Two geometrical isomers of linoleic acid: Improved total syntheses

The total syntheses of 9(Z),12(E)- and 9(E),12(Z)-octadecadienoic acids have been carried out. A useful intermediate in both syntheses, 8-bromo-octanoic acid, recently has become available from commercial sources. This compound has been used to expedite the preparation of these isomers. The remaining carbon atoms were derived from propargyl alcohol along with either 1-heptyne or acetylene and 1-bromopentane. Because the overall yield for each sequence was roughly 15% and there were no extraordinary reaction conditions in any of the synthetic steps, the compounds could be prepared readily in multiple gram quantities. The syntheses of the two compounds were supported by data from a variety of spectroscopic techniques.     

Continuous formation of slurry ice by cooling water–oil emulsion in a tube

Water-silicone oil emulsion with an additive, (C₂H₅O)₃SiC₃H₆NH₂, was examined as a heat storage material. A spiral tube used as a heat exchanger was immersed in a low temperature bath and the emulsion was circulated in the tube to make ice continuously. Ice was separated from the ice–liquid suspension in an outlet tank. The amount of formed ice, the temperatures of the inlet and the outlet of the heat exchanger, and the temperatures in the tube wall were measured and the overall heat transfer coefficient and the heat flux through the tube were calculated. Experiments were carried out, varying the flow rate, the temperature of cooling brine, and the thickness of tube wall. The condition under which slurry ice was formed continuously without adhesion of ice to the cooling wall was clarified. Though decrease in the thermal resistance of the tube increased the rate of ice formation or raised the brine temperature, it narrowed the range of the flow rate and of the brine temperature in which slurry ice was formed continuously.     

66/77-kV C-GIS using composite insulation in SF6 gas

A second-generation model of cubicletype gas-insulated switchgear (C-GIS) with composite insulation incorporating SF₆ gas has been developed. The design does not require a gas process in field assembly; it has high reliability and its installation is more rapid; and a further reduction in size is achieved. The design principles are described in detail.     

Micro-computerized tomographic observation of the spinning apparatus in Bombyx mori silkworms

Silkworms and spiders have evolved complex spinning apparatus thought to use highly controlled conditions to optimize protein folding and crystallization to provide a tough fiber. Accordingly, the structure and function of the natural spinning apparatus has been studied with great attention as an interesting piece of biological engineering with potential for mimicry in an industrial process. However it is still not well understood. Here we used Micro-Computerized Tomographic equipment (mCT) to visualize the three-dimensional structure of the spinning apparatus in Bombyx mori silkworms. Multidirectional tomograms obtained by X-ray radioscopy provided valuable information on the detailed arrangement of each muscle of the silk press. It is suggested that the duct in the silk press part plays a part as an extrusion die whose cross-sectional area can be controlled by muscles to optimize applied stresses in the partially gelled silk within its lumen.     

Change in bacterial community during biodegradation of aniline

A modification of the standard electrodiagnostic test was developed in an effort to provide a more sensitive electrodiagnostic evaluation in radial tunnel syndrome. Radial motor nerve latency recordings were obtained in 3 different forearm positions: neutral, passive supination, and passive pronation. The maximal difference in these recordings, the differential latency, in 25 patients with radial tunnel syndrome of greater than 6 months duration (test group) was compared with those in 25 asymptomatic volunteers (control group). Differential latency recordings were obtained in all patients in the test group before and after surgery. Radial nerves that were compressed demonstrated a significantly greater differential latency (0.44+/-0.12 ms) versus controls (0.12+/-0.008 ms). Following radial nerve decompression, differential motor latencies in the test group decreased below control values, demonstrating a resolution of the provoked electrical response with a postoperative differential latency of 0.07+/-0.05 ms. Our results demonstrate the differential motor latency of the radial nerve to be a sensitive electrodiagnostic tool in patients with radial tunnel syndrome. A differential latency of > or =0.30 ms was considered indicative of radial tunnel syndrome.     

In-place Algorithm for Erasing a Connected Component in a Binary Image

Removing noise in a given binary image is a common operation. A generalization of the operation is to erase an arbitrarily specified component by reversing pixel values in the component. This paper shows that this operation can be done without using any data structure like a stack or queue, or more exactly using only constant extra memory (consisting of a constant number of words of O(log n) bits for an image of n pixels) in O(mlog m) time for a component consisting of m pixels. This is an in-place algorithm, but the image matrix cannot be used as work space since it has just one bit for each pixel. Whenever we flip a pixel value in a target component, the component shape is also deformed, which causes some difficulty. The main idea for our constant work space algorithm is to deform a component so that its connectivity is preserved.     

Properties of Va metal-B films prepared by r.f.-sputtering

Ta_100-x B _x alloy films were prepared by r.f.-sputtering in the chemical composition range 45 x 77. Ta_100-x B _x (45 x 58) films consist of the amorphous phase, while the TaB₂ crystal phase was observed in Ta_100-x B _x (66 x 77) films. A remarkable preferred orientation with the (001) plane of TaB₂ parallel to the film surface was observed in Ta₃₄B₆₆. The d.c. electrical conductivity of Ta_100-x B _x (45 x 77) films decreases with increasing boron content in the range 6.7 × 10³ to 1.3 × 10^3–1 cm^–1. The micro-Vickers hardness of Ta_100-x B _x (45 x 77) films was in the range 2200 to 2600 kg mm^–2.     

Preparation of Co-N films by rf-sputtering

Co-N films in the wide compositional range can be prepared by reactive sputtering. Co-N sputtered films consist of one or two phases, such as CoN, Co₂N, Co₃N, Co₄N and -Co. Co₄N phase with a cubic unit cell is observed, and its lattice constant isa = 0.3586 nm. The preferred orientation is observed on the Co-N films, CoN (200) plane, Co₄N (1 1 1) plane and -Co (002) plane parallel to the film surface, respectively. Saturation magnetization _s of Co-N sputtered film decreases from 160 to 1.7 e.m.u. g^–1 with increasing content of N from 0 to 21.7 at%, and coercive force_I H _c is the range of 43 to 5000e at room temperature.     

Stability of protective oxide films in waste incineration environment—solubility measurement of oxides in molten chlorides

Solubility measurements of several oxides in molten NaCl-KCl and NaCl-KCl-Na₂SO₄-K₂SO₄ were conducted in three different levels of basicity. The dissolution behavior of the oxides showed almost the same tendency as that shown by the dissolution behavior of the oxides in molten Na₂SO₄ in literature. In a waste incineration environment, a protective Cr₂O₃ film easily dissolves in molten chlorides as CrO₄²⁻ because pO²⁻ of the molten chlorides tends to have a small value due to the effect of water vapor contained in the combustion gas. From the result of the solubility measurement, the addition of molybdenum and/or silicon was expected to improve the corrosion resistance of alloys. Laboratory corrosion tests confirmed this expectation. However, the scale analysis suggested that the effect of molybdenum could not be explained completely by only the mechanism derived from the result of the solubility measurement.     

Influence of ammonium salt on electrowinning of copper from ammoniacal alkaline solutions

In order to develop an energy-saving copper recycling process from wastes, electrochemical measurements were conducted in ammoniacal alkaline solutions containing Cu(I) ions and an ammonium salt of sulfate, chloride or nitrate. The results of each system were then compared. The polarization measurements suggested that the voltage required for the electrode process is lower in the chloride and nitrate systems than that in the sulfate system. The cathode current efficiency during the copper electrodeposition varied from 39 to 97% and increased with current density in the chloride and sulfate systems. In the nitrate system, the lowest cathode current efficiency of 30% was observed because of nitrate ion reduction. Based on these results, the power consumption required for the electrowinning stage of the copper recycling process was calculated. Among these three systems, the chloride system showed the lowest power consumption of 500 kWh t⁻¹ at the current density of 200 A m⁻², which is about 25% of the conventional copper electrowinning process from a copper sulfate-sulfuric acid solution.