Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

Which vessel is more important in the supercharged flap--artery, vein, or both? An experimental study

The supercharged flap is one which is expected to attain better survival, by anastomosing the distal vessels of the flap to the recipient vessels. An experimental study is reported to determine whether the vessel to be anastomosed should be an artery, a vein, or both. The authors advise anastomosing an artery and a vein, but they believe that arterial inflow is more important than venous drainage.     

Non-linear current–voltage characteristics related to native defects in SrTiO3 and ZnO bicrystals

SrTiO₃ and ZnO bicrystals with various types of boundaries were fabricated in order to examine their current–voltage characteristics across single grain boundaries. Their grain boundary structures were also investigated by high-resolution transmission electron microscopy. In Nb-doped SrTiO₃, electron transport behaviors depend on the type of boundaries. Random type boundaries exhibit highly non-linear current–voltage characteristics, while low angle boundaries show a slight non-linearity. On the contrary, undoped ZnO does not exhibit non-linear current–voltage characteristics in any type of boundaries including random ones. It is suggested that the differences observed in current–voltage properties between the two systems are mainly due to the difference in the accumulation behavior of acceptor-like native defects at grain boundaries. A clear non-linearity is obtained by means of Co-doping even for the highly coherent Σ1 boundary in a ZnO bicrystal. This is considered to result from the production of acceptor-like native defects by Co-doping.     

A Unified Approach to Submicron DC MOS Transistor Modeling for Low-Voltage ICs

A unified single-equation approach for the MOS transistordrain current modeling for energy-efficient submicron MOS circuitsis presented. Instead of three sets of separate equations forthe triode, saturation, and weak inversion regions, only a continuousexpression which is valid to describe the behavior of drain currentand the derivatives in all operation regions can be realizedby using a combination of hyperbola, sigmoid, and interpolationmethods. The model expression can predict accurate results forthe current, output conductance, and transconductance with continuousand smooth characteristics. The simulation results agree wellwith experimental data.     

Changes in Aging Behavior and Defect Structure of Yttria-Fully-Stabilized ZrO2 with Sc2O3 Doping

Methods of suppressing decreased conductivity in 8 mol% Y₂O₃-stabilized–92 mol% ZrO₂ (8YSZ) with aging were investigated. Different amounts of Sc₂O₃ were doped into 8YSZ. The electrochemical properties of Sc₂O₃-doped 8YSZ were measured, and the microstructural and local structural changes were characterized. The present results indicate that an appropriate amount of Sc₂O₃ doping, 3 or 4 mol%, effectively suppresses decreased conductivity with aging in 8YSZ.     

A new method for power generation planning and problems of uncertainty

This paper presents a new method for power system planning which considers uncertainties of various system parameters as a part of the criterion function. The criterion function involves both the expected values of total system costs and the cost variances of different power plants. Previously, the authors proposed that these cost variances be evaluated from the existing power system plans in the form of the solutions to the inverse optimization problem, and then applied this procedure to the planning of power systems in Japan. However, because of the correlation between fuel and facility costs, the cost variances could not be determined as specific values. Here, to overcome this difficulty, the authors now introduce hydropower plants into the model as the so-called nonrisky elements and focus on the expenditure shares rather than the plant capacity shares. As a result, more reasonable results are obtained. This improved methodology is applied and the derived cost variances are shown. Further, using the resultant cost variances, the authors make Pareto-optimal power generation plans and demonstrate also the robustness of the method to price fluctuations.     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

A shell for signal interpretation expert systems

System monitoring and diagnosis through signal interpretation are important tasks in many engineering fields. Although monitoring or diagnosis expert systems help human experts a lot, it is not so easy to build a signal interpretation expert system. We have developed two expert systems for speech signal processing. The close analysis of the two systems revealed common functions and modules applicable to wide range of signal interpretation problems. On the basis of the experience, we have developed a shell for signal interpretation expert systems named SSI. In order to evaluate SSI, we also developed two expert systems by using it and obtained satisfactory results. This paper describes the design philosophy and architecture of SSI together with some examples.