GaN and AlGaN high-voltage rectifiers grown by metal-organic chemical-vapor deposition

In this paper, we report the study of the electrical characteristics of GaN and AlGaN vertical p-i-n junctions and Schottky rectifiers grown on both sapphire and SiC substrates by metal-organic chemical-vapor deposition. For GaN p-i-n rectifiers grown on SiC with a relatively thin “i” region of 2 μm, a breakdown voltage over 400 V, and forward voltage as low as 4.5 V at 100 A/cm² are exhibited for a 60-μm-diameter device. A GaN Schottky diode with a 2-μm-thick undoped layer exhibits a blocking voltage in excess of ∼230 V at a reverse-leakage current density below 1 mA/cm², and a forward-voltage drop of 3.5 V at a current density of 100 A/cm². It has been found that with the same device structure and process approach, the leakage current of a device grown on a SiC substrate is much lower than a device grown on a sapphire substrate. The use of Mg ion implantation for p-guard rings as planar-edge terminations in mesageometry GaN Schottky rectifiers has also been studied.     

Moment arms and lengths of human upper limb muscles as functions of joint angles

Modeling of musculoskeletal structures requires accurate data on anatomical parameters such as muscle lengths (MLs), moment arms (MAs) and those describing the upper limb position. Using a geometrical model of planar arm movements with three degrees of freedom, we present, in an analytical form, the available information on the relationship between MAs and MLs and joint angles for thirteen human upper limb muscles. The degrees of freedom included are shoulder flexion/extension, elbow flexion/extension, and either wrist flexion/extension (the forearm in supination) or radial/ulnar deviation (the forearm in mid-pronation). Previously published MA/angle curves were approximated by polynomials. ML/angle curves were obtained by combining the constant values of MLs (defined by the distance between the origin and insertion points for a specific upper limb position) with a variable part obtained by multiplying the MA (joint radius) and the joint angle. The MAs of the prime wrist movers in radial/ulnar deviation were linear functions of the joint angle (R2 > or = 0.9954), while quadratic polynomials accurately described their MAs during wrist flexion/extensions. The relationship between MAs and the elbow angle was described by 2nd, 3rd or 5th-order polynomials (R2 > or = 0.9904), with a lesser quality of fit for the anconeus (R2 = 0.9349). In the full range of angular displacements, the length of wrist, elbow and shoulder muscles can change by 8.5, 55 and 200%, respectively.     

Diagnosis of systemic causes of uveitis; a matter of ophthalmologist and internist

OBJECTIVE: To assess how often the aetiology is established in patients with uveitis, what systemic disease are found and what is the contribution of the internist to the diagnostic process. DESIGN: Retrospective study. SETTING: University Hospital Leiden, the Netherlands. METHOD: From January 1987 to April 1992, 342 patients presented with uveitis. All patients underwent a standard ophthalmological examination. Referral to an internist and individualised laboratory screening followed in patients with recurrent, chronic, bilateral or panuveitis. Recorded were: ophthalmological data, results of laboratory screening, results of analysis by the internist, final diagnosis and presence of systemic disease. RESULTS: 149 (44%) patients were examined by the internist, 18 (5.2%) were seen by another specialist. In 169 (49%) patients a specific diagnosis was made. 74 (22%) had a systemic disease, 74 a primary ocular disease. In 28 (8%) a systemic disease was presumed (5% were HLA-B27 positive, 3% had abnormal laboratory results); 5 (1%) patients had endophthalmitis as a complication of a septic process. CONCLUSION: In approximately 1/3 of the patients with uveitis a systemic disease was found. Examination by the internist tailored to the individual patient is essential in the evaluation of uveitis patients.     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

GELYMAC: a Macintosh application for calculating DNA fragment size from gel electrophoresis migration data

A program called GELYMAC takes data on the distances migrated by DNA fragments in a one-dimensional electrophoretic gel and, using a cubic-spline best-fit of marker fragment distance migrated versus molecular size, calculates the molecular sizes of the fragments. Written in the Rascal (Real-time Pascal) programming language, the program runs on the Macintosh family of microcomputers. Rapid entry of marker and experimental fragment migration data is afforded using a scroll bar system adjacent to a graphic representation of a gel. Output includes tabular listing of the data, graphic cartoons of the gel, and the fragment locations and molecular sizes for individual gel lanes, and the calibration curve used in data computations.     

Clinical significance of psychotherapy for unipolar depression: A meta-analytic approach to social comparison.

[Correction Notice: An erratum for this article was reported in Vol 55(3) of Journal of Consulting and Clinical Psychology (see record 2008-10745-001). The data presented in Table 2 were incorrect because a row and a column were inadvertently omitted. The corrected Table 2 appears in the erratum.] This study used meta-analysis to study the clinical significance of psychotherapy for symptoms of unipolar depression. The following questions were addressed: How similar is the posttherapy adjustment of depressed adults to that of nondepressed adults? Is this adjustment maintained at follow-up? What dimensions of treatment, therapists, or design are associated with clinical significance? Using the Beck Depression Inventory (BDI), we calculated composite BDI norms from 28 published studies. Sixty effect sizes (from 31 outcome studies utilizing the BDI) were calculated. The results indicated that psychotherapy produces outcomes that have moderate clinical significance and that are well-maintained at follow-up, that individual therapy is associated with greater clinical significance than group treatment, and that type of therapy is not related to improvement. Alternative approaches for operationalizing clinical significance as the return of individuals to normal levels of functioning are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)