Use of radial forces for fault detection in tapping

A model-based method for fault detection in tapping based on torque and radial forces is proposed. The method allows the identification of faults typical of a tapping operation including axial misalignment, tap runout, tooth breakage both singly and together. The validation experiments have been run on aluminum 356 workpieces for different combinations of process faults. Results have shown that the model predictions are in good agreement with the experimental radial force and torque signals under various fault conditions.     

Lean philosophy: implementation in a forging company

This research addresses the implementation of lean philosophy in a forging company with a focus on radial forging production flow lines. Here, the prime motive is to evolve and test several strategies to eliminate waste on the shop floor. In this research, a systematic approach is suggested for the implementation of lean principles. This paper describes an application of value stream mapping (VSM). Consequently, the present and future states of value stream maps are constructed to improve the production process by identifying waste and its sources. Furthermore, Taguchi’s method of design of experiments is pursued here to minimize the forging defects produced due to imperfect operating conditions. A noticeable reduction in set-up time and work-in-process (WIP) inventory level is substantiated. Finally, we conclude with a discussion of managerial implications and the future scope of research.     

CAD on geocomposite vertical strip drains

In recent years, an increasing need has arisen for various types of construction on sites underlain by soft cohesive soils. In such cases, some methods of soil improvement are usually required to provide adequate bearing capacity and tolerable postconstruction total and differential settlements. These goals often may be achieved by precompression or preloading the site prior to construction. Precompression and preloading are frequently used in combination with vertical drains, especially in very thick soft deposits, otherwise the time required for consolidation may be unacceptably long or the instability of the foundation may be a serious concern. Therefore, the vertical geocomposite (jute and coir) drain may be used to accelerate the settlement of soil thereby making the site available for use in the shortest time. The computer program and the design chart for determining the spacing between geocomposite drains are presented. This technique is generally useful for embankment construction, tank foundation, underwater construction and landfill areas. Two projects (Haldia in West Bengal and Vashi Station Complex in Bombay) have utilized the application of geocomposite drains reported in this paper.     

Does histology influence outcome in childhood Hodgkin's disease? Results from the United Kingdom Children's Cancer Study Group

PURPOSE: Histology has been identified as an important prognostic factor in Hodgkin's disease (HD) in adults. Information regarding the impact of histology on outcome in childhood HD is scarce. This study determines the effect of histology on the overall survival (OS) or progression-free survival (PFS) in a national series of children treated in a standardized manner. PATIENTS AND METHODS: The results of treatment of 331 assessable patients, treated between January 1, 1982 and June 30, 1992, in the United Kingdom Children's Cancer Study Group (UKCCSG) Hodgkin's study I were reviewed to evaluate OS, PFS, and deaths according to stage and histology. Treatment was either involved-field radiation alone (stage IA) or chlorambucil, vinblastine, procarbazine, and prednisolone (ChlVPP) chemotherapy with or without mediastinal radiation. All were clinically staged at diagnosis. RESULTS: Nodular sclerosing (NS) HD was the most common histologic subtype (155 of 331 patients [47%]) and was uniformly distributed through all stages. Lymphocyte-depletion (LD) HD was extremely uncommon (< 1%). Mixed-cellularity (MC) HD had the highest relapse rate, but this was only significant (P < .05) in stage I patients who received local irradiation alone. There was no other statistically significant difference in OS and PFS between the various histologic subtypes. Multivariate analysis for PFS and OS confirmed that stage was the most important prognostic factor and that histology did not have an effect after stratification by stage. CONCLUSION: This study demonstrates that with effective multiagent chemotherapy, histologic subtype does not influence outcome. The high relapse rates in stage I MC subtype indicates that MC HD is biologically aggressive and systemic treatment with or without local irradiation may be indicated. The high relapse rate in stage IV patients appeared to be independent of histology.     

One-step oxidation of cyclohexane to adipic acid

Liquid-phase oxidation of cyclohexane with Co(III) catalyst and gaseous oxygen was found to be influenced by reaction temperature, catalyst concentration and the duration. Maximum adipic acid product selectivity (77%) with about 85% cyclohexane conversion was attained at 100°C using catalyst: cyclohexane molar ratio 0·08. Under these conditions more than 80% cyclohexane was converted in the first hour, although selectivity to adipic acid continued to increase for the next 5 h. Cyclohexyl acetate and cyclohexyl monoadipate were identified as important intermediates. This study supports the mechanism proposed by Schultz, J. G. D. and Opchenko, A., J. Org. Chem., 38 (21) (1973) 3729.     

Monitoring of the ballistocardiogram with the static chargesensitive bed

The static charge sensitive bed (SCSB) consists of a sensitive movement detector embedded in a mattress. When a subject rests on the bed, a single electrical signal, containing components reflective of cardiac, respiratory, and body movement related motion, is produced. This paper describes a digital signal processing technique to separate the BCG from the SCSB signal. An evaluation of this algorithm was conducted using recordings from normal volunteers. Comparisons with simultaneously recorded reference signals indicated that the algorithm performed satisfactorily in a laboratory environment.     

Experimental study of composite cold-formed steel C-section floor joists

Twelve large-scale slab specimens and twenty-two companion push-out specimens were tested to study the behavior and capacity of composite slab joists consisting of cold-formed steel C-sections and concrete. Four shear transfer mechanisms, including surface bond, pre-fabricated bent-up tabs, pre-drilled holes, and self-drilling screws, were employed on the surface of the flange embedded in the concrete to provide shear transfer capacity. Results indicated that specimens employed with shear transfer enhancements showed a marked increase in strength and reduced deflection compared with those relying only on a natural bond between steel and concrete to resist shear. Of the three shear transfer enhancements investigated, bent-up tabs provided the best performance at both the strength and serviceability limit states, followed by drilled holes in the embedded flanges. The use of self-drilling screws resulted in the lowest strength increase. The correlation of shear transfer capacity of push-out specimens with the ultimate capacity of large-scale specimens indicated that the average experimental flexural capacity of the slab specimens was approximately 1.16 times the average predicted value based on push-out test results.     

Prediction of the effects on dynamic response due to distributed structural modification with additional degrees of freedom

The aim of this study is to investigate means of efficiently assessing the effects of distributed structural modification on the dynamic properties of a complex structure. The dynamic properties of the modified structure can be determined by experimental testing or numerical simulation, both of which are complex, expensive and time-consuming. Assuming that the original dynamic characteristics are already established and that the modification is a relatively simple attachment, the modified dynamic properties may be determined numerically without solving the equations of motion of the full-modified structure. The frequency response functions (FRFs) of the modified structure can be computed by coupling the original FRFs and a delta dynamic stiffness matrix for the modification introduced. The validity of this approach is investigated by applying it to a cantilever beam to which a smaller beam is attached as modification. The original FRFs were obtained experimentally as well as numerically. The delta dynamic stiffness matrix was determined numerically by modeling the attachment and part of the original structure including the attachment points. The FRFs of the modified beam were then computed. Good agreement is obtained by comparing the results to the FRFs of the modified beam determined experimentally as well as by numerical modeling of the complete modified structure.     

AHW-BGOA-DNN: a novel deep learning model for epileptic seizure detection

Neural Computing and Applications - “Brain–Computer Interface” (BCI)—a real-life support system provides a way for epileptic patients to improve their quality of life. In...     

IR and Raman studies and effect of γ radiation on crystallization of some lead borate glasses containing Al2O3

IR and Raman spectra of glass ceramics based on PbO-Cr₂O₃-B₂O₃glass composition system have been studied. The bands characteristic of BO₃. and BO₄ functional groups are present in all the samples. An incorporation of Al₂O₃(up to 5 mol%) in the initial glass composition considerably changes the glass network structure and relative concentrations of BO₃ and BO₄ groups. The composition 50 PbO-20 Cr₂O₃-25 B₂O₃-5 Al₂O₃(in mol%) reveals a maximum fraction of boron in the BO₄ group. A sample of this composition heat treated at 850° C for 25 h shows a maximum crystallization fraction with Pb₂O · CrO₄ as a prominent crystalline phase. The glasses irradiated with rays inhibit the crystallization into the Pb₂O · CrO₄ phase. They also show relatively smaller thermal conductivity.