Synthesis and characterization of biocompatible hydroxyapatite coated ferrite

Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own but is stabilized with small substitution of La. Hexaferrite of chemical composition (CaO)_0.75(La₂0₃)_0.20(Fe₂O₃)₆ was prepared using citrate gel method. Hydroxyapatite was prepared by precipitating it from aqueous solution of Ca(NO₃)₂ and (NH₄)₂HPO₄ maintaining pH above 11. Four different methods were used for coating of hydroxyapatite on ferrite particles. SEM with EDX and X-ray diffraction analysis shows clear evidence of coating of hydroxyapatite on ferrite particles. These coated ferrite particles exhibited coercive field up to 2 kOe, which could be made useful for hysteresis heating in hyperthermia. Studies by culturing BHK-21 cells and WBC over the samples show evidence of biocompatibility. SEM micrographs and cell counts give clear indication of cell growth on the surface of the sample. Finally coated ferrite particle was implanted in Kasaulli mouse to test its biocompatibility. The magnetic properties and biocompatibility studies show that these hydroxyapatite coated ferrites could be useful for hyperthermia.     

On the linear correlation between microhardness and mechanical properties in polar polymers and blends

The tensile elastic modulus (E), yield stress (σ_Y) and microhardness (MH) of neat and binary and ternary blends of glassy semicrystalline ethylene–vinyl alcohol copolymer (EVOH), a glassy amorphous polyamide and a semicrystalline nylon‐containing ionomer covering a broad range of properties were examined. The tests were carried out on dry and water‐equilibrated samples to produce stiffer and softer materials, respectively. From the results, more accurate linear correlations were found to describe adequately the microhardness, modulus and yield stress of these strongly self‐associated polymers through hydrogen bonding. Copyright © 2003 Society of Chemical Industry     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

Value of information in remanufacturing complex products

Remanufacturing facilities usually face a trade-off between limited information about remanufacturing yields and potentially long supplier lead times. To improve production performance, these firms may attempt to acquire more timely and accurate information about remanufacturing yields or alternatively, to reduce the lead times of purchased parts. We develop four decision-making models to evaluate the impact of yield information and supplier lead time on manufacturing costs. We identify the operating conditions under which these capabilities are valuable, along with their relative impact on facility performance. Each model is formulated as an infinite horizon, stochastic dynamic program (Markov decision process). Our results indicate that the yield information is generally quite valuable, while investments in supplier responsiveness provide trivial returns to products with few parts. However, as product complexity increases with large number of target parts, the value of short lead times increases.     

Application of novel extractants for actinide(III)/ lanthanide(III) separation in hollow-fibre modules

Separation tests using hollow-fibre modules were performed for the difficult selective extraction of trivalent actinides over fission lanthanides from acidic media. This article shows that with 2,6-di(5,6-dipropyl-1,2,4-triazin-3-yl)pyridine as the extractant, up to 94% americium could be extracted from 1.0 kmol/m³ HNO₃, with minimal lanthanide co-extraction. Using a synergistic mixture of bis(chlorophenyl)dithiophosphinic acid and tri-n-octyl phosphine oxide, tests were performed on extraction, lanthanide scrubbing and stripping. In the extraction test, up to 99.99% americium could be extracted from 0.5 kmol/m³ HNO₃, with approximately one third of the lanthanides being co-extracted. Mass transfer calculations using a consistent set of input data showed good agreement with the experiments.     

Morphological changes induced by colchicine in the chick optic cup in early stages of development. A stereological study

In this study chick embryo optic cups at HH stage 13 of development were analyzed under normal conditions and after inoculation with colchicine for 1, 2, 4, and 8 h. Several changes were seen after these periods of treatment: 1) modifications of the structure, with thicker regions in the cup and a general decrease in the total volume according to the duration of exposure to the drug (about 4 times less than normal, 5,035 x 10(3) microns 3 vs 1,334 x 10(3) microns 3 after 8 h of treatment); 2) enlargement of the ventricular cavity and its closure, due to failure of approximation of retinal and pigmentary layers; 3) failure of lens development, with delay and impairment of pit formation and deformation of all structures; lens volume was less than normal (about 4 times less, 2,148 x 10(3) microns 3 vs 658 x 10(3) microns 3 after 8 h of treatment); 4) a general segregation of the cells making up the structure, principally in the more active proliferating zones. The local alterations found are described.     

A comparison of CCS tandem overload controls

In this paper we analyse issues associated with overloads in tandem switching systems in Common Channel Signalling (CCS) networks. In particular, we examine the need for, and effectiveness of, Automatic Congestion Control (ACC), a CCS mechanism which allows a congested switching system to inform adjacent CCS nodes of its level of overload, and subsequently controls the rate at which traffic is sent to the congested node. We demonstrate the critical need for end-offices and tandem switching systems to implement some form of ACC if network performance is to be maintained during congestion, especially in tandem exchanges. In addition, we find that the presently defined ACC should be expanded to allow more levels of congestion to be reported to adjacent nodes, so that a more effective, finer grained control is produced.     

Mullite Formation by Endothermic Reaction of α-Alumina/Silica Microcomposite Particles

The formation of mullite was investigated using microcomposite powders which consist of α-alumina cores and amorphous silica coatings. Differential thermal analysis and X-ray diffraction showed that the mullitization reaction was endothermic. In contrast, mullite forms exothermically in samples prepared by sol-gel processing. The results are shown to be consistent with available thermodynamic data for mullite formation from different alumina and silica phases.