Winding Method to Reduce Vibration and Loss Caused by Fractional Slot of Synchronous Machine

Fractional‐slot windings are widely used in rotating machines in order to improve the output voltage waveform, increase the design flexibility, and gain many other advantages. However, fractional‐slot windings are known to produce different harmonic components such as an even order and/or fractional number of space flux harmonics compared to integral‐slot windings. These harmonics may increase stray losses and cause stator core vibration. This paper describes an analysis of space flux harmonics and proposes new winding methods such as “novel interspersed windings” to reduce these harmonic components. The proposed winding methods were verified by numerical analysis and model tests.     

波形碳纳米管增强复合材料的有效刚度和局部应力的宏微观均质化数值模拟

采用分子动力学方法简化的碳纳米管等效纤维模型,利用具有精确周期性边界条件的均质化理论和宏微观均质化法分析正弦波形非连续碳纳米管的有效刚度和局部应力分布规律.结果表明,纳米增强复合材料的有效刚度和局部应力对碳纳米管的波形非常敏感,碳纳米管稍有弯曲就会导致复合材料有效刚度降低和应力传递能力的下降,为揭示复合材料中碳纳米管的增强机制和改善增强效果提供理论依据.     

Development of –1 MV DC Filter and High‐Voltage DC Measurement Systems for ITER NBI

This paper presents the development results of a ?1 MV dc filter and dc measurement systems for an ITER (International Thermonuclear Experimental Reactor) neutral beam injector (NBI) system. High accuracy of 0.5% and fast responsivity of 3.3 μs, ?3 dB are required for the dc measurement systems: both dc voltage dividers and DCCTs. Circuit design and thermal flow design were carried out to clarify and minimize their effects on the accuracy and responsivity. The validity of the established design was demonstrated by the actual‐product tests; temperature rise of each components fell below the allowable value; inner components of dc filter withstood dc ?1.2 MV; each voltage divider accurately measured the voltage during the dc ?1.2 MV withstand voltage test; the voltage dividers and the DCCTs were adequate to the requirements of responsivity (3.3 μs, ?3 dB).     

Regional noise prediction and management system using remote sensing

Abstract

This paper deals with the prediction and management of regional and environmental noise using remote sensing techniques. Landsat-MSS and -TM data are used to estimate noise pollution by means of a group method of data handling. They estimate ground roughness from the proportion of the area occupied by buildings thus determining the shielding factor of noise propagation on the ground. The noise level predicted by the method presented in this paper showed a satisfactory agreement with that obtained from measurements from various other cases in urban areas.     

A LRT Control Method Using Sensor Information in Distribution Systems with a Large Amount of PVs and EVs

It is of prime importance to maintain voltage profile within the proper range in distribution systems with a large amount of photovoltaics and electric vehicles (EVs). In particular, there is a possibility that line drop compensation (LDC) logic, which is utilized for the control of load ratio tap transformer (LRT) does not work properly when reverse power flow is included partially. Hence, in this paper, we have developed a new LRT control method based on the sensor information supposing that some section switchgears with sensors are introduced in the future distribution systems. Specifically, the extreme value of voltage profile is estimated by convergence calculation in the section between the section switchgear with sensor and LRT. Moreover, the voltage at the end node can be estimated by LDC method using sensor information of section switchgear. The proposed method was tested using a distribution system model and its effectiveness was shown.     

Effect of deformation mode,dynamic recrystallization and twinning on rolling texture evolution of AZ31 magnesium alloys

In order to obtain quantitative relationship between (0002) texture intensity and hot rolling conditions, conventional rolling experiments on AZ31 magnesium alloys were performed with 20%–40% reductions and temperatures within the range of 300–500 °C. Shear strain and equivalent strain distributions along the thickness of the rolled sheets were calculated experimentally using embedded pin in a rolling sheet. Rolling microstructures and textures in the sheet surface and center layers of the AZ31 alloys were measured by optical microscopy (OM), X-ray diffractometry (XRD) and electron back scatter diffraction (EBSD). Effects of the rolling strain, dynamic recrystallization (DRX) and twinning on the texture evolution of the AZ31 alloys were investigated quantitatively. It is found that the highest (0002) basal texture intensities are obtained at a starting rolling temperature of 400 °C under the same strain. Strain–temperature dependency of the (0002) texture intensity of the AZ31 alloy is derived.     

DISTRIBUTION OF ASCORBATE OXIDASE ACTIVITIES IN THE FRUITS OF FAMILY CUCURBITACEAE AND SOME OF THEIR PROPERTIES

Activities and some other properties of ascorbate oxidases (AAO) from the fruits of family Cucurbitaceae were investigated. The peel and the flesh of seven varieties had activities ranging between 35–56500 units/mg protein and 14–1250 units/mg protein, respectively. AAO from different varieties had a similar pH optimum of around 6–6.5 and a broad pH stability ranging from pH 5 or 6 to pH 10 or 11. These properties appear to be conserved in the AAO's from the family of Cucurbitaceae. The AAO's of melon cv. andes, kinsho and papaya were more susceptible to heat denaturation than AAO from pumpkin.     

Gel-Forming Characteristics and Rheological Properties of Kefiran

A water soluble polysaccharide “kefiran” produced by Lactobacillus kefiranofaciens was examined for its gel-forming and rheological properties. Kefiran (3%) formed gel in the presence of ethanol (4–10%). The gel strength in 8% ethanol was comparable to that of 3% gelatin gel in water. Addition of casein (3%) increased gel strength 1.5–2.0 fold. The unique properties of kefiran may make it a useful food additive.     

Fabrication of particulate reinforced magnesium composites by applying a spontaneous infiltration phenomenon

A new fabrication method of particulate reinforced magnesium matrix composites using a spontaneous infiltration phenomenon was developed. By mixing infiltration agent powder with reinforcement powder, the magnesium melt spontaneously infiltrated into the powder mixture. In this study, pure magnesium, SiO2 and SiC particle (SiCp, 1.2,2,3,4 and 8 m) powders were used as the matrix metal, infiltration agent and reinforcements, respectively. Experiments to clarify the conditions in which the spontaneous infiltration occurred were carried out under pure argon atmosphere at 973 K. Furthermore, the infiltration velocity was measured. Spontaneous infiltration occurred in the 2,3,4 and 8 m SiCp systems. A minimum SiO2 content necessary for spontaneous infiltration existed and it depended on SiCp diameter. Microstructural observation of the composites revealed that SiCp dispersed homogeneously, even though the diameter of SiCp was fine, and MgO and Mg2Si reaction products were observed. During infiltration, a temperature rise was observed, caused by Mg–SiO2 thermit reaction. Consequently, spontaneous infiltration was caused by improvement of wettability between the magnesium melt and SiCp, which resulted from Mg–SiO2 thermit reaction at the infiltration front.     

Enhanced angular current intensity from Schottky emitters

Even though the Schottky emitter is a high‐brightness source of choice for electron beam systems, its angular current intensity is substantially lower than that of thermionic cathodes, rendering the emitter impractical for applications that require high beam current. In this study, two strategies were attempted to enhance its angular intensity, and their experimental results are reported. The first scheme is to employ a higher extraction field for increasing the brightness. However, the tip shape transformation was found to induce undesirably elevated emission from the facet edges at high fields. The second scheme exploits the fact that the angular intensity is proportional to the square of the electron gun focal length [ Fujita, S. & Shimoyama, H. (2005) Theory of cathode trajectory characterization by canonical mapping transformation. J. Electron Microsc. 54 , 331–343], which can be increased by scaling‐up the emitter tip radius. A high angular current intensity (J_Ω∼ 1.5 mA sr⁻¹) was obtained from a scaled‐up emitter. Preliminary performance tests were conducted on an electron probe‐forming column by substituting the new emitter for the original tungsten filament gun. The beam current up to a few microamperes was achieved with submicron spatial resolution.