Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Fiber-optic devices for local area network application

Recent developments on fiber-optic devices are reviewed from the local area network (LAN) application viewpoint. Future technical trends are also discussed, along with current research activities. In local area network systems, low device cost and easy maintenance or maintenance-free devices are especially required. Light sources and photodetectors suitable for the systems are described. InGaAsP/InP light emitting diodes can cover a broad application field, up to a gigabits per second super high-speed network region. Optical passive devices, which include branching couplers, switches and connectors, are mentioned as essential components. Compact transmitter/receiver module technology is a key factor in realizing optical-fiber local area network systems. An example of 200-Mbit/s transmitter/receiver module is reported.     

Use of a YAP1 overexpression cassette conferring specific resistance to cerulenin and cycloheximide as an efficient selectable marker in the yeast Saccharomyces cerevisiae.

Drug-resistance markers for yeast transformation are useful because they can be applied to strains without auxotrophic mutations. However, they are susceptible to technical difficulties, namely lower transformation efficiency and the appearance of drug-resistant mutants without the marker. To avoid these problems, we have constructed a phosphoglycerate kinase (PGK) promoter-driven YAP1 expression cassette, called PGKp-YAP1. Yeast cells containing PGKp-YAP1 were resistant to cycloheximide, a protein synthesis inhibitor, and also to cerulenin, a fatty acid synthesis inhibitor, but not to other drugs tested. The transformation efficiency of PGKp-YAP1 using cerulenin selection was comparable to that using a URA3 auxotrophic marker when low concentrations of cerulenin were used. Non-transformed drug-resistant colonies did appear on the low-concentration cerulenin plates. However, these non-transformed colonies could easily be identified, based on their cycloheximide sensitivity and/or their resistance to aureobasidin A to which the transformants were sensitive. Therefore, the dual drug resistance of PGKp-YAP1 could be used as an effective selection for PGKp-YAP1 recipient cells. The PGKp-YAP1 marker was used to disrupt the LYS2 gene and to transform an industrial yeast strain, indicating that this marker can be used for efficient and reliable gene manipulations in any Saccharomyces cerevisiae strain.     

Adaptive control-based high-performance drive system implementation of traveling-wave-type ultrasonic motor

In recent years, ultrasonic motors (USM) as new actuators have attracted special interest. Several kinds of constructions and characteristics of USMs have been reported so far. Of these USMs, a traveling wave-type USM has many characteristics such as: high torque in the low-speed range, large holding torque based upon frictional force, flexible free forms, compactness in size and low magnetic noise. In practice, an inherent mechanical resonant frequency and a velocity amplitude of USM are changed largely according to operating temperature due to frictional drive, load disturbance torque, and applied voltage levels. Therefore, it is necessary to develop a new control system which solves these items and always supplies the required power with high efficiency and high performance in the practical applications. This paper proposes mainly a new sensorless high-performance control scheme of an inverter-fed ultrasonic motor, which is based on a control system technology with two feedbacks incorporating automatic resonant frequency tracking and constant velocity amplitude control strategies. This control system is realized in terms of a high-frequency chopper and a two-phase series/parallel resonant inverter. The experimental results are demonstrated and discussed compared with the theoretical ones.     

Application of microwaves and millimeter waves for thecharacterization of teeth for dental diagnosis and treatment

This paper presents applications of microwaves and millimeter waves for the characterization of teeth. This is done by measuring the complex permittivity over the frequency range from 0.04 to 40 GHz. These measurements have revealed that dental caries are significantly more lossy to microwaves and millimeter waves than the healthy tooth, and this difference can be used for dental diagnosis. The experimental results have been confirmed by using the finite-difference time-domain (FDTD) method. In addition, millimeter-wave heating of the lossy dental caries can be used as a sterilization treatment. It is concluded that millimeter waves can be used for dental medical diagnosis as well as dental medical treatment     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

An investigation of induced voltages to an underground gas pipeline from an overhead transmission line

This paper investigates induced voltage characteristics from an overhead transmission line by applying a method of modeling of induced voltages proposed by the authors. EMTP simulation results obtained by the modeling method agree with analytical results obtained from a well‐known formula. The induced voltages are significantly dependent on the configuration of the overhead line. A horizontal line induces the largest voltage in a gas pipeline, and the voltage induced by a vertical twin‐circuit line is about 20% smaller than that induced by a vertical single‐circuit line. The method is applied to a real pipeline system and the simulation results show reasonable agreement with field test results. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 43–51, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20465