小型饮料瓶盖颜色识别系统设计与实现

目的：解决当前饮料瓶盖检测系统功能单一、体积偏大、颜色识别率低的问题。方法：提出一种基于ARM处理器的小型饮料瓶盖颜色识别系统设计方案，通过仿真软件HyperLynx的LineSim工具设计四层PCB板，设置传输线参数并进行阻抗匹配仿真分析；利用编译软件Jupyter Notebook实现阈值设置、目标轮廓检测、目标框出等功能。结果：在强、弱光条件下，识别系统对红、绿、蓝3种颜色瓶盖的识别率达到92.7%。结论：与傅里叶描述子相比，该识别系统识别准确率和精度更高，同时系统也具有人脸识别功能，适用于各种智能应用场景。     

Fabrication of barium titanate ceramics via digital light processing 3D printing by using high refractive index monomer

A digital light processing (DLP) technology has been developed for 3D printing lead-free barium titanate (BTO) piezoelectric ceramics. By comparing the curing and rheological properties of slurries with different photosensitive monomer, a high refractive index monomer acryloyl morpholine (ACMO) was chosen, and a design and preparation method of BTO slurry with high solid content, low viscosity and high curing ability was proposed. By further selecting the printing parameters, the single-layer exposure time was reduced and the forming efficiency has been greatly improved. Sintered specimens were obtained after a nitrogen-air double-step debinding and furnace sintering process, and the BTO ceramics fabricated with 80 wt% slurry shows the highest relative density (95.32 %) and piezoelectric constant (168.1 pC/N). Furthermore, complex-structured BTO ceramics were prepared, impregnated by epoxy resin and finally assembly made into hydrophones, which has significance for the future design and manufacture of piezoelectric ceramic-based composites that used in functional devices.     

Re-evaluation of Radiation-Energy Transfer to an Extraction Solvent in a Minor-Actinide-Separation Process Based on Consideration of Radiation Permeability

ABSTRACT

Absorbed-dose estimation is essential for evaluation of the radiation tolerance of minor-actinide-separation processes. We propose a dose-evaluation method based on radiation permeability, with comparisons of heterogeneous structures seen in the solvent-extraction process, such as emulsions forming in the mixture of the organic and aqueous phases. A demonstration of radiation-energy-transfer simulation is performed with a focus on the minor-actinide-recovery process from high-level liquid waste with the aid of the Monte Carlo radiation-transport code PHITS. The simulation results indicate that the dose absorbed by the extraction solvent from alpha radiation depends upon the emulsion structure, and that from beta and gamma radiation depends upon the mixer-settler-apparatus size. Non-negligible contributions of well-permeable gamma rays were indicated in terms of the plant operation of the minor-actinide-separation process.     

Effect of MoS2/PTFE coatings on performance of Si3N4/TiC ceramics in dry sliding against WC/Co

To enhance the tribological performance of Si₃N₄/TiC ceramics, MoS₂/PTFE composite coatings were deposited on the ceramic substrate through spraying method. The micrographs and basic properties of the MoS₂/PTFE coated samples were investigated. Dry sliding friction experiments against WC/Co ball were performed with the coated ceramics and traditional ones. These results showed that the composite coatings could significantly reduce the friction coefficient of ceramics, and protect the substrate from adhesion wear. The primary tribological mechanisms of the coated ceramics were abrasive wear, coating spalling and delamination, and the tribological property was transited from slight wear to serious wear with the increase of load because of the lower surface hardness and shear strength. The possible mechanisms for the effects of MoS₂/PTFE composite coatings on the friction performance of ceramics were discussed.     

基于电机效率的纯电动汽车传动系统参数匹配研究

为降低能耗、提高续航里程,本文提出了以提高电机效率为目标的纯电动汽车三档变速传动方案.首先,在分析电机工作特性的基础上提出了三档传动系统参数匹配方法;然后以某纯电动汽车为研究对象,对其驱动系统进行了改动:方案一在不改变原车型动力系统参数的情况下将传动系统由一档改为三档,并运用所提出的方法确定各档位的传动比;方案二在满足整车动力性指标要求下对电机重新选型并匹配三档传动系统;最后利用ADVISOR软件进行NEDC工况仿真分析.结果表明:在不改变原车型动力系统参数的情况下,采用三档传动可使整车的动力性和经济性都有一定的提升,续航里程提高了 9.2％,百公里电耗降低了 1.28 kW·h;重新选型电机后,采用三档传动续航里程提高了 14.1％,百公里电耗降低了 1.87kW·h.     

Preparation and flocculation properties of biodegradable konjac glucomannan-grafted poly(trimethyl allyl ammonium chloride)

Polymer Bulletin - Preparation of konjac glucomannan-grafted poly(trimethyl allyl ammonium chloride) (KGM-g-PTMAAC) was carried out using KGM as polysaccharide matrix and TMAAC as cationic...     

职业能力导向下的高职实用性体育课程改革探析——以常州信息职业技术学院为例

现行的高职体育教学多是沿用普通高等学校的课程体系,课程内容并未反映高职教育应有的教育特点,没有很好地发挥体育教学与职业教育相衔接的教学效果.通过职业能力导向下高职实用性体育课程的实施,可以很好地培养学生未来工作岗位所需要的职业体能,提高职业身体素质,从而更好地服务高职教育的发展.     

碳脱氧在钢包顶渣改质中的应用

 为了进一步降低夹杂物缺陷并提高产品质量,基于碳脱氧进行了钢包顶渣改质的研究。冷轧产品的生产工艺为铁水预处理→转炉→RH精炼→连铸,为减少钢中夹杂物质量分数,需要进行钢包顶渣改质,同时降低钢包顶渣TFe质量分数。采用粒碳部分替代铝渣球的方法进行基于碳脱氧工艺的钢包顶渣改质,试验结果表明,顶渣改质效果良好,在顶渣TFe质量分数、中间包钢水游离氧明显降低的同时铸坯中Al₂O₃夹杂物得到优化;“30 kg粒渣+铝渣球”工艺降低生产成本5.16元/t(钢)。