Performance of the bearing reinforcement earth wall as a retaining structure in the Mae Moh mine,Thailand

In this research, a Bearing Reinforcement Earth (BRE) wall with a residual clay stone backfill was successfully implemented as an alternative truck ramp support for an on-site crusher plant in the Mae Moh mine, Thailand. The performance of the BRE wall during and after the end of construction as well as during the service state was evaluated in terms of, settlement, bearing stress, lateral movement, lateral earth pressure and tension force in the reinforcements. Bearing reinforcement is a cost-effective inextensible earth reinforcement, which is composed of a longitudinal member and transverse members. The maximum settlement at the end of construction (20 days) was about 5 mm. The installation of the truck ramp (10 days after the end of construction) resulted in an immediate settlement of about 2 mm. The final settlement due to the backfill, truck ramp and truck load after 270 days was found to be uniform due to the contribution of bearing reinforcement and was approximately 25 mm. The bearing stress which was uniformly distributed was found to increase rapidly with construction time, which was in agreement with the relatively uniform settlements. The lateral wall movement at the front and lateral sides at the end of construction was very small with the maximum movement (at the top of the wall) found to be less than 10 mm. As such, the ratio of lateral movement to height (δ/H) was found to be approximately 0.12%, which was lower than the allowable value of 0.4%. With this low δ/H and the insignificant change in the measured settlement and lateral movement during service, the BRE wall was considered to have a very high stability. The coefficients of lateral earth pressure, K and depth relationship were proposed based on the analysis of measured maximum tensile force in the reinforcements. The maximum tension plane of the BRE wall could be represented by the coherent gravity hypothesis. Using the proposed K and maximum tension plane, the internal stability of the BRE wall was furthermore examined. A proposed method of designing the BRE wall with claystone backfill was also proposed.     

Strength Development in Cement Admixed Bangkok Clay: Laboratory and Field Investigations

The in-situ deep mixing technique has been established as an effective means to effect columnar inclusions into soft Bangkok clay to enhance bearing capacity and reduce settlement. In this paper, an attempt is made to identify the critical factors governing the strength development in cement admixed Bangkok clay in both the laboratory and the field. It is found that clay-water/cement ratio, w_c/C is the prime parameter controlling the laboratory strength development when the liquidity index varies between 1 and 2. Based on this parameter and Abrams' law, the strength prediction equation for various curing times and combinations of clay water content and cement content is proposed and verified. This will help minimize the number of trials necessary to arrive at the quantity of cement to be admixed. Besides the w_c/C, the strength of deep mixing column is controlled by the execution and curing conditions. For low strength improvement (laboratory 28-day strength less than 1,500 kPa), the field strength of the deep mixing columns, q_uf, made up from both dry and wet mixing methods is higher than 0.6 times the laboratory strength, q_ul. The q_uf/q_ul ratios for the wet mixing columns are generally higher than those for the dry mixing columns. This higher strength ratio is due to the dissipation of the excess water in the column (consolidation) caused by the field stress. The water to cement ratio, W/C, of 1.0 is recommended for the wet mixing method of the soft Bangkok clay. A fast installation rate was shown to provide high quality for low strength columns. Suggestions are made for improving the deep mixing of soft Bangkok clay, which are very useful both from economic and engineering viewpoints.     

Assessment of strength development in blended cement admixed Bangkok clay

Fly ash and biomass ash have been widely accepted as waste materials substituting Portland cement. In this paper, the role of these two ashes on the strength development of cement admixed low-swelling Bangkok clay is investigated via unconfined compressive (UC) test and thermal gravity (TG) analysis. Fly ash and biomass ash are dispersing materials, increasing the reactive surface of the cement grains. The pozzolanic reaction does not play any significant role on the strength development with time since the amount of Ca(OH)₂ is insufficient to react with the ashes. The contribution of the dispersing effect to the strength development is regarded akin as an addition of cement. Based on this premise, the clay–water/cement ratio hypothesis for blended cement admixed clay is proposed for analyzing and assessing the strength development. Even with the difference in water content, cement content and ash content, the blended cement admixed clay samples having the same clay–water/cement ratio, w_c/C possess practically the same stress–strain response and strength. The relationship among strength, clay–water/cement ratio, and curing time for the blended cement admixed Bangkok clay is finally developed and verified. It is useful to assess the strength at any curing time wherein water content, cement content, and ash content vary over a wide range by using the test result of a single laboratory trial. For the economic mix design (the most effective dispersing effect), an addition of 25% ash is recommended. It can save on the input of cement up to 15.8%.     

Preparation of a poly(L-lactide-co-caprolactone) copolymer using a novel tin(II) alkoxide initiator and its fiber processing for potential use as an absorbable monofilament surgical suture

A poly(L-lactide-co-caprolactone) copolymer, P(LL-co-CL), of composition 75:25 mol% was synthesized via the bulk ring-opening copolymerization of L-lactide and ε-caprolactone using a novel bis[tin(II) monooctoate] diethylene glycol coordination-insertion initiator, OctSn-OCH₂CH₂OCH₂CH₂O-SnOct. The P(LL-co-CL) copolymer obtained was characterized by a combination of analytical techniques, namely nuclear magnetic resonance spectroscopy, gel permeation chromatography, dilute-solution viscometry, differential scanning calorimetry, and thermogravimetric analysis. For processing into a monofilament fiber, the copolymer was melt spun with minimal draw to give a largely amorphous and unoriented as-spun fiber. The fiber's oriented semicrystalline morphology, necessary to give the required balance of mechanical properties, was then developed via a sequence of controlled offline hot-drawing and annealing steps. Depending on the final draw ratio, the fibers obtained had tensile strengths in the region of 200–400 MPa.