moving out by fatigue stress at the frequency of Snoek effect. Bending fatigue tests were conducted to obtain the relationship between fatigue life and load frequency at two different temperatures (298 K and 333 K) for an iron nitrided steel. A sharp fatigue life drop was observed at a load frequency corresponding to the resonant frequency of the Snoek effect for nitrogen atoms. The frequency was about 3 Hz and 298 K and shifted to a higher frequency — about 6 Hz — at 333 K. Results reveal that the possible explanation to those abnormal phenomena may be anelasticity.Work partially conducted at Laboratorio E and Departamento de Ciencias de Materiales, Universidad Simón Bolívar, Venezuela.     

Effect of Grain Boundaries on Thermal Conductivity of Silicon Carbide Ceramic at 5 to 1300 K

The thermal conductivity of a SiC ceramic was measured as 270 W·m⁻¹·K⁻¹ at room temperature. At low temperatures ( T < 25 K), the decrease in the conductivity was proportional to T ³ on a logarithmic scale, which indicated that the conductivity was controlled by boundaries. The calculated phonon mean free path in the ceramic increased with decreased temperature, but was limited to ∼4 μm, a length almost equal to the grain size, at temperatures below 30 K. We concluded that the thermal conductivity of the ceramic below 30 K was influenced significantly by grain boundaries and grain junctions.     

Proposed Phenomenological PTCR Model and Accompanying Phenomenological PTCR Chart

The positive temperature coefficient of resistivity (PTCR) behavior of semiconductive BaTiO₃ is well explained by the Heywang model, which predicts the resistivity behavior above the Curie point based on the acceptor state density at the grain boundaries, the charge carrier density, and the energy gap, E _s, between the conduction band and the acceptor levels. However, the relationship between these parameters and the production parameters (sintering time, composition, and cooling rate) is not well understood. Recently, the present authors have found that E _s can be increased by thorough oxidation. This increase is attributed to a change in the oxidation state of the acceptor. Based on this finding and results from the literature, a phenomenological PTCR model and an accompanying PTCR chart for acceptor–donor-codoped BaTiO₃ are proposed to clarify this relationship. The PTCR chart clarifies that acceptor dopant concentrations, oxidation time, and oxygen partial pressure during oxidation or cooling can be optimized simultaneously to obtain optical PTCR properties.     

Experimental Evaluation of the Acceptor-States Compensation in Positive-Temperature-Coefficient-Type Barium Titanate

Experimental evidence shows that the acceptor-state levels in Sb-doped positive-temperature-coefficient-type BaTiO₃ are compensated up to a critical acceptor-state density. Using the slope of the natural logarithm of the resistivity with respect to 1/ T , instead of maximum resistivity as a measure for the acceptor-state density, it is possible to estimate this critical value. The value obtained (4.2 × 10¹⁷ m⁻²) is believed to be the first reported estimate based on experimental data. It is in good agreement with the estimate of 6 × 10¹⁷ m⁻² (first reported by Jonker) obtained from the spontaneous polarization of BaTiO₃. This shows that the ferroelectric behavior of BaTiO₃ is indeed a feasible explanation for the low resistivity below the Curie point, as proposed by Jonker.     

Rubber-modified epoxy resins containing high functionality acrylic elastomers

The effect of the functionality of n-butylacrylate/acrylic acid copolymers upon the impact resistance of epoxy resins modified with these rubbery copolymers as a second phase was investigated using a high speed tensile test and scanning electron microscopy. It was found that an optimum functionality of copolymer existed for maximum impact resistance. This optimum value was the result of the competition between the amount of rubber–matrix reaction, an increases in which tended to increase toughness, and solubility of the rubber in the epoxy matrix, which eventually decreased toughness.