Identification and U-control of a state-space system with time-delay

This article presents a state-space model with time-delay to map the relationship between known input-output data for discrete systems. For the given input-output data, a model identification algorithm combining parameter estimation and state estimation is proposed in line with the causality constraints. Consequently, this article proposes a least squares parameter estimation algorithm, and analyzes its convergence for the studied systems to prove that the parameter estimation errors converge to zero under the persistent excitation conditions. In control system design, the U-model based control is introduced to provide a unilateral platform to improve the design efficiency and generality. A simulation portfolio from modeling to control is provided with computational experiments to validate the derived results.     

智慧标识网络服务机理研究进展及安全性分析

随着互联网规模的不断扩大以及应用场景的多元化,传统网络无法很好地满足新业务的动态多样化需求,因此国内外对未来网络展开了深入研究.本文首先介绍了未来互联网体系架构的研究现状.其次,介绍了具备"三层、两域"特征的智慧标识网络(Smart Identifier NETwork,SINET)体系架构,然后重点阐述了SINET服务机理在服务的命名与解析、路由机制、服务缓存、移动性、传输控制机制、可扩展性、绿色节能等关键技术方面取得的研究进展,并进一步详细分析了SINET服务机理的安全性.最后总结了SINET面临的挑战,对SINET服务机理在大规模场景部署中可能存在的问题做出讨论.     

New Design of Wavelets Based on the Convolution of Compactly Supported Functions with a Rectangular Pulse

Journal of Communications Technology and Electronics - A new design of wavelets based on the convolution of a compactly supported function with a rectangular pulse is proposed and theoretically...     

Nanogrooved carbon microtubes for wet three‐dimensional printing of conductive composite structures

Recent advances in three‐dimensional (3D) printing have enabled the fabrication of interesting structures which are not achievable using traditional fabrication approaches. The 3D printing of carbon microtube composite inks allows fabrication of conductive structures for practical applications in soft robotics and tissue engineering. However, it is challenging to achieve 3D printed structures from solution‐based composite inks, which requires an additional process to solidify the ink. Here, we introduce a wet 3D printing technique which uses a coagulation bath to fabricate carbon microtube composite structures. We show that through a facile nanogrooving approach which introduces cavitation and channels on carbon microtubes, enhanced interfacial interactions with a chitosan polymer matrix are achieved. Consequently, the mechanical properties of the 3D printed composites improve when nanogrooved carbon microtubes are used, compared to untreated microtubes. We show that by carefully controlling the coagulation bath, extrusion pressure, printing distance and printed line distance, we can 3D print composite lattices which are composed of well‐defined and separated printed lines. The conductive composite 3D structures with highly customised design presented in this work provide a suitable platform for applications ranging from soft robotics to smart tissue engineering scaffolds. © 2019 Society of Chemical Industry     

Pressure-induced transparency of MgO,Al2O3, AlN,and cBN ceramics at room temperature

The in situ axial X-ray diffraction patterns of four ceramic powder samples (MgO, Al₂O₃, AlN, and cBN) that were compressed in a diamond anvil cell under uniaxial non-hydrostatic conditions were recorded. The microscopic deviatoric stress as a function of the pressure was determined from the X-ray diffraction peak broadening analysis: the curves increased approximately linearly with the pressure at the initial compression stage and then levelled off under further compression. Pressure-induced transparency was observed in all of the samples under compression, and the pressure at the turning point on the curves of the microscopic deviatoric stress versus pressure corresponded to the pressure at which the samples became transparent. Analysis of the microstructural features of the pressure-induced transparent samples indicated that the compression caused the grains to fracture, and the broken grains bonded with each other. We demonstrated that the ceramics’ pressure-induced transparency was a process during which the grains were squeezed and broken, the pores were close between the grains, and the broken grains were re-bonded under compression.     

Optimized microwave absorption properties by tailoring the morphology of carbon coated TiC nanoparticles by N2 pressure

Increasing the dielectric loss capacity plays an important role in enhancing the electromagnetic absorption performance of materials. It remains a challenge to simultaneously introduce multiple types of dielectric losses in the material. In this work, we show that the atomic and interfacial dipole polarizations can be simultaneously enhanced by substituting N species into both carbon coating layers and bulk TiC lattices of a core-shell TiC@C material. Additionally, substitution of N species results more exposed TiC(111) facets and refines the TiC grain sizes in the bulk material, which is beneficial for enhancing the scattering of the external electromagnetic waves. The maximum reflection loss of the N substituted TiC@C material is measured as ?47.1 dB with an effective absorbing bandwidth of 4.83 GHz at 1.9 mm, which illustrates a valuable way to further tuning the electromagnetic absorption performance of this type of materials.     

基于有限元的低成本塔桅设计及承载能力分析

为研究铁塔公司发布的最新《低成本铁塔标准图集V1.0》的共享改造能力,文章选取了单斜撑三管塔0.65 kN/m2基本风压下的系列塔图,从各塔段的主管应力比和塔顶位移角两个角度,考虑新增天线设备、馈线、爬梯荷载,以及天线设备之间的相互遮挡,利用有限元软件SAP2000对每种塔型进行了常规设计分析和改造增载后的研究分析.由分析结果可知,每种塔型均有可共享改造能力,且随着塔身高度的增加,共享改造的能力逐渐降低.     

Determination of Electrical and Photoelectrical Properties of Schottky Diodes Made Using New Chitin Derivatives Synthesized as Interface Layer

Silicon - 5-(2,4-dichlorophenyl)-2-furoic acid and anthraquinone-2-carboxylic acid were reacted separately with chitin. The synthesized products were characterized by various spectroscopic methods...     

A blind dual color images watermarking based on quaternion singular value decomposition

Multimedia Tools and Applications - With the rapid development of the Internet, the color digital image copyright protection is facing severe challenges. Simultaneously, the color digital images...