Improvement of porous polyvinylidene fluoride-co-hexafluropropylene hollow fiber membranes for sweeping gas membrane distillation of ethylene glycol solution

Porous polyvinylidene fluoride-co-hexafluropropylene (PVDF-HFP) hollow fiber membranes were fabricated through a wet spinning process. In order to improve the membrane structure, composition of the polymer solution was adjusted by studying ternary phase diagrams of polymer/solvent/non-solvent. The prepared membranes were used for sweeping gas membrane distillation (SGMD) of 20 wt% ethylene glycol (EG) aqueous solution. The membranes were characterized by different tests such as N₂ permeation, overall porosity, critical water entry pressure (CEP_w), water contact angle and collapsing pressure. From FESEM examination, addition of 3 wt% glycerol in the PVDF-HFP solution, produced membranes with smaller finger-likes cavities, higher surface porosity and smaller pore sizes. Increasing the polymer concentration up to 21 wt% resulted in a dense spongy structure which could significantly reduce the N₂ permeance. The membrane prepared by 3 wt% glycerol and 17 wt% polymer demonstrated an improved structure with mean pore size of 18 nm and a high surface porosity of 872 m^-1. CEP_w of 350 kPa and overall porosity of 84% were also obtained for the improved membrane. Collapsing pressure of the membranes relatively improved by increasing the polymer concentration. From the SGMD test, the developed membrane represented a maximum permeate flux of 28 kg·m^-2·h^-1 which is almost 19% higher than the flux of plain membrane. During 120 h of a long-term SGMD operation, a gradual flux reduction of 30% was noticed. In addition, EG rejection reduced from 100% to around 99.5% during 120 h of the operation.     

Hydrogen production by silica membrane reactor during dehydrogenation of methylcyclohexane: CFD analysis

A comprehensive computational fluid dynamic model has been developed using COMSOL Multiphysics 5.4 software to predict the behavior of a membrane reactor in dehydrogenation of methylcyclohexane for hydrogen production. A reliable reaction kinetic of dehydrogenation reaction and a permeation mechanism of hydrogen through silica membrane have been used in computational fluid dynamic modeling. For performance comparison, an equivalent traditional fixed bed reactor without hydrogen removal has been also modeled. After model validation, it has been used to evaluate the operating parameters effect on the performance of both the silica membrane reactor and the equivalent traditional reactor as well. The operating temperature ranged between 473 and 553 K, pressure between 1 and 2.5 bar, sweep factor from ?6.22 to 25 and feed flow rate from 1 to 5 × 10^?6 mol/s. The membrane reactor performed better than the equivalent traditional reactor, achieving as best result complete methylcyclohexane conversion and 96% hydrogen recovery.     

The effect of nanoclay and MWNT on fire‐retardency and mechanical properties of unsaturated polyester resins

The influence of nanomaterials such as Multi‐Walled Carbon NanoTubes (MWNT) and organoclay (Cloisite 30B) on the physical and mechanical properties of thermoset matrix such as Unsaturated Polyester (UP) resins is investigated. Although styrene containing UP resins have a wide spread application in industry, lack of information exists regarding the behavior of MWNT/organoclay/polyester ternary nanocomposite systems. The main aim of this research was first to evaluate the effect of nanofiller on the flammability of UP resins and, second, to characterize their mechanical properties such as toughness and their tensile strength. The rheological studies showed shear thinning for samples of UP resins containing MWNT and Cloisite 30B. The cone calorimetry measurement was used to evaluate the flame‐retardency, the gas emission of the nanocomposite and whether or not this system can be designated as a nanocomposite. This was understood in the test by the peak heat release rate being lowered and shifted to shorter times. Furthermore, the tensile and impact properties of samples were evaluated. The obtained results indicated that nanofiller particles caused both increase and decrease in the impact and tensile strength. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Study of Unrecovered Strain and Critical Stresses in One-Way Shape Memory Nitinol

Unique thermomechanical properties of Nitinol known as shape memory and superelasticity make it applicable for different fields such as biomedical, structural, and aerospace engineering. These unique properties are due to the comparatively large recoverable strain, which is being produced in a martensitic phase transformation. However, under certain ranges of stresses and temperatures, Nitinol wires exhibit unrecovered strain. For cyclic applications, it is important to understand the strain behavior of Nitinol wires. In this study, the unrecovered strain of different Nitinol wire diameters was investigated using constant stress experiment. Uniaxial tensile test has been also performed to find the range of critical stresses. It was observed that the unrecovered strain produced in the first loading-unloading cycle affects the total strain in the subsequent cycles. Moreover, a critical range of stress was found beyond which the unrecovered strain was negligible while the wires heated up to the range of 70-80°C, depending on the wire diameters. The unrecovered strain of wire diameters of 0.19 mm and less was found to be sensitive to the critical stress. On the other hand, for wire diameters bigger than 0.19 mm this connection between the unrecovered strain and the critical stress was not observed for the same range of heating temperature.     

Tracheobronchiomegaly (Mounier-Kuhn syndrome)

Tracheobronchiomegaly is a rare congenital disorder due to defective development of elastic and muscle tissues in the upper airways. The characteristic radiologic features shown by bronchography include marked dilatation of the tracheobronchial system and diffuse saccular bronchiectasis. These findings and recurrent episodes of pneumonia lead to a progressive loss of pulmonary function. Even with vigorous medical therapy the prognosis is poor and severe respiratory failure eventually develops.     

Three Dimensional Characterization of Defects by Ultrasonic Time-of-Flight Diffraction (ToFD) Technique

Ultrasonic time-of-flight diffraction (ToFD) technique has high accuracy in locating and sizing discontinuities. The primary reason for this accuracy is the use of time instead of amplitude for measurement of the depth and size of discontinuities. Despite the many advantages of ToFD, it suffers from a number of shortcomings, the most notable one being its two-dimensional character. The goal of this paper is to develop an algorithm, as a prerequisite, to extend ToFD measurements to a three-dimensional space. For this purpose, a combination of multiple transmitting and receiving probes is proposed instead of just one pair commonly used in ToFD measurements. The approach for locating and sizing defects in a 3D space follows the methods used in radar and acoustic positioning systems. Non-iterative techniques are used for positioning a single source (defect) based on signals collected by several transducers. The estimation formula, in the form of a closed-form solution, is derived by linear least-squares minimization. In addition to existing conventional passive algorithms, a new active algorithm is also proposed for the general arrangement of transducers. This algorithm is tested on a steel specimen having an artificially implanted discontinuity and the three-dimensional location of the defect is estimated.     

Experimental investigation of the effect of using the cylindrical parabolic collector,different solar panels and their cooling on seawater desalination in double-slope solar still

ABSTRACT

The present study was aimed at examining the effect of using solar panels and cylindrical parabolic collectors, or CPCs, on solar still unit. Cooling of the solar panels up to 25°C has been also conducted in order to rise the amount of produced freshwater. In the first setup, the solar still unit has been made up of 300 W and 600 W solar panels along with the CPC devices of lengths 1 m and 2 m outside for water heating. The second setup was designed in a way that water is heated by the solar panels as well as the CPC device with the copper pipe circulation inside the solar still unit, so the hot water within the pipe has raised the temperature of the water as a heat exchanger inside the solar still. Based on the results, the second setup had a higher efficiency than the first setup. Moreover, the highest amount of fresh water was 4.215 kg and 5.091 kg during one day in the first setup and the second setup, respectively. Cases 1 to 6 are related to the first setup and cases 7 to 12 are related to the second setup. The lowest fresh water production in case 1 was 2.852 kg. the highest water temperature in experimental setup 1 was 71.9 °C and in experimental setup 2 was 84.8°C.     

Increasing Angiogenesis Factors in Hypoxic Diabetic Wound Conditions by siRNA Delivery: Additive Effect of LbL-Gold Nanocarriers and Desloratadine-Induced Lysosomal Escape

Impaired wound healing in people with diabetes has multifactorial causes, with insufficient neovascularization being one of the most important. Hypoxia-inducible factor-1 (HIF-1) plays a central role in the hypoxia-induced response by activating angiogenesis factors. As its activity is under precise regulatory control of prolyl-hydroxylase domain 2 (PHD-2), downregulation of PHD-2 by small interfering RNA (siRNA) could stabilize HIF-1α and, therefore, upregulate the expression of pro-angiogenic factors as well. Intracellular delivery of siRNA can be achieved with nanocarriers that must fulfill several requirements, including high stability, low toxicity, and high transfection efficiency. Here, we designed and compared the performance of layer-by-layer self-assembled siRNA-loaded gold nanoparticles with two different outer layers—Chitosan (AuNP@CS) and Poly L-arginine (AuNP@PLA). Although both formulations have exactly the same core, we find that a PLA outer layer improves the endosomal escape of siRNA, and therefore, transfection efficiency, after endocytic uptake in NIH-3T3 cells. Furthermore, we found that endosomal escape of AuNP@PLA could be improved further when cells were additionally treated with desloratadine, thus outperforming commercial reagents such as Lipofectamine^® and jetPRIME^®. AuNP@PLA in combination with desloratadine was proven to induce PHD-2 silencing in fibroblasts, allowing upregulation of pro-angiogenic pathways. This finding in an in vitro context constitutes a first step towards improving diabetic wound healing with siRNA therapy.     

Extraction of ferulic acid from sugar beet pulp by alkaline hydrolysis and organic solvent methods

Extraction of ferulic acid from sugar beet pulp was carried out using three extraction solvents, sodium hydroxide (0.5, 1, 2 M), methanol and their mixture (alkaline methanolic solvent). The Ferulic acid extracted by each solvent was identified and quantified by HPLC method and the effects of solvent type, concentration and reaction time on ferulic acid solubilisation were assessed. There were differences in the contents of products extracted in the experiment conditions. The minimum amount of ferulic acid was obtained from methanolic extract while the highest concentrations (957.4 mg/L ferulic acid) were obtained employing the highest NaOH concentration (2 M), and reaction time (12 h), so phenolic compounds are better released with alkaline hydrolysis than in methanol conditions. Finally a simple procedure for the purification of ferulic acid from the alkaline extracts is presented and evaluated by FT-IR spectrum.