Periodontal considerations in an overdenture population

Three variable microsatellite loci have been isolated from the American lobster, Homarus americanus. In a population sample from the Gulf of Maine, the effective numbers of alleles (Ne) for the two most variable loci were 16.33 and 13.19, respectively. Reduced variability at all three loci was seen in the European lobster, H. gammarus, for which the maximum Ne was 4.00. The reduction in variability in H. gammarus is consistent with a bottleneck event. Inheritance analysis using H. americanus demonstrated segregation of codominant alleles and the absence of linkage. Null alleles were observed at two loci in inheritance studies. This study demonstrates that microsatellite loci should be useful in studying the population structure of clawed lobsters.     

Effects of Sr/Ti-ratio in SrTiO3-based SOFC anodes investigated by the use of cone-shaped electrodes

In this work the A-site deficiency limit for undoped SrTiO₃, calcined in air or reducing atmosphere, was investigated. XRD and SEM analyses showed that when using the solid-state synthesis route it was difficult to achieve any A-site deficiency. Even very small deviations from unity in the Sr/Ti-ratio resulted in impurity phases. The effects of Sr/Ti-ratio on the performance of SrTiO₃ anodes for solid oxide fuel cells (SOFCs) was investigated by impedance spectroscopy with cone-shaped electrodes. The electrocatalytic activity of the SrTiO₃ cone samples, with various amount of reduced titanium dioxide phases (Magnéli phases), was investigated for oxidation of H₂ at 700 °C. High temperature treatment at 1000 °C, between the measurements at 700 °C, showed that high content of Magnéli phases leads to faster degradation of the activity. The suitability for using cone-shaped electrodes as a tool for investigating electrode materials is discussed.     

Practical validation of the two-fluid model applied to dense gas-solid flows in fluidized beds

This paper discusses the simulation of bubbling gas-solid flows by using the Eulerian two-fluid approach. Predictions of particle motion, bed expansion, bubble size and bubble velocity in bubbling beds containing Geldart B particles are compared with experimental results and correlations found in the literature. In addition, gas mixing in a bed of Geldart A particles is investigated.An in-house code has been developed based on the finite-volume method and the time-splitting approach using a staggered grid arrangement. The velocities in both phases are obtained by solving the 2D Reynolds-averaged Navier/Stokes equations using a partial elimination algorithm (PEA) and a coupled solver. The k-ε turbulence model is used to describe the turbulent quantities in the continuous phase.In general, the model predictions are in good agreement with experimental data found in the literature. Most important observations are: the level of the restitution coefficient was found to be crucial in order to obtain successful results from 2D axisymmetric simulations of a system containing Geldart B particles. Bubble size and bubble rise velocities are not as sensitive to the restitution coefficient. The turbulence model is of outmost importance concerning gas mixing in a fluidized bed of Geldart A particles.From these numerical analyzes an optimized granular flow two-fluid model can be designed for the purpose of simulating reactive systems in fluidized bed reactors.     

Cellulose as a binding material in graphitic anodes for Li ion batteries: a performance and degradation study

Four types of cellulose, in particular carboxy methyl cellulose (CMC), are tested as potential binding materials in graphitic anodes for lithium ion batteries. It is shown that a minimum content of a cellulose which gives acceptable anode properties (reversible capacity>300 mA h g⁻¹ during the first 10 cycles, irreversible loss<20%) is about 2 wt.%, which is less than in the case of conventional polymeric binders (5-10 wt.%). Kinetics of insertion-deinsertion and passivation processes seem not to be affected by the presence of cellulose. Explanation for the electrode failure at cellulose contents lower than 1 wt.% is given based on X-ray diffraction and microscopy investigations. Finally, the structure (distribution) of cellulose in the composite anode material is discussed and (indirectly) checked with a series of experiments. Most results are compared with the corresponding results obtained either with gelatin or conventional polymeric binders or both.     

Integratable non-clogging microconcentrator based on counter-flow principle for continuous enrichment of CaSki cells sample

This study addresses the need to reduce the risk of clogging when preparing samples for cell concentration, i.e., the CaSki Cell-lines (epidermoid cervical carcinoma cells). Aiming to develop a non-clogging microconcentrator, we proposed a new counter-flow concentration unit characterized by the directions of penetrating flows being at an obtuse angle to the main flow, due to employment of streamlined turbine blade-like micropillars. Based on the optimization results of the counter-flow unit profile, a fractal arrangement for the counter-flow concentration unit was developed. A counter-flow microconcentrator chip was then designed and fabricated, with both the processing layer and collecting layer arranged in terms of the honeycomb structure. Visualized experiments using CaSki cell samples on the microconcentrator chip demonstrated that no cell-clogging phenomena occurred during the test and that no cells were found in the final filtrate. The test results show an excellent concentration performance for the microconcentrator chip, while a concentrating ratio of >4 with the flow rate being below 1.0 ml/min. As only geometrical structure is employed in the passive device, the counter-flow microconcentrator can be easily integrated into advanced microfluidic systems. Owing to the merit of non-clogging and continuous processing ability, the counter-flow microconcentrator is not only suitable for the sample preparation within biomedical field, but also applicable in water-particle separation.     

Integrated micro Pirani gauge based hermetical package monitoring for uncooled VO x bolometer FPAs

This paper presents the design and fabrication of a micro Pirani gauge using VO _x as the sensitive material for monitoring the pressure inside a hermetical package for micro bolometer focal plane arrays (FPAs). The designed Pirani gauge working in heat dissipating mode was intentionally fabricated using standard MEMS processing which is highly compatible with the FPAs fabrication. The functional layer of the micro Pirani gauge is a VO _x thin film designed as a 100 × 200 μm pixel, suspended 2 μm above the substrate. By modeling of rarefied gas heat conduction using the Extended Fourier’s law, finite element analysis is used to investigate the sensitivity of the pressure gauge. Also the thermal interactions between the micro Pirani gauge and bolometer FPAs are verified. From the fabricated prototype, the measured device TCR is about −0.8% K⁻¹ and the sensitivity about 1.84 × 10⁻³ W K⁻¹ mbar⁻¹.     

Formation of oxidising species and their role in the viscosity loss of cereal beta-glucan extracts

The aim of this study was to determine the role of the formation of radicals and hydrogen peroxide in the viscosity loss of beta-glucan extracts from oat and barley. Radicals derived from endogenous H₂O₂ were formed spontaneously in all extracts. The decomposition of H₂O₂ by catalase had little or no effect on the viscosity, and the radical formation detected and measured by electron spin resonance (ESR) spectroscopy did not predict the shelf life of crude beta-glucan extracts. The addition of FeSO₄ accelerated the radical formation and viscosity loss, revealing the sensitivity of the extract viscosity towards catalysts for oxidation. Using 50% cadoxen in the extracts slowed down the viscosity loss in all extracts but still led to a 10–70% decrease of the initial viscosities during 4 weeks of storage. The results suggest that the viscosity loss may be a result from multiple mechanisms including chemical reactions during storage as well as aggregation and conformational changes.     

Minimum required angular resolution of smartphone displays for the human visual system

There has been a rapid increase in the resolution of small‐sized and medium‐sized displays. This study determines an upper discernible limit for display resolution. A range of resolutions varying from 254–1016 PPI were evaluated using simulated display by 49 subjects at 300 mm viewing distance. The results of the study conclusively show that users can discriminate between 339 and 508 PPI and in many cases between 508 and 1016 PPI.     

Ship roll damping control

The technical feasibility of roll motion control devices has been amply demonstrated for over 100 years. Performance, however, can still fall short of expectations because of difficulties associated with control system designs, which have proven to be far from trivial due to fundamental performance limitations and large variations of the spectral characteristics of wave-induced roll motion. This tutorial paper presents an account of the development of various ship roll motion control systems together with the challenges associated with their design. It discusses the assessment of performance and the applicability of different mathematical models, and it surveys the control methods that have been implemented and validated with full scale experiments. The paper also presents an outlook on what are believed to be potential areas of research within this topic.     

Molecular Heterojunctions of Oligo(phenylene ethynylene)s with Linear to Cruciform Framework

Electrical transport properties of molecular junctions are fundamentally affected by the energy alignment between molecular frontier orbitals (highest occupied molecular orbital (HOMO) or lowest unoccupied molecular orbital (LUMO)) and Fermi level (or work function) of electrode metals. Dithiafulvene (DTF) is used as substituent group to the oligo(phenylene ethynylene) (OPE) molecular wires and different molecular structures based on OPE3 backbone (with linear to cruciform framework) are achieved, with viable molecular orbitals and HOMO–LUMO energy gaps. OPE3, OPE3–DTF, and OPE3–tetrathiafulvalene (TTF) can form good self‐assembled monolayers (SAMs) on Au substrates. Molecular heterojunctions based on these SAMs are investigated using conducting probe–atomic force microscopy with different tips (Ag, Au, and Pt) and Fermi levels. The calibrated conductance values follow the sequence OPE3–TTF > OPE3–DTF > OPE3 irrespective of the tip metal. Rectification properties (or diode behavior) are observed in case of the Ag tip for which the work function is furthest from the HOMO levels of the OPE3s. Quantum chemical calculations of the transmission qualitatively agree with the experimental data and reproduce the substituent effect of DTF. Zero‐bias conductance, and symmetric or asymmetric couplings to the electrodes are investigated. The results indicate that improved fidelity of molecular transport measurements may be achieved by systematic studies of homologues series of molecular wires applying several different metal electrodes.