Economic Model to Optimize Underground Utility Protection

The need for better protecting our vital infrastructure from being damaged or destroyed has received increased attention since the terrorist attacks on September 11, 2001. The tragedy of having thousands of innocent people die before the eyes of an entire nation awakened people to the reality of “managed” attacks of unthinkable magnitudes. However, tragedies of a smaller scale are a daily occurrence but accepted as “collateral damage” of work in an unsafe environment. This paper presents a cost-benefit analysis to address the question of how much money should be spent in protecting underground utilities from damage. During the study of an actual incident it was found that the total costs of such accidents are vastly underreported because only costs for emergency responses and repair are tallied up. This paper makes the case that a comprehensive approach for assessing the total economic impact of such incidents on the public, business, and government is the critical stepping stone to a mathematical optimization of expenditure for damage prevention. In addition, the reader will quickly realize that the use of the presented optimization model provides theoretical underpinning for the engineering profession in its effort to better protect our critical infrastructure from terrorist attacks.     

Use of Explosives on The Moon

The utilization of explosives for excavation on the lunar surface is under serious consideration as a part of the design for construction of temporary and permanent bases. An excavation research program has shown that small‐scale explosives blasting in a lunar‐soil simulant will greatly reduce the digging forces required for scoop and dragline excavators. Some crater‐blasting parameters were determined for the lunar soil simulant at one Earth gravity and at 10 Earth gravities using a centrifuge. The size of the craters produced at 10 Earth gs matched those formed at one earth g by scaling according to the weight of the explosive. These data can be applied to explosive‐excavation problems such as habitat construction, burial of nuclear power sources, and the rapid construction of shelters remote from the main base to shield against solar‐flare activity.     

Diamantartige Kohlenstoffschichten steigern die Effizienz

Diamond‐like carbon thin films enhance efficiency — laser arc deposition of ta‐C Rising prices for fossil fuels as well as the increasing effects of the climate change due to the emission of greenhouse gases reveal the necessity of saving energy. Low friction coatings have an enormous potential in saving energy. Carbon based coatings — named as DLC coatings — are especially well suited for low friction coatings. In particular hydrogen‐free tetrahedral amorphous carbon (ta‐C) coatings are of great interest due to their extraordinary low wear properties. In addition they show excellent low friction properties and especially in combination with specific lubricants the so‐called super low friction effect. For the deposition of ta‐C coatings PVD methods have to be applied instead of CVD methods as it is the case for conventional DLC coatings. We have developed a deposition method which is based on a pulsed arc steered by a laser (Laser‐Arc). This allows us to use large cathodes resulting in a high long‐term stability. Furthermore, the carbon plasma source can be combined with a filtering unit removing almost all droplets and particles, which usually are characteristic for an arc process. The resulting Laser‐Arc source allows for the deposition of smooth and virtually defect‐free ta‐C coatings with a competitive deposition rate.     

Improved thin film stability of differently formulated,printed, and crosslinked polymer layers against successive solvent printing

Interface control remains a top challenge of solution-processed organic light emitting diodes (OLED) stacks since the device performance heavily relies on it. Film stability of an inkjet deposited and crosslinked layer against subsequent exposure to a suitable inkjet printed solvent has been investigated. Impact of processing solvent (solvent used to prepare the polymer layer) on solution-cast thin film properties has already been shown for polymer films. To our knowledge, this study is the first one analyzing thin films stability against solvent exposure using technology relevant materials processed via inkjet printing (IJP). The outcome of this research showed that the stability of the crosslinked films is affected by the solvent used for ink formulation. These findings are of great interest for multilayered semiconductors devices, such as OLEDs, field-effect transistors and dye-sensitized solar cells. Differential scanning calorimetry (DSC) was used to quantify the efficiency of the polymer crosslinking reaction in pure powder and in thin films, as processed from different solvents. Crosslinking efficiency measured by DSC correlated well with the deformation induced by the solvent and observed on layer surfaces. The interaction in solution between polymer and solvent has also been evaluated to explain its impact on thin film stability against successive solvent printing. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48895.     

Neutronic characterization of the MEGAPIE target

The MEGAPIE project aimed to design, build and operate a liquid metal spallation neutron target of about 1 MW beam power in the SINQ facility at the Paul Scherrer Institut (Villigen, Switzerland). This project is an important step in the roadmap towards the demonstration of the accelerator driven system (ADS) concept and high power liquid metal targets in general. Following the design phase, an experimental program was defined to provide a complete characterization of the facility by performing a “mapping” of the neutron flux at different points, from the center of the target to the beam lines. The neutronic performance of the target was studied using different experimental techniques with the goals of validating the Monte Carlo codes used in the design of the target; additionally, the performance was compared with the solid lead targets used before and after the MEGAPIE experiment.     

Ferroelectric Poling of Methylammonium Lead Iodide Thin Films

Seemingly contradictory reports on polar domains and their origin have surrounded the controversial discussion about the ferroelectricity of the methyl ammonium lead iodide (MAPbI₃) thin films that are commonly employed in perovskite solar cells. In this work, microscopic modulations of the polar domain patterns upon application of an electric poling field are correlated with macroscopic changes to the currents through the MAPbI₃ layer. Piezoresponse force microscopy is used to monitor the widening, narrowing, generation or extinction of polar domains, as well as shifts of the domain walls at room temperature under an in‐plane electric poling field that is applied between two laterally organized electrodes. This poling leads to a net polarization of individual grains and the thin film itself. Macroscopically, this net polarization results in a persistent shift of the diode characteristics that is measured across the channel between the electrodes. Both the modulation of the polar domains upon electric poling and the concurrent persistent shift of the electric currents through the device are the unambiguous hallmarks of ferroelectricity, which demonstrate that MAPbI₃ is a ferroelectric semiconductor.     

Mechanistic Insights into Cyclic Peptide Generation by DnaE Split-Inteins through Quantitative and Structural Investigation

Inteins carry out protein-splicing reactions, which are used in protein chemistry, protein engineering and biotechnological applications. Rearrangement of the order of the domains in split-inteins results in head-to-tail cyclisation of the target sequence, which can be used for genetic encoding and expression of libraries of cyclic peptides (CPs). The efficiency of the splicing reaction depends on the target sequence. Here we used mass spectrometry to assess in vivo cyclic peptide formation from different hexameric target sequences by the DnaE split-inteins from Synechocystis sp. and Nostoc punctiforme, revealing a strong impact of the target sequence and of the intein on the intracellular peptide concentration. Furthermore, we determined the crystal structures of their pre-splicing complexes, which allowed us to identify F-block Asp17 as crucial for the DnaE-mediated splicing reaction.     

Adaptive Control for Robotic Rebar Bending

Abstract: Computers are becoming essential tools for integrating design, planning, fabrication, and construction. Computer-controlled construction equipment is poised to receive information from data generated in the design phase. The robotic execution of construction operations, however, depends on complex models for autonomous and intelligent control. This paper introduces a strategy for the robotic bending of rebar and presents the results of experimental work with an actual testing facility. Mechanical properties and behavior of rebar are examined to develop rules for control. Focus is placed on exploring the dynamics between the bender and steel bars. The concepts of impedance, admittance, and compliance of both the machine and the environment will be discussed in the context of control strategy development.