Converter configurations and switching frequency for a GTO reactivepower compensator

This paper compares two converter configurations for a multi-10 MVA gate-turn-off (GTO) reactive power compensator (STATCOM) from the viewpoints of converter connection and switching frequency. One is a single-bridge system consisting of a three-phase bridge converter unit and a transformer. Its pulsewidth modulation (PWM) frequency varies from 450 to 1800 Hz, and its line frequency is 50 Hz. The other is a multiconnected converter system consisting of plural, single-, or three-phase converter units and transformers. Its switching frequencies are chosen to be the lowest possible. The evaluated items are harmonic distortion, power loss, GTO utilization factor, and control response. Our simulation study shows that the multiconnected converter system with the lowest switching frequency is superior to the single-bridge system with the higher switching frequency in every case, even when there are severe line faults requiring very quick response. A new control strategy is adopted for obtaining quick response     

Arraying needle-like TiO2 particles in a composite film by applying ac bias and its transmittance anisotropy

In an effort to improve energy-efficient windows, we experimented with a precursor slurry composite by using needle-like TiO₂ particles as the filler in a urethane matrix. Applying dc bias to the slurry failed to array the needle-like particles in the composite and to deposit on the film surface because of electrophoretic movement. However, applying ac bias of ±5 V to the precursor slurry composite for 12 h resulted in the needle-like TiO₂ particles being arrayed in the composite in a direction normal to the film surface. This resulted in an improvement in the energy efficiency of the material through an angular dependence of transmittance in the visible–near-infrared range.     

Analysis of Aftercavity Interaction in European ITER Gyrotrons and in the Compact Sub-THz Gyrotron FU CW-CI

Possibilities of arising of aftercavity interaction are analyzed in the ITER 170?GHz 2?MW coaxial cavity gyrotron and the 170?GHz 1?MW cylindrical cavity gyrotron, as well as in the compact 394.5?GHz low power gyrotron FU CW-CI. Also, the simulations for the gyrotron efficiency in the presence of aftercavity interaction are performed in the cold cavity approximation. Results of the analysis illustrate the subtle interplay between the geometry of the output taper and the profile of the magnetic field.     

Further Characterization of 394-GHz Gyrotron FU CW GII with Additional PID Control System for 600-MHz DNP-SSNMR Spectroscopy

A 394-GHz gyrotron, FU CW GII, has been designed at the University of Fukui, Japan, for dynamic nuclear polarization (DNP)-enhanced solid-state nuclear magnetic resonance (SSNMR) experiments at 600-MHz ¹H resonant frequency. After installation at the Institute for Protein Research (IPR), Osaka University, Japan, a PID feedback control system was equipped to regulate the electron gun heater current for stabilization of the electron beam current, which ultimately achieved stabilization of output power when operating in continuous wave (CW) mode. During exploration to further optimize operating conditions, a continuous tuning bandwidth of approximately 1 GHz was observed by varying the operating voltage at a fixed magnetic field. In the frequency range required for positive DNP enhancement, the output power was improved by increasing the magnetic field and the operating voltage from their initial operational settings. In addition, fine tuning of output frequency by varying the cavity cooling water temperature was demonstrated. These operating conditions and ancillary enhancements are expected to contribute to further enhancement of SSNMR signal.     

Piezoresistivity in Polymer-Ceramic Composites

Composite materials composed of randomly dispersed semiconducting ceramic particles in an insulating polymer matrix show a pronounced change in resistivity with pressure. Different amounts of iron oxide (Fe₃O₄) powder and antimony-doped tin oxide (SnO₂:Sb) powder were dispersed in an epoxy polymer matrix to form pressure-sensitive composites. In each family of materials, an insulator-to-semiconductor transition is observed in agreement with percolation theory. Composites within a certain range of filler content showed substantial piezoresistive effect under both uniaxial and hydrostatic pressure in which sensitivity is controlled by the choice of filler material and the volume fraction. The effect of temperature on the piezoresistance effect was also examined. Piezoresistors made from Fe₃O₄ composites showed larger temperature changes than those filled with Sb-doped SnO₂.     

The Direct Spectroscopy of Positronium Hyperfine Structure Using a Sub-THz Gyrotron

Positronium is an ideal system for research on Quantum Electrodynamics (QED), especially in a bound state. A discrepancy of 3.9 standard deviations has been found between the measured hyperfine structure (Ps-HFS) and the QED predictions. This may be due to the contribution of unknown new physics or common systematic effects in previous measurements, in all of which the Zeeman effect was used. We propose a new method to directly measure the Ps-HFS using a high power gyrotron. We compare two resonators which have been developed to supply sufficient power to drive the direct transition, a Fabry-Pérot resonator and a ring resonator with a diffraction grating. We plan to perform first direct measurement of Ps-HFS within the next six months.     

Development of an active targeting liposome encapsulated with high-density colloidal gold for transmission electron microscopy

Active targeting of the liposome is an attractive strategy for drug delivery and in vivo bio-imaging. We previously reported the specific accumulation of Sialyl Lewis X (SLX) liposome to inflamed tissue in arthritic model mice or tumor-bearing mice. SLX-liposome encapsulation with fluorescent substances allows for the visualization of these liposomes by the time-dependent transvascular accumulation of fluorescent signals in the histological sections. In the present study, we developed a new SLX-liposome encapsulated with colloidal gold for transmission electron microscopic observation. We herein describe the characterization of the colloidal gold-loaded SLX-liposomes and demonstrate its specific targeting to the endothelial cells of tumor blood vessels in tumor-bearing mice.     

Colored Fluorescent Silk Made by Transgenic Silkworms

Silk is a protein fiber used to weave fabrics and as a biomaterial in medical applications. Recently, genetically modified silks have been produced from transgenic silkworms. In the present study, transgenic silkworms for the mass production of three colors of fluorescent silks, (green, red, and orange) are generated using a vector originating from the fibroin H chain gene and a classical breeding method. The suitability of the recombinant silks for making fabrics is investigated by harvesting large amounts of the cocoons, obtained from rearing over 20 thousand silkworms. The application of low temperature and a weakly alkaline solution for cooking and reeling enables the production of silk fiber without loss of color. The maximum strain tolerated and Young's modulus of the fluorescent silks are similar to those of ordinary silk, although the maximum stress value of the recombinant silk is slightly lower than that of the control. Fabrics with fluorescent color are demonstrated using the recombinant silk, with the color persisting for over two years. The results indicate that large amounts of genetically modified silk can be made by transgenic silkworms, and the silk is applicable as functional silk fiber for making fabrics and for use in medical applications.     

Light-Wavelength-Based Quantitative Control of Dihydrofolate Reductase Activity by Using a Photochromic Isostere of an Inhibitor

Photopharmacology has attracted research attention as a new tool for achieving optical control of biomolecules, following the methods of caged compounds and optogenetics. We have developed an efficient photopharmacological inhibitor—azoMTX—for Escherichia coli dihydrofolate reductase (eDHFR) by replacing some atoms of the original ligand, methotrexate, to achieve photoisomerization properties. This fine molecular design enabled quick structural conversion between the active “bent” Z isomer of azoMTX and the inactive “extended” E isomer, and this property afforded quantitative control over the enzyme activity, depending on the wavelength of irradiating light applied. Real-time photoreversible control over enzyme activity was also achieved.