Anti beta 2glycoprotein I antibodies and lupus anticoagulant in patients with recurrent pregnancy loss: prevalence and clinical significance

Over 2000 electrocution deaths were identified among U.S. construction workers from 1980 to 1991, with the highest mean annual crude mortality rate (2.5 per 100,000 people), and second highest mean age-adjusted rate (2.7 per 100,000 people) of all industries. Although the crude fatality rates showed a downward trend, construction workers are still about four times more likely to be electrocuted at work than are workers in all industries combined. Nearly 40% of the 5083 fatal electrocutions in all industries combined occurred in construction, and 80% were associated with industrial wiring, appliances, and transmission lines. Electrocutions ranked as the second leading cause of death among construction workers, accounting for an average of 15% of traumatic deaths in the industry from 1980 to 1991. The study indicates that the workers most at risk of electrical injury are male, young, nonwhite, and electricians, structural metal workers, and laborers. The most likely time of injury is 11 a.m. to 3 p.m. from June to August. Focusing prevention on these populations and characteristics through better methods of worker and supervisor electrical safety training, use of adequate protective clothing, and compliance with established procedures could minimize the average annual loss of 168 U.S. construction workers.     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

Interplay of YBCO and Embedded 211 Particles in Melt-Textured YBCO Superconductors

Local orientations of superconducting YBa₂Cu₃O _x (123) and embedded Y₂BaCuO₅ (211) particles within bulk, melt-textured 123 samples are studied on a local scale by means of electron backscatter diffraction (EBSD). The embedded Y₂BaCuO₅ (211) particles do not show any preferred texture, but their presence within the 123-matrix alters the growth of the 123-phase, independent of the orientation. EBSD enables to analyse the interactions between the 123- and 211-phases in detail.     

Time-dependent deformation in an enhanced SiC/SiC composite

Time-dependent deformation in an enhanced SiC/SiC composite has been studied under constant load at high temperatures of 1200 °C, 1300 °C, and 1400 °C. Creep damage evolution was evaluated by a Young’s-modulus change of partial unloading and microscopic observation. The addition of the glassy phase in the matrix is very effective for protecting the composite from oxidation. The transient creep is dominant in creep life at all the temperatures. An empirical equation is proposed to describe creep behavior of the composite. It is found that creep activation energy increases with creep time at stresses lower than matrix cracking stress, but the activation energy remains constant at stresses higher than the matrix cracking stress. The creep strain rate of the composite is considered to be controlled by creep of fibers based on examining the time, strain, stress, and temperature dependencies of creep strain rates.     

Correlations Among Maximum Likelihood and Weighted/Unweighted Least Squares Estimators in Factor Analysis

The asymptotic correlations among maximum likelihood (ML) and various least squares (LS) estimators in factor analysis are derived. The LS estimators include the unweighted (ULS) and weighted estimators for unstandardized variables and the ULS estimators for standardized variables. The derived formulas cover the cases with restrictions on parameters. Numerical examples with simulations are provided to confirm the accuracy of the formulas and the influence of scales on the asymptotic correlations.

     

Radiation tolerance for the SMASH-series front-end chips for a silicon micro-strip detector

The radiation tolerance for prototype front-end chips designed for a silicon micro-strip detector was examined with a ⁶⁰Co irradiation source to establish an allowable range of the radiation dose. The irradiated front-end chips were SMA²SH-64A, a 64-channel preamplifier array; SMA²SH-1, a single-channel preamplifier circuit with a comparator; and Control-C, a digital-control chip for the preamplifiers.     

Dyeing properties of oxygen low-temperature plasma-treated wool and nylon 6 fibres with acid and basic dyes

Wool and nylon 6 fibres treated with oxygen low-temperature plasma were dyed with acid and basic dyes. Despite the increase of electronegativity of the fibre surface caused by the plasma treatment, the rate of dyeing of wool was increased with both dyes, while that of nylon 6 was decreased with the acid dye and increased with the basic dye.     

Effective thermal conductivity of compressed woods

Compression is one solution to improve the strength of softwoods. The effective thermal conductivities of compressed Japanese cedars (cryptomeria japonica), which were compressed in the radial direction of the wood, were measured. Both the effective thermal conductivities in the tangential and fiber directions increase proportionally to the density increment due to the compression. However, the thermal conductivity in the radial direction (compression direction) increases slightly with the density increment. Numerical computations were conducted to explain the characteristics of thermal conductivity in the radial direction by using a microscopic heat conduction model for the compressed wood. The numerical results were compared with the measured values. And the physical mechanism of the heat conduction in the compressed woods is discussed.     

Development of a single loop EPR test method and its relation to grain boundary microchemistry for alloy 600

A single loop electrochemical potentiokinetic reactivation test method has been developed for alloy 600 that produces good passivation on all the surfaces, good etching during the reactivation scan and no appreciable pitting. It is able to quantify and discriminate between samples with a wide range of degree of sensitization. The Pa value correlates well with the minimum level of chromium in the depletion regions at the grain boundaries. It has been shown that the width of the attacked regions is much larger than the width of chromium depletion regions and it does not show any direct correlation with either depth or width or with a volume parameter of chromium depletion regions. It has been shown that the chromium carbides are not attacked during the test and that the intragranular regions attacked during the test are the sites of chromium carbides in the grain matrix. A modified Pa parameter is shown to be sensitive down to 7.5 wt% chromium in the depletion regions and indicates that the intragranular carbides have shallower depletion profiles than those at grain boundaries. Comparison of the results of the single loop and the double loop tests showed a good correlation.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.