Effects of post annealing on removal of defect states in silicon oxynitride films grown by oxidation of silicon substrates nitrided in inductively coupled nitrogen plasma

Ultra thin (5 nm) silicon oxynitride (SiON) films were fabricated at a low temperature using nitrogen plasma generated by an inductively coupled plasma system. Effects of post-metalization annealing (PMA) of Al/SiON/Si MOS structure on the electrical properties of the SiON films were studied and correlations between the charge trapping states and the leakage current were established. Positive charge trapping by interface states generated by plasma damage was characterized by the hysteresis in high-frequency capacitance-voltage (C-V) characteristics. Hysteresis was observed to be completely removed by PMA while interface state density at the Si mid band gap reduced from 2.2×10¹³ to 3.7×10¹¹/eV/cm² and the oxide fixed charge density changed from 3.3×10¹² to −4×10¹¹/cm². The leakage current also decreased significantly, by more than two orders of magnitude, with PMA. The analysis of the leakage current using trap assisted tunneling (TAT) mechanism indicated that with PMA, the trap energy level in the SiON film becomes shallower from 1.3 to 0.7 eV. The positive trapped charges were observed to be annihilated by PMA and the trapping sites became neutral trap centers in the SiON film. This could lead to the reduction in the leakage current component given rise to by TAT.     

Differentiation of smooth muscle cells from undifferentiated cells of chicken gizzard occurs on the layer of fibroblast-like cells

Conflicting results have been reported in literature about the influence of beta-adrenergic stimulation on the fast cardiac sodium current (INa+). To elucidate these mechanisms in multicellular preparations we used the loose-patch-clamp technique to evaluate the effect of the beta-adrenergic agonist isoproterenol 1-1000 nmol/l. Isoproterenol enhanced INa+ at all membrane potentials by elevation of the maximal available INa+ . Only at the high concentration of 1 micromol/l was INa+ slightly depressed after depolarizing conditioning clamps. The most marked increase of the maximal available INa+ was 30+/-9% after application of 100 nmol/l isoproterenol. To learn about the mechanisms in view of sodium channel modulation we combined isoproterenol with the sodium channel blocker lidocaine (47 micromol/l). Under these circumstances the effects of both drugs were completely independent. This investigation shows clearly that low concentrations of isoproterenol increase INa+ in multicellular preparations by a gating-independent mechanism.     

Direct evidence of high DNA binding activity of transcription factor AP-1 in rheumatoid arthritis synovium

Green fluorescent protein (GFP) is increasingly being used in plant biology from the cellular level to whole plant level. At the cellular level, GFP is being used as an in vivo reporter to assess frequency of transient and stable transformation. GFP has also proven to be an invaluable tool in monitoring trafficking and subcellular localization of protein. At the organ level and up, many exciting applications are rapidly emerging. The development of brighter GFP mutants with more robust folding properties has enabled better macroscopic visualization of GFP in whole leaves and plants. One interesting example has been the use of GFP to monitor virus movement in and among whole plants. GFP is also emerging as a powerful tool to monitor transgene movement and transgenic plants in the field. In a proof-of-concept study, tobacco was transformed with a modified version of the GFP gene controlled by a constitutive (35S) promoter. GFP expression in progeny plants ranged from 0% to 0.5%, and approximately 0.1% GFP was the minimal amount needed for unambiguous macroscopic detection. GFP is the first truly in vivo reporter system useful in whole plants, and we project its usefulness will increase even further as better forms of GFP genes become available.     

Digitally tunable optical filters using arrayed-waveguide grating(AWG) multiplexers and optical switches

Two novel configurations for digitally tunable optical filters based on arrayed-waveguide grating (AWG) multiplexers are described in detail with emphasis on the connection of the AWG multiplexer and optical switches. Performance comparisons show that conventional configurations are disadvantaged by the switch size required and loss imbalance among the optical frequency-division-multiplexed (FDM) channels; the proposed configurations require only O(√(N)) switch elements to select one of N FDM channels, and the loss imbalance is lower by up to 75% in decibel     

Highly reliable 200 mW AlGaAs laser diode with fundamental transverse mode

A highly reliable 200 mW AlGaAs laser diode with a fundamental transverse mode has been developed, by optimising its structure with a 0.8 mu m thick p-cladding layer, a 1200 mu m long cavity length, and a front facet coating with a low reflectivity of 2%. The maximum output power was 500 mW, and stable fundamental transverse mode operation was obtained up to 350 mW. Stable operation under 200 mW and 50 degrees C was confirmed for more than 1200 h. Optical feedback noise was below 3*10/sup -14/ Hz/sup -1/.<>     

The TINA initiative [intelligent networks]

The telecommunications information networking architecture (TINA), which builds on the current advances in broadband communication and distributed computing technologies, specifying a software-based architecture for future information networks that are required to transport multimedia information and manage multimedia communication, is described. An important aspect of the architecture is that service segment functions are separated from delivery segment functions. Another key aspect is the elimination of the rigid division between network applications and operations applications that exists in current-day networks. In the TINA architecture, both kinds of applications execute on a common distributed processing platform that hides from applications the effects and complexities introduced by distribution. The architecture supports application interoperability enabling flexible construction of services, composed of service components distributed across network domains, allowing network operators and service providers to cooperatively meet the needs of the user     

Ruthenium dye-sensitized SnO2/TiO2 coupled solar cells

The photoelectrochemical behaviors of RuL₂(NCS)₂ dye-sensitized SnO₂/TiO₂ coupled solar cell was studied and compared with TiO₂ single system. The coupled system shows higher incident photon-to-current conversion efficiency (IPCE) value than the single system. A maximum IPCE value in the coupled system with 3.5 μm-thick SnO₂ and 7 μm-thick TiO₂ attained 82.4% at 530 nm wavelength. The higher IPCE value in the coupled system is attributed to the charge separation by fast electron transfer process from the excited RuL₂(NCS)₂ dye to TiO₂ to SnO₂ in the system with different energy level.     

Evaluation of inelastic constitutive models under plasticity-creep interaction for steel at 600°C

Uniaxial tests to identify plasticity-creep interaction in steel at 600°C were carried out as the Benchmark Project by the Subcommittee on Inelastic Analysis and Life Prediction, JSMS. The purpose of this paper is to present recent experimental data and predictions of constitutive models obtained in the project. Ten types of constitutive models were utilized to compare analytical predictions to sixteen benchmark experiments which are grouped into four categories: (I) tensile and creep tests under monotonic loading, (II) mixed mode tests under plastic and creep loading, (III) ratcheting deformation tests under program loads, and (IV) cyclic deformation tests under the combination of different strain rates. The benchmark tests in Group IV are used to estimate the creep-fatigue life of steel; the results will be published in a separate paper.     

Low-loss athermal silica-based lattice-form interleave filter with silicone-filled grooves

We describe a low-loss athermal silica-based interleave filter with a lattice-form structure. We athermalize the filter by using a silicone-filled groove formed in each delay line and we employ a low-loss design to reduce the accumulated groove excess loss in the multiple delay lines. By using these designs, we obtained a very low groove excess loss of 0.4 dB and achieved satisfactory temperature insensitivity and optical characteristics with this filter.