On the performance of band-limited asynchronous DS-CDMA over nakagami-m channels

In this paper we investigated the BER performance of DS-CDMA using various chip-waveforms, which include three time-limited chip-waveforms and two band-limited chip-waveforms. Closed-form formulae were derived for evaluating the achievable bit-error rate performance with the aid of the standard Gaussian approximation, when communicating over a Nakagami-m channel. The time-limited waveforms impose a low implementational complexity, since they maybe over sampled and read from a look-up table. However, they are outperformed by the frequency-domain raised-cosine waveform as well as the optimum waveform specifically designed by Cho and Lehnert for achieving the lowest possible bit error rate     

Synthesis and characterization of biocompatible hydroxyapatite coated ferrite

Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own but is stabilized with small substitution of La. Hexaferrite of chemical composition (CaO)_0.75(La₂0₃)_0.20(Fe₂O₃)₆ was prepared using citrate gel method. Hydroxyapatite was prepared by precipitating it from aqueous solution of Ca(NO₃)₂ and (NH₄)₂HPO₄ maintaining pH above 11. Four different methods were used for coating of hydroxyapatite on ferrite particles. SEM with EDX and X-ray diffraction analysis shows clear evidence of coating of hydroxyapatite on ferrite particles. These coated ferrite particles exhibited coercive field up to 2 kOe, which could be made useful for hysteresis heating in hyperthermia. Studies by culturing BHK-21 cells and WBC over the samples show evidence of biocompatibility. SEM micrographs and cell counts give clear indication of cell growth on the surface of the sample. Finally coated ferrite particle was implanted in Kasaulli mouse to test its biocompatibility. The magnetic properties and biocompatibility studies show that these hydroxyapatite coated ferrites could be useful for hyperthermia.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

关于天然气水合物钻采工艺技术进展的研究

目前全球正面临着前所未有的能源危机，天然气水合物由于储量大、能量密度高而将成为一种诱人的新型能源。天然气水合物主要存在于冻土带和海洋，在地下处于低温和高压状态，以现有的技术，钻井和开采都存在很大的困难。简要介绍了天然气水合物的性质及储量，阐述了天然气水合物钻井的六个挑战及目前国外天然气水合物的两种钻探方法；同时阐述了以热力法、降压法和化学试剂注入法为主的天然气水合物开采方法，并针对天然气水合物钻采技术现状指出了下一步的研究方向。     

应用时频分析方法辨识时变系统的模态参数

应用Gabor展开及Hilbert变换进行时变线性系统模态参数的辨识。利用非平稳信号的Gabor变换将结构响应信号表示在时频面上，并通过Gabor展开重构分离模态分量，建立每一阶模态的时变线性模型。对单模态时变线性模型应用Hilbert变换来辨识随时间变化的模态频率和阻尼。通过对刚度和阻尼慢变的两自由度系统模态参数的仿真辨识验证辨识方法的有效性。仿真结果表明：本文方法为时变线性系统的模态参数辨识提供了一条新的途径。     

微流控分析芯片制作中的低温键合技术

微流控分析芯片制作方法的研究是微流控分析的基础。制作性能良好的微流控分析芯片时,基片与盖片的键合技术十分重要。本文针对近年来发展迅速的低温键合技术,对各种方法进行了评价,并对其发展前景进行了展望。     

数值试井在白6-2井测试资料分析评价中的应用

数值试井是在近来发展的一项新的试井解释技术，具有处理非均质，复杂边界油气藏问题的优点，弥补了常规解析试井技术的不足。运用数值试井解释技术，结合动、静态资料，通过对白6-1断块白6-2井测试资料的综合分析评价，确定了储层渗流参数，落实了该气藏的边界情况，为该断块下一步开发提供可靠依据。     

用CMOS工艺实现VSR光电集成接收机的途径

介绍了10Gbit／s速率的甚短距离光传输系统VSR(Very Short Reach)中的接收机。分析了几种有希望用于VSR系统的CMOS工艺兼容的光电探测器。提出用CMOS电路实现VSR光电集成(OEIC)接收机的可能性和实现方法。     

Evaluating the impact of CASE: an empirical comparison of retrospective and cross-sectional survey approaches

The purpose of this paper is to evaluate two methods of assessing the productivity and quality impact of Computer Aided Software Engineering (CASE) and Fourth Generation Language (4GL) technologies: (1) by the retrospective method; and (2) the cross-sectional method. Both methods involve the use of questionnaire surveys. Developers' perceptions depend on the context in which they are expressed and this includes expectations about the effectiveness of a given software product. Consequently, it is generally not reliable to base inferences about the relative merits of CASE and 4GLs on a cross-sectional comparison of two separate samples of users. The retrospective method that requires each respondent to directly compare different products is shown to be more reliable. However, there may be scope to employ cross-sectional comparisons of the findings from different samples where both sets of respondents use the same reference point for their judgements, and where numerical rather than verbal rating scales are used to measure perceptions.