Damage evolution in polymer due to exposure to high-pressure hydrogen gas

The use of hydrogen as a fuel is increasing exponentially, and the most economical way to store and transport hydrogen for fuel use is as a high-pressure gas. Polymers are widely used for hydrogen distribution and storage systems because they are chemically inert towards hydrogen. However, when exposed to high-pressure hydrogen, some hydrogen diffuses through polymers and occupies the preexisting cavities inside the material. Upon depressurization, the hydrogen trapped inside polymer cavities can cause blistering or cracking by expanding these cavities. A continuum mechanics–based deformation model was deployed to predict the stress distribution and damage propagation while the polymer undergoes depressurization after high-pressure hydrogen exposure. The effects of cavity size, cavity location, and pressure inside the cavity on damage initiation and evolution inside the polymer were studied. The stress and damage evolution in the presence of multiple cavities was also studied, because interaction among cavities alters the damage and stress field. It was found that all these factors significantly change the stress state in the polymer, resulting in different paths for damage propagation. The effect of adding carbon black filler particles and plasticizer on the damage was also studied. It was found that damage tolerance of the polymer increases drastically with the addition of carbon black fillers, but decreases with the addition of the plasticizer.     

Structural Cues for Understanding eEF1A2 Moonlighting

Spontaneous mutations in the EEF1A2 gene cause epilepsy and severe neurological disabilities in children. The crystal structure of eEF1A2 protein purified from rabbit skeletal muscle reveals a post-translationally modified dimer that provides information about the sites of interaction with numerous binding partners, including itself, and maps these mutations onto the dimer and tetramer interfaces. The spatial locations of the side chain carboxylates of Glu301 and Glu374, to which phosphatidylethanolamine is uniquely attached via an amide bond, define the anchoring points of eEF1A2 to cellular membranes and interorganellar membrane contact sites. Additional bioinformatic and molecular modeling results provide novel structural insight into the demonstrated binding of eEF1A2 to SH3 domains, the common MAPK docking groove, filamentous actin, and phosphatidylinositol-4 kinase IIIβ. In this new light, the role of eEF1A2 as an ancient, multifaceted, and articulated G protein at the crossroads of autophagy, oncogenesis and viral replication appears very distant from the “canonical” one of delivering aminoacyl-tRNAs to the ribosome that has dominated the scene and much of the thinking for many decades.     

Crystallography of fracture facets in a near-alpha titanium alloy

A faceted initiation site is observed in Ti-6242 alloy for both the cyclic and static-loading test conditions. In this experimental study, the crystallographic orientation of the facets has been determined using the electron backscattered diffraction (EBSD) technique in conjunction with the quantitative tilt fractography in a scanning electron microscope (SEM). Quantitative tilt fractography analysis has been used to determine the spatial orientation of fracture facets. The results indicate that the normal-fatigue (no-dwell) fracture facets are oriented at ∼5 deg with respect to the basal plane; the dwell-fatigue fracture facets are oriented at ∼10 to 15 deg with respect to the basal plane and the static-loading fracture facets are oriented at ∼20 deg with respect to the basal plane. These crystallographic orientation determinations of the fracture facets at the crack-initiation site can be used to obtain an idea about the type of loading that produced them.     

点阴极电场辅助阳极连接中的紧密接触面积和电流

用等效电路的方法研究了点阴极情况下的电场辅助阳极连接效应，计算了连接电流，连接孕育期和紧密接触面积，本文结果表明，连接初期电流迅速衰减，随后缓慢变小，直至某一稳定值，孕育期随温度上升指数下降，连接温度高时，孕育期将难以观察到；待连接表面之间紧密接触面积随时间延长而非线性扩展，紧密接触区域增大时，其边界向外推进速度渐小，而接触面积增加渐快。     

Microscale wear of vitrified abrasive materials

The study of bonding hard materials such as aluminium oxide and cubic boron nitride (cBN) and the nature of interfacial cohesion between these materials and glass is very important from the perspective of high precision grinding. Vitrified grinding wheels are typically used to remove large volumes of metal and to produce components with very high tolerances. It is expected that the same grinding wheel be used for both rough and finish machining operations. Therefore, the grinding wheel, and in particular its bonding system, is expected to react differently to a variety of machining operations. In order to maintain the integrity of the grinding wheel, the bonding system that is used to hold abrasive grains in place will react differently to forces that are placed on individual bonding bridges. This paper examines the role of vitrification heat treatment on the development of strength between abrasive grains and bonding bridges, and the nature of fracture and wear in vitrified grinding wheels that are used for precision grinding applications.     

Measurement of the density and surface tension of Ni-based superalloys in the liquid and mushy states

The densities of three Ni-based superalloys have been measured in both liquid and mushy states by both a modified sessile drop method (MSDM) and a modified pycnometric method (MPM) for alloys CMSX-4 and CM186LC, and for CMSX-10 alloy by MSDM only. The surface tensions of liquid CMSX-4, CM186LC, and CMSX-10 superalloys were measured using the sessile drop method. All measurements were carried out in a highly purified argon atmosphere with the oxygen partial pressure of less than 10⁻¹⁹ MPa in the gas outlet. The densities of all superalloys in both liquid and mushy states were found to decrease with increasing temperature. The volume thermal expansion of each superalloy in the mushy state was found to be higher than that in the liquid state. The densities determined by different methods have been critically assessed and recommended values in both liquid and mushy states are given as a linear function of temperature for the three Ni-based superalloys. The surface tension of liquid CMSX-4 superalloy was found to decrease with increasing temperature, while that of liquid CMSX-10 superalloy increases with increasing temperature. The wetting behavior of liquid CM186LC on the alumina substrate was found (1) to differ significantly from that of CMSX-4 and CMSX-10 and (2) to vary with time. A HfO₂-rich layer was found in the contact area of CM186LC with the alumina substrate, which could lead to some uncertainty in the value obtained for the surface tension determined for CM186LC.     

3D design tools speed NASA space shuttle work

There will always be a premium on innovation and original approaches to old problems. Engineers and designers are constantly urged to think outside the box. In space shuttle technician Arlene S. Reese's case, she decided to think outside the world of traditional, 2D drafting. Working under tough deadline pressures for a shuttle lighting installation project, Reese and her design team decided to blend digital photographs and 3D assemblies to show other contractors precisely where and how the job should be built. The result was a faster, more effective method for planning electrical projects that has earned awards for her team and continues to produce benefits for the National Aeronautics and Space Administration (NASA). Reese and the managers at NASA say the design method can apply to many architectural and engineering disciplines.