Experimental Thermal Performance Characterization of Flat Grooved Heat Pipes

ABSTRACT

The thermal characterization of aluminum flat grooved heat pipes is performed experimentally for different groove dimensions. Three heat pipes with groove widths of 0.2?mm, 0.4?mm, and 1.5?mm are used in the experiments. The effect of the amount of the working fluid is extensively studied for each groove width. The results reveal that, although all three succeed in dissipating the heat input through the phase change of the working fluid by continuous evaporation and condensation, the effectiveness of the heat transfer increases with reduced groove width. Furthermore, it is observed that there exists an optimum operating point, where the temperature difference between the heating and cooling sections is at a minimum, and the magnitude of this temperature difference is a strong function of the groove width. To the best of the authors’ knowledge, the combined effects of groove dimensions and the amount of the working fluid, from fully flooded to dry, is reported for the first time for aluminum flat grooved heat pipes.     

Partitioning of predominant lipophilic bioactives (squalene, α-tocopherol and β-sitosterol) during olive oil processing

The partitioning of predominant lipophilic olive bioactives (squalene, β-sitosterol and α-tocopherol) in olive oil processing was studied for the first time using common integrated olive milling plant. 7% of the oil and 5% of the squalene present in the olives was lost in the last pomace. β-sitosterol and α-tocopherol, which are mainly concentrated in the seed of the olive fruit, was recovered in virgin olive oil to a lesser extent (66%, 67%) while 10% were lost in last pomace. Thus, the loss of β-sitosterol and α-tocopherol was higher than that of squalene and oil, due to nonrecovered bound forms. 19% of the α-tocopherol and 21% of the β-sitosterol loss was unaccounted for, which can be attributed to degradation of α-tocopherol and incomplete recovery of sterols from the olive and pomace matrices. This study provides a basis for process development studies.     

Production of compounded asphalts of improved quality

Paving-and roofing-grade asphalts were obtained at LUKOIL-Permnefteorgsintez Ltd. by mixing peroxidized asphalt and a number of high-boiling unoxidized petroleum products in certain ratios. The asphalts obtained have improved performance characteristics: high plasticity and low brittleness temperature. __________ Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 2, pp. 26–28, May–June, 2006.     

Nanoscale Crystallization in Amorphous Fe–P–Mn Alloys

Mössbauer effect measurements and physicochemical analysis demonstrate that annealing of amorphous Fe–P–Mn alloys leads to the formation of a nanocrystalline structure.     

A biochar from casein and its properties

A biochar was prepared by pyrolysis of casein. A helium and mercury porosimeter were used to measure the true and apparent densities of the chars respectively, elemental and IR analysis were used to characterize the chemical composition of char. A SEM was used to observe the char surfaces in order to verify the presence of porosity. The biochar has 9.02% of nitrogen, content of porosity is 20%. The experimental results show that it is possible to prepare chars with relatively high porosity from casein for the further preparation of activated carbon.     

高分子表面活性剂对超声辐照下苯乙烯乳液聚合的影响

在超声辐照引发苯乙烯乳液聚合中加入一种新型的以羧甲基纤维素为基础的高分子表面活性剂(CMC—A9)，讨论了高分子表面活性剂对反应动力学的影响。实验表明，超声辐照下初级自由基并非由通常认为的高分子表面活性剂产生，而是十二烷基硫酸钠在超声辐照下断裂，产生自由基。通过对反应动力学的研究，发现超声辐照下乳液聚合机理不同于常规乳液聚合，聚合反应过程只有两个阶段，即加速期和减速期，不存在恒速期。加入CMC—A9高分子表面活性剂，可以在较短的时间内和较低的超声功率下达到较高的单体转化率。     

Increasing the service properties of weld joints by electrohydroimpulse treatment

Known examples of the positive influence of electrohydroimpulse treatment on the quality of weld joints of various steels, particularly including an increase in their long-term and cyclic strength and also corrosion resistance, are analyzed. It is shown that in this case there is a reduction in residual macro- and micro-stresses and also a change in the parameters of the dislocation structure of the joint metal in the direction of stabilization of it.Translated from Problemy Prochnosti, No. 4, pp. 119–123, April, 1996.