Study of the morphology and mechanical properties of polypropylene composites with silica or rice‐husk

The mechanical, morphological behavior and water absorption characteristics of polypropylene (PP) and silica, or PP and rice‐husk, composites have been studied. The silica used in this study as filler was a commercial type produced from soluble glass or rice husks. The compatibilizing effect of PP grafted with monomethyl itaconate (PP‐g‐MMI) and/or with vinyltriethoxysilane (PP‐g‐VTES) as polar monomers on the mechanical properties and water absorption was also investigated. In general, a high loading of the studied fillers in the polymer matrix increases the stiffness and the water absorption capacity. This effect is more noticeable in the tensile modulus of the PP/silica composite with PP‐g‐VTES as compatibilizer. However, the increase of the rice‐husk charge as a natural filler in the PP matrix decreases the stiffness, and in the presence of PP‐g‐MMI as compatibilizer in PP/rice‐husk, the tensile modulus and water absorption of the composite were improved. The better adhesion and phase continuity in the PP/silica and PP/rice‐husk composites with different compatibilizers was confirmed by the morphological study. Copyright © 2004 Society of Chemical Industry     

Evaluating the influence of multiplexing schemes and buffer implementation on perceived VoIP conversation quality

This work presents a study of RTP multiplexing schemes, which are compared with the normal use of RTP, in terms of experienced quality. Bandwidth saving, latency and packet loss for different options are studied, and some tests of Voice over IP (VoIP) traffic are carried out in order to compare the quality obtained using different implementations of the router buffer. Voice quality is calculated using ITU R-factor, which is a widely accepted quality estimator. The tests show the bandwidth savings of multiplexing, and also the importance of packet size for certain buffers, as latency and packet loss may be affected. The customer’s experience improvement is measured, showing that the use of multiplexing can be interesting in some scenarios, like an enterprise with different offices connected via the Internet. The system is also tested using different numbers of samples per packet, and the distribution of the flows into different tunnels is found to be an important factor in order to achieve an optimal perceived quality for each kind of buffer. Grouping all the flows into a single tunnel will not always be the best solution, as the increase of the number of flows does not improve bandwidth efficiency indefinitely. If the buffer penalizes big packets, it will be better to group the flows into a number of tunnels. The router processing capacity has to be taken into account too, as the limit of packets per second it can manage must not be exceeded. The obtained results show that multiplexing is a good way to improve customer’s experience of VoIP in scenarios where many RTP flows share the same path.     

Determination of trace manganese and Ni in neem oil by ETA-AAS with emulsion sample introduction

An emulsion-based method was developed as an alternative for the introduction of oil-based samples into a graphite furnace to produce a more rapid, precise, and accurate method of analysis. The combination of emulsion sampling and electrothermal atomization for atomic absorption spectroscopy was developed and then applied to the determination of Ni and manganese in neem oil from Venezuela. The optimal concentration of neem oil in the emulsion was 30 and 4% for Ni and Mn, respectively, based on the metal concentration of the neem oil. The stability of the emulsion as a function of time was evaluated. The use of aqueous calibration solutions and the accuracy attained using this method make it attractive for the analysis of oil samples. The metal recovery was between 97 and 101%. Based on the emulsion method, the neem oil samples had 1.39 and 0.21 mg of Mn and Ni per kg of oil, respectively. The wet digestion method indicated a Mn and Ni concentration in the neem oil sample of 1.42 and 0.24 mg/kg, respectively.     

FAIRNESS IN RECURRENT AUCTIONS WITH COMPETING MARKETS AND SUPPLY FLUCTUATIONS

Auctions have been used to deal with resource allocation in multiagent environments, especially in service‐oriented electronic markets. In this type of market, resources are perishable and auctions are repeated over time with the same or a very similar set of agents. In this scenario it is advisable to use recurrent auctions: a sequence of auctions of any kind where the result of one auction may influence the following one. Some problems do appear in these situations, as for instance, the bidder drop problem, the asymmetric balance of negotiation power or resource waste, which could cause the market to collapse. Fair mechanisms can be useful to minimize the effects of these problems. With this aim, we have analyzed four previous fair mechanisms under dynamic scenarios and we have proposed a new one that takes into account changes in the supply as well as the presence of alternative marketplaces. We experimentally show how the new mechanism presents a higher average performance under all simulated conditions, resulting in a higher profit for the auctioneer than with the previous ones, and in most cases avoiding the waste of resources.     

Thermal,hydrolytic, anticorrosive,and tribological properties of alkyd‐silicone hyperbranched resins with high solid content

Novel alkyd hyperbranched resins (AHBRs) modified with a Z‐6018 silicone (a polysiloxane intermediate) and with high solid content were synthesized by etherification reaction using an acid catalyst. Different molar ratios of AHBR to silicone were used. Structural, thermal, hydrolytic, anticorrosive, and tribological properties were studied using infrared (IR) analysis, nuclear magnetic resonance (NMR), vapor pressure osmometry (VPO), thermogravimetric analysis (TGA), acid value, electrochemical impedance spectroscopy (EIS), and pin‐on‐disk friction. IR and NMR provide evidence of grafting of the silicone on AHBR; the efficiency of grafting was quantified by TGA. Thermal stability was studied also by acid value analysis. Grafting increases the number average molecular mass, enhances thermal stability, and improves significantly hydrolytic stability. Corrosion resistance on steel is improved by two orders of magnitude, hence our modified materials can be used as highly effective anticorrosion coatings. Grafting lowers dynamic friction dramatically, more so at higher concentrations of silicone. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Polyfunctional macromonomers obtained from 2,2‐bis(hydroxymethyl) propanoic acid and tall oil fatty acids

Macromonomers (MMs) were obtained with different proportions of dimethylolpropionic acid (DMPA) and tall oil fatty acid (TOFA). The MMs were characterized by their acid value (AV), their hydroxyl value (OHV), IR spectroscopy, NMR, electrospray ionization–mass spectrometry, UV spectroscopy, rheological, differential scanning calorimetry, thermogravimetric analysis, gloss, flexibility, and adherence analyses. The presence of hydroxyl and ester groups and double bonds were confirmed by IR and NMR analyses. IR analysis showed that the intensity of the OH groups decreased with the addition of TOFA. In all cases, the AVs of the MMs were lower than those of DMPA and TOFA. By electrospray ionization–mass spectrometry, the formation of the DMPA homopolymers and structures with molecular weights higher than that of DMPA were observed. All of the MMs were amorphous. The viscosity of the MMs decreased with the addition of TOFA. The gloss values of the MMs at 85° were higher than 100, and the flexibility was good. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42029.     

Waterborne star-shaped styrene-alkyd resins

Waterborne star-shaped styrene-alkyd resins (SSARs) were synthesized from a branched alkyd resin (AR) and styrene (St) by miniemulsion polymerization. SSARs are an environmentally friendly material. The ratio of AR to St for obtaining SSARs was as follows: 50:50 (SSAR1), 60:40 (SSAR2), 70:30 (SSAR3), and 80:20 (SSAR4). The conversion percentage was directly proportional to St used, and was higher than 94.0 %. Infrared analysis and protonic nuclear magnetic resonance revealed the reaction between AR and St. The synthesis process also leads to the formation of polystyrene and its concentration increases with the concentration of St. The values of the reacted double-bond fractions were higher than 17.80%. The SSARs drop size was bigger than the particle size. The miniemulsion colloidal stability was good at room temperature. The SSARs zeta potential was between −55 and −90 mV. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48386.     

Flue gas cleaning in power stations by using electron beam technology. Influence on PAH emissions

The electron beam technology (EBT), proven treatment for SO₂ and NO_x removal, is applied to different power stations as hot gas cleaning system. In this paper, an assessment of this technique installed in a Bulgarian power station on organic emissions is analyzed. The Polycyclic Aromatic Hydrocarbons (PAH) content, not only emitted in the gas phase but also trapped in the solid phase, has been carried out before and after the irradiation. The main aim has been to know whether the EBT affects organic emissions, like PAH, as it happens with inorganic pollutants, like SO₂ and NO_x, studying EBT effects from an organic environmental point of view.     

Fertigation in Furrows and Level Furrow Systems. II: Field Experiments, Model Calibration, and Practical Applications

Furrow fertigation can be an interesting practice when compared to traditional overland fertilizer application. In the first paper of this series, a model for furrow fertigation was presented. The simulation model combined overland water flow (Saint-Venant equations), solute transport (advection-dispersion), and infiltration. Particular attention was paid to the treatment of junctions present in level furrow systems. In this paper, the proposed model is validated using five furrow fertigation evaluations differing in irrigation discharge, fertilizer application timing, and furrow geometry. Model parameters for infiltration and roughness were estimated using error minimization techniques. The error norm was based on observed and simulated values of advance time, flow depth, and fertilizer concentration. Model parameters could be adequately predicted from just one discharge experiment, although the use of more experiments resulted in decreased error. The validated model was applied to the simulation of a level furrow system from the literature. The model adequately reproduced irrigation advance and flow depth. Fertigation events differing in application timing were simulated to identify conditions leading to adequate fertilizer uniformity.