Structural,optical and electronic characteristics of Cu and Mg-doped nano MnS sample prepared by molten salt solid state reaction

Journal of Materials Science: Materials in Electronics - Nano Mn0.95M0.05S (M ≡ Cu, Mg) samples were produced using molten salt solid state reaction method. Rietveld analysis of X-ray...     

In situ characterization of building materials for propagation modeling: frequency and time responses

We propose original data processing methods for the dielectric characterization of frequency-dependent reflection coefficients of construction materials considering a very wide frequency band. Two types of approaches have been developed to obtain, from spectral measurements, estimates of the equivalent complex permittivity versus frequency or reconstruction of the impulse response. In particular, high-resolution (HR) algorithms based on the matrix pencil method have been used in an original way to identify wave multipath inside a sample. Both approaches have been used for the characterization of different types of building materials. A database of dielectric responses of materials is under construction in order to provide the deterministic propagation simulator with the characteristics of building materials.     

Modified tracking loop for DS spread spectrum systems

A nonconventional pseudo-noise (PN) code tracking loop for direct sequence (DS) spread spectrum systems is presented. It solves problems of component imbalance while maintaining hardware simplicity.<>     

Electrochemical Behaviour of Al, Al—In and Al–Ga–In Alloys in Chloride Solutions Containing Zinc Ions

The electrochemical behaviour of Al, Al—In and Al–Ga–In alloys in 0.6 m NaCl solutions with and without Zn²⁺ was investigated. The study was performed by means of open circuit potential, potentiodynamic polarization, potentiostatic current-time and electrochemical impedance spectroscopy measurements as well as by SEM-EDAX examination. It was found that the Al—In alloy exhibits the highest negative open circuit potential in 0.6 m NaCl and the corrosion resistance of the tested electrodes decreases in the following order: Al > Al–Ga–In > Al—In. The greater activity of the Al—In alloy was interpreted on the basis of the autocatalytic attack by indium. The potentiostatic current–time measurements in Zn²⁺ containing electrolyte at potentials above the pitting potential revealed that Zn²⁺ has an insignificant influence on the Al electrode, while it enhances the corrosion of the Al–Ga–In alloy and improves the attack morphology of the Al—In alloy. Furthermore, the impedance spectra recorded under open circuit conditions showed a decrease in the polarization resistance of Al—In and Al–Ga–In alloys in presence of Zn²⁺ indicating the activating effect of Zn²⁺ ions.     

Evaluation of Al and Some of Its Alloys as Anode Materials vs γ-MnO2 as Cathode Material and Ore Produced γ-MnO2 vs Zn Anode in KOH Solution

In this study electrochemical performance of Al and some of its alloys (Al-Zn, Al-Mg and Al-Mn) anodes vs MnO2 cathode were carried out in alkaline solution. The results show that the Al-Zn alloy anode has the best cell capacity among the other alloys. Cell capacity values go in the order Al-Zn＞Al-Mg＞Al＞Al-Mn. This result is probably related to the nature of passive films formed on the surface of the alloys which examined by scanning electron microscopy (SEM). SEM morphologies of Al and its alloys showed coarse grains of passive films formed on the surface of these anode materials while Al-Mn morphology shows a needle-like structure.Electrolytic manganese dioxide (EMD) produced by electrodepositing on platinum anode from liquor resulting from reduction of low grade pyrolusite ore (β-MnO2) by sulfur slag was characterized as cathode in alkaline Zn-MnO2 batteries. Ore produced sample (EMD1) was performed well in comparison with EMD standard (EMD2) (commercial battery grade electrolytic manganese dioxide, TOSOH-Hellas GH-S). SEM morphology of Zn anode after cell reaction was carried out and showed that Zn anode has fine grains of passive film on its surface.     

Photophysical Parameters of Functional Transparent Polymethyl-Methacrylate/Double-Walled Carbon Nanotubes Nanocomposite Sheet Under UV-Irradiation

Polymethyl-methacrylate (PMMA)/double-walled carbon nanotubes DWCNTs was prepared by using casting technique and studying with different spectroscopic techniques. UV/Vis spectral analysis shows that, the transmittance reaches to 92 % for blank PMMA and decreases to 87 % for PMMA doped with 0.01 DWCNTs composite. The calculated refractive index and absorption coefficient increase, while the estimated values of Urbach energy decreased after embedding CNT into PMMA matrix. The optical band gap values were observed to vary slightly with doping amount. Photoluminescence (PL) spectra show that there is no shift in the emission peak position upon doping with CNTs, but PL intensity is enhanced.     

Development of testing procedure for ceramic disc filters

Small-scale laboratory tests for sizing and designing disc filters are typically performed by using leaf test equipment. Although the basic tests are fairly simple and quick, the accuracy and repeatability of the results may be poor due to various reasons. In addition to errors caused by variations in the structure of the equipment, also the skills and experience of the person performing the tests is of great importance. This paper introduces an experimental study carried out for defining the most important sources of errors in these kinds of laboratory tests and for estimating their influence on the final test results. The results obtained in this study were utilized for designing an improved version of the test equipment and also for creating a standard procedure for performing the tests. The results acquired with the small-scale laboratory tests were in good agreement with the performance results obtained from full-scale ceramic disc filters operating in industrial processes.     

In situ STM and EQCM studies of tantalum electrodeposition from TaF5 in the air- and water-stable ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide

The electroreduction of 0.5 M TaF₅ on Au(1 1 1) and on polycrystalline gold substrates was investigated at room temperature in the ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide, [Py_1,4]TFSA, by cyclic voltammetry, in situ scanning tunneling microscopy (STM) and electrochemical quartz crystal microbalance (EQCM). The electrochemical reduction of TaF₅ in the employed ionic liquid occurs in several steps. The first redox process is attributed to the reduction of TaF₅ to TaF₃, which likely occurs in the solution, as EQCM indicates no mass change. The electrodeposition of tantalum occurs only in a very narrow potential window and is preceded by the formation of various non-stoichiometric tantalum subhalides. Attempts to deposit micrometer thick tantalum layers at room temperature fail, presumably because of kinetic reasons.     

CD-ROM patent archives: will the Internet consign them to history?

The World Wide Web has provided millions of people with rapid access to a huge number of patent specifications. They are generally either free of charge or require only relatively small fees. After the launch of big projects like ESP@CENET^® by the EPO and the initiatives of other patent offices, many people are convinced that this is the end of the established CD-ROM archives. This article looks at how CD-ROM archives were developed to fulfil the demands of a large company, reviews the latest developments and poses the question where do we go from here?