Prediction of ultrasonic wave velocity in particleboard and fiberboard

Ultrasonic wave velocities were determined at parallel and perpendicular to manufacturing direction and at the interval angles of 15° in clockwise and counterclockwise directions of particleboard and fiberboard. The experimental results were compared with the predicted values using some empirical formulae such as Hankinson and Jacoby equations. The results showed that the ultrasonic wave velocity were the highest in parallel direction in particleboard and fiberboard and decreases with increase of angle and the lowest values occurred in perpendicular direction. The predicted ultrasonic velocity using Hankinson and Jacoby equations are in close agreement with the measured values. Relationship between ultrasonic wave velocities and particles and fibers angle could be successfully presented by cubic and quadratic regression equations as well.     

A hermetic glass-silicon micropackage with high-density on-chipfeedthroughs for sensors and actuators

This paper describes the development of a hermetic micropackage with high-density on-chip feedthroughs for sensor and actuator applications. The packaging technique uses low-temperature (320°C) electrostatic bonding of a custom-made glass capsule (Corning 7740, 2×2×8 mm³) to fine grain polysilicon in order to form a hermetically sealed cavity. High-density on-chip multiple polysilicon feedthroughs (200 per millimeter) are used for connecting external sensors and actuators to the electronic circuitry inside the package. A high degree of planarity over feedthrough areas is obtained by using grid-shaped polysilicon feedthrough lines that are covered with phosphosilicate glass (PSG), which is subsequently reflown at 1100°C in steam for 2 h. Saline and DI water soak tests at elevated temperatures (85 and 95°C) were performed to determine the reliability of the package. Preliminary results have shown a mean time to failure (MTTF) of 284 days and 118 days at 85 and 95°C, respectively, in DI water. An Arrhenius diffusion model for moisture penetration yields an expected lifetime of 116 years at body temperature (37°C) for these packages. In vivo tests in guinea pigs and rats for periods ranging from one to two months have shown no sign of infection, inflammation, or tissue abnormality around the implanted package     

Intelligent non-linear modelling of an industrial winding process using recurrent local linear neuro-fuzzy networks

This study deals with the neuro-fuzzy (NF) modelling of a real industrial winding process in which the acquired NF model can be exploited to improve control performance and achieve a robust fault-tolerant system. A new simulator model is proposed for a winding process using non-linear identification based on a recurrent local linear neuro-fuzzy (RLLNF) network trained by local linear model tree (LOLIMOT), which is an incremental tree-based learning algorithm. The proposed NF models are compared with other known intelligent identifiers, namely multilayer perceptron (MLP) and radial basis function (RBF). Comparison of our proposed non-linear models and associated models obtained through the least square error (LSE) technique (the optimal modelling method for linear systems) confirms that the winding process is a non-linear system. Experimental results show the effectiveness of our proposed NF modelling approach.     

Theoretical and experimental analyses of rheological,compatibility and mechanical properties of PVMQ/XNBR-g GMA/XNBR/GO ternary hybrid nanocomposites

Iranian Polymer Journal - Effects of graphene oxide (GO) on various properties of rubber hybrid nanocomposites based on PVMQ/XNBR-g-GMA/XNBR (phenyl-vinyl-methyl-polysiloxane/carboxylated nitrile...     

Long‐term water uptake behavior of natural fiber/polypropylene composites

Composites of different natural fibers and polypropylene were prepared and their long‐term water absorption behaviors were studied. Wood flour, rice hulls, newsprint fibers, and kenaf fibers (at 25 and 50% by weight contents) were mixed with polypropylene and 1 and 2% compatibilizer, respectively. Water absorption tests were carried out on injection‐molded specimens at room temperature for 5 weeks. Measurements were made every week and water absorption was calculated. Water diffusion coefficients were also calculated by evaluating the water absorption isotherms. Results indicated a significant difference among different natural fibers, with kenaf fibers and newsprint fibers exhibiting the highest and wood flour and rice hulls the lowest water absorption values, respectively. The difference between 25 and 50% fiber contents for all composite formulations increased at longer immersion times. Water diffusion coefficients of the composites were found to be about 3 orders of magnitude higher than that of pure PP. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Numerical and Experimental Study of an Under-Ground Water Reservoir,Cistern

This article presents experimental and numerical study of an under-ground water reservoir (cistern) during six months operation in a semi-arid region. The cistern with one dome, four windcatchers and a water reservoir is located in Lar, a hot arid city at south of Iran. Outdoor and indoor air temperature and humidity, water temperature in three depths and dome surface temperature were measured using a data logging system. The results show that the average air humidity inside the cistern was almost constant during the experiments but its slight variation during a day follows inside air temperature changes. The inside air temperature was always lower than the ambient temperature and inside and outside average air temperature difference was about 6 °C. The difference was slightly higher in the hot seasons. The water reservoir was also modeled in 2D, axisymmetric and quasi steady numerical simulation for six months of operation. Highly stratified water temperature distribution was observed in the numerical results as well as the experimental measurements.     

Mechanical properties of composites from sawdust and recycled plastics

Mechanical properties of wood plastic composites (WPCs) manufactured from sawdust and virgin and/or recycled plastics, namely high density polyethylene (HDPE) and polypropylene (PP), were studied. Sawdust was prepared from beech industrial sawdust by screening to the desired particle size and was mixed with different virgin or recycled plastics at 50% by weight fiber loading. The mixed materials were then compression molded into panels. Flexural and tensile properties and impact strength of the manufactured WPCs were determined according to the relevant standard specifications. Although composites containing PP (virgin and recycled) exhibited higher stiffness and strength than those made from HDPE (virgin and recycled), they had lower unnotched impact strengths. Mechanical properties of specimens containing recycled plastics (HDPE and PP) were statistically similar and comparable to those of composites made from virgin plastics. This was considered as a possibility to expand the use of recycled plastics in the manufacture of WPCs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3641–3645, 2006     

A bio-inspired gelatin-based pH- and thermal-sensitive magnetic hydrogel for in vitro chemo/hyperthermia treatment of breast cancer cells

Gelatin (Gel)-based pH- and thermal-responsive magnetic hydrogels (MH-1 and MH-2) were designed and developed as novel drug delivery systems (DDSs) for cancer chemo/hyperthermia therapy. For this goal, Gel was functionalized with methacrylic anhydride (GelMA), and then copolymerized with (2-dimethylaminoethyl) methacrylate (DMAEMA) monomer in the presence of methacrylate-end capped magnetic nanoparticles (MNPs) as well as triethylene glycol dimethacrylate (TEGDMA; as crosslinker). Afterward, a thiol-end capped poly(N-isopropylacrylamide) (PNIPAAm-SH) was synthesized through an atom transfer radical polymerization technique, and then attached onto the hydrogel through “thiol-ene” click grafting. The preliminary performances of developed MHs for chemo/hyperthermia therapy of human breast cancer was investigated through the loading of doxorubicin hydrochloride (Dox) as an anticancer agent followed by cytotoxicity measurement of drug-loaded DDSs using MTT assay by both chemo- and chemo/hyperthermia-therapies. Owing to porous morphologies of the fabricated magnetic hydrogels according to scanning electron microscopy images and strong physicochemical interactions (e.g., hydrogen bonding) the drug loading capacities of the MH-1 and MH-2 were obtained as 72 ± 1.4 and 77 ± 1.8, respectively. The DDSs exhibited acceptable pH- and thermal-triggered drug release behaviors. The MTT assay results revealed that the combination of hyperthermia therapy and chemotherapy has synergic effect on the anticancer activities of the developed DDSs.     

Relay-Assisted Wireless Energy Transfer for Efficient Spectrum Sharing in Harsh Environments

International Journal of Wireless Information Networks - With exponential growth in the number of wireless devices and limited available spectrum, the problem of spectrum sharing remains in...