Serotype-specific amplification of Rickettsia tsutsugamushi DNA by nested polymerase chain reaction

Polymerase chain reaction (PCR) with nested primer pairs was used to diagnose scrub typhus and identify the Rickettsia tsutsugamushi serotype. The primer pairs used for PCR were designed on the basis of the nucleotide sequence of the gene that encodes the 56-kDa antigen. Serotype-specific primers were used in the second PCR amplification. Five serovariants, the Gilliam, Karp, Kato, Kawasaki, and Kuroki strains of R. tsutsugamushi, were identified by nested PCR. In addition, the serotype identified by PCR with DNA from blood clots was the same as that of the strain isolated from five patients with scrub typhus. These findings indicate that this method is useful for diagnosis and identification of the rickettsial serotype in infected patients.     

Radiation detector made of a high-quality polycrystalline diamond

Radiation detector was made of a high-quality CVD polycrystalline diamond composed of frost column like structure diamond grains, and induced charge distribution spectra and drift velocities were measured by using alpha particles. As a result, the CVD polycrystalline achieved maximum induced charge of 83% of HP/HT type IIa diamond. Moreover, the CVD crystal had lower charge loss on electrons compared with the HP/HT type IIa diamond. Drift velocities of electrons and holes were v_e = 7.7 × 10⁴ and v_h = 7.3 × 10⁴cm/s at an electric field of 20 kV/cm, respectively. In addition, response function measurement for 14 MeV neutrons was carried out.     

A wide-bandwidth low-noise InGaAsP-InAlAs superlattice avalanchephotodiode with a flip-chip structure for wavelengths of 1.3 and 1.55μm

The authors reports the fabrication of a flip-chip InGaAsP-InAlAs superlattice avalanche photodiode using gas source molecular beam epitaxy. The incident light reaches the InGaAs photoabsorption layer through the InP substrate and an InGaAsP-InAlAs superlattice multiplication region which are transparent for wavelengths of 1.55 and 1.3 μm. The light reflection by the electrode enables the absorption layer to be as thin as 0.8 μm without significantly reducing the quantum efficiency. A maximum bandwidth of 17 GHz was obtained at a low multiplication factor because the transit time through the absorption layer is reduced     

Relationship between Transformation Temperature and Time-Temperature-Transformation Curves of Tetragonal-to-Monoclinic Martensitic Transformation in Zirconia-Yttria System

The tetragonal → monoclinic ( t → m ) martensitic phase transformation in ZrO₂–0.5–4 mol% Y₂O₃ proceeds during isothermal aging at various temperatures from 350 to 800 K; i.e., the transformation increases sigmoidally with aging time. The time-temperature-transformation ( T - T - T ) curves show a typical C shape, with very high rate for lower Y₂O₃-content specimens, and the rate decreases with higher Y₂O₃ content. The transformation temperature ( M _s) of the t → m transformation obtained from dilatation curves during the cooling stage coincides well with C curves above the nose temperature. The t → m transformation should occur isothermally, as suggested by a nucleation and growth mode.     

《时尚学:时尚研究概述》前言

本文是<时尚学:时尚研究概述>(Fashion-ology:An Introduction to Fashion Studies)一书的前言部分,概括了书中的一些主要观点.作者认为应该将对时尚的研究与对衣着的研究区分开来.时尚无关服饰,它只是一种信仰.她主张应该把时尚研究列入社会科学、人文科学的研究范围内,并介绍了人们在心理学、社会心理学、历史学、艺术史、文化人类学和经济学等领域对时尚的研究.她所提倡的时尚理论认为,对时尚的研究应该从时尚系统入手,研究它整个运作过程中的社会属性.     

Short- and long-term strength characteristics of particulate-filled cast epoxy resin

Particulate-filled thermosetting composites are widely used, yet little systematic work has been done on their long-term strength characteristics. In this study short-term tensile, flexural, and impact tests as well as tensile creep-rupture tests were made for unfilled and filled epoxy to clarify the effects of filler size, filler content, and temperature. Fillers used were silica, alumina particles, and glass beads. Test temperatures were varied from 25 to 110°C. As a result of short-term testing, it was found that the Petch relation held between strength and filler size if brittle fracture occurred, while a strength and filler size if brittle fracture occurred, while a strengthening effect existed when ductile fracture occurred. On creeprupture testing, a strengthening is observed with filler size and content for silica and glass beads. The Arrhenius plot of rupture time for various filler sizes and contents converges to a characteristic point corresponding to the glass transition temperature of the material. Using this relation, a modified Larson-Miller master rupture curve is proposed which can predict the long-term strength of particulate-filled thermosetting composites as functions of rupture time, temperature, filler size, and content.     

Optimal assignment method for mobile assistive robots using matching theory

Artificial Life and Robotics - The aging population and expectations for nursing care robots increased significantly recently. We focused on mobile assistive robots. When various types of robots...