Impact Fracture of Thermally Tempered Glass Helicopter Windshields

In-service fracture of helicopter windshields was studied. Simulated catastrophic fracture tests were conducted by firing alumina and steel spheres onto stationary tempered and as-received glass panels. The results were studied by Hertzian analysis and modified Auerbach's relations. Thermally tempered glass shows much higher impact resistance than that estimated from superposition of residual stresses. Subcritical impact sites exhibit slow crack growth in tempered plates, eventually leading to fracture of the entire plate.     

Cryptosporidium Log-inactivation with Ozone Using Effluent CT10, Geometric Mean CT10, Extended Integrated CT10 and Extended CSTR Calculations

The draft Long-Term 2 Enhanced Surface Water Treatment Rule (LT2ESWTR) contains Cryptosporidium log-inactivation CT tables (ozone-in-water concentration [residual], “C” times contact time, T). Depending on water temperature, Cryptosporidium CT values that are listed are 15 to 25 times greater than CT values for equivalent Giardia log-inactivation credit. The elevated operating dose required for Cryptosporidium log-inactivation credit has the potential to increase disinfection by-product (DBP) formation (e.g., bromate). Calculating CT value accurately will minimize ozone dose, which will decrease operating cost and lower DBP formation, and at the same time maintain disinfection protection through implementation of scientifically based safety factors. Various methods are available for calculating CT value. The method chosen depends largely on the available information concerning ozone residual characteristics and hydrodynamic features of the ozone contactor, plus local regulatory requirements. Four methods are discussed in this paper. Each method can be used to calculate Giardia, virus, and Cryptosporidium log-inactivation credit.     

Evaluation of Laminated Circular Elastomeric Bearings

This paper evaluates the behavior and performance of laminated circular elastomeric bearings and compares them to those of square and rectangular bearings. The study included an experimental evaluation and a nationwide survey of state Department of Transportations on the use and performance of circular bearings and bearings in general in their states. The experimental investigation studied the bearings' behavior in compression, compression and rotation, and compression and shear. Results from this limited study showed that the three bearings have similar stress-strain behavior in compression and they are in agreement with the AASHTO LRFD guide stress–strain curves. In compression and rotation, the AASHTO LRFD substructure moments are slightly less than the measured values for circular bearings and rectangular bearings rotated about their strong axis for a compressive stress of 10.3?MPa (1.5?ksi) and slightly higher than those of rectangular bearings rotated about their weak axis. In compression and shear, the shear stiffness of circular and square bearings is in agreement with theoretical values within the range of design displacements. Results from the survey showed that many states are using circular bearings and more states would consider using them, however no maintenance or monitoring data were available on their short-term and long-term performance.     

Evaluation of a proper controller performance for maximum-power point tracking of a stand-alone PV system

In this paper the implementation of a suggested stand-alone PV system, for maximum-power point tracking (MPPT), is carried out. Also, this paper presents a comparative study, through experimental work, between the conventional PI controller and the fuzzy logic controller (FLC) under different atmospheric conditions. The implemented system with both the PI controller and the FLC gives a good maximum-power operation of the PV array, but the tracking capability for different optimum operating points is better and faster for the case of using the FLC compared to the case of using the PI controller.     

A neuron membrane mesh representation for visualization of electrophysiological simulations

We present a process to automatically generate three-dimensional mesh representations of the complex, arborized cell membrane surface of cortical neurons (the principal information processing cells of the brain) from nonuniform morphological measurements. Starting from manually sampled morphological points (3D points and diameters) from neurons in a brain slice preparation, we construct a polygonal mesh representation that realistically represents the continuous membrane surface, closely matching the original experimental data. A mapping between the original morphological points and the newly generated mesh enables simulations of electrophysiolgical activity to be visualized on this new membrane representation. We compare the new mesh representation with the state of the art and present a series of use cases and applications of this technique to visualize simulations of single neurons and networks of multiple neurons.     

Modern Template Design and Biological Evaluation of Cephradine-loaded Magnesium Calcium Silicate Nanocomposites as an Inhibitor for Nosocomial Bacteria in Biomedical Applications

Silicon - Magnesium calcium silicate nanostructures (MCSNS) loaded with (0.0, 0.6, 0.9, and 1.2 wt%) of Cephradine-drug consisting of mesoporous particles were functionally prepared by sol-gel...     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> particles on the microstructure and sliding wear of 7075 Al alloy manufactured by squeeze casting method

Aluminum (Al) alloy 7075 reinforced with Al₂O₃ particles was prepared using the stir casting method. The microstructure of the cast composites showed some degree of porosity and sites of Al₂O₃ particle clustering, especially at high-volume fractions of Al₂O₃ particles. Different squeeze pressures (25 and 50 MPa) were applied to the cast composite during solidification to reduce porosity and particle clusters. Microstructure examinations of the squeeze cast composites showed remarkable grain refining compared with that of the matrix alloy. As the volume fraction of particles and applied squeeze pressure increased, the hardness linearly increased. This increase was related to the modified structure and the decrease in the porosity. The effect of particle volume fraction and squeeze pressure on the dry-sliding wear of the composites was studied. Experiments were performed at 10, 30, and 50 N with a sliding speed of 1 m/s using a pin-on-ring apparatus. Increasing the particle volume fraction and squeeze pressure improved the wear resistance of the composite compared with that of the monolithic alloy, because the Al₂O₃ particles acted as load-bearing constituents. Also, these results can be attributed to the fact that the application of squeeze pressure during solidification led to a reduction in the porosity, and an increase in the solidification rate, leading to a finer structure. Moreover, the application of squeeze pressure improved the interface strength between the matrix and Al₂O₃ particles by elimination of the porosity at the interface, thereby providing better mechanical locking.     

Surgical management of total anomalous pulmonary venous drainage: impact of coexisting cardiac anomalies

BACKGROUND: Recent reports have cited improving results for surgical management of isolated total anomalous pulmonary venous drainage. Complex cases (with other cardiac anomalies) are less frequently reported and are associated with higher mortality. METHODS: Retrospective review identified 170 consecutive patients treated for total anomalous pulmonary venous drainage from 1982 to 1996: 44 cases were "complex" (with significant associated cardiac lesions) and 126 cases were "simple." RESULTS: Operative mortality for simple cases decreased from 26% to 8%, and mortality for complex cases remained constant at 52%. Age, size, and the presence of atrial isomerism were univariate predictors of mortality. Multivariable analysis identified only univentricular hearts and associated cardiac lesions as predictors of operative mortality. Pulmonary artery (n = 16) and arteriopulmonary (n = 7) shunting strategies for complex cases resulted in less than 30% long-term survival. CONCLUSIONS: Despite improvement in survival for simple cases, management of total anomalous pulmonary venous drainage with single-ventricle hearts or other associated cardiac lesions remains problematic.     

Complex structural contribution of the morphotropic phase boundary in Na0.5Bi0.5TiO3 - CaTiO3 system

The correlation between structure and dielectric properties of lead-free (1-x)Na_0.5Bi_0.5TiO₃ - xCaTiO₃ ((1-x)NBT - xCT) polycrystalline ceramics was investigated systematically by X-ray diffraction, combined with impedance spectroscopy for dielectric characterizations. The system shows high miscibility in the entire composition range. A morphotropic phase boundary (MPB), at 0.09?≤?x?<?0.15 was identified where rhombohedral and orthorhombic symmetries coexist at room temperature. The fraction of orthorhombic phase increases gradually with x in the MPB region. Dielectric measurements reveal that the relative permittivity increase with addition of Ca²⁺. This behavior is unusual with this kind of doping. A thermal hysteresis occurred only in the MPB composition which varies in a non-monotonically manner with x, detected by dielectric properties. This phenomenon is related to the crystalline microstructure by a linear relationship between the fraction of each phase and dielectric properties, and, more precisely, to the strong interaction between rhombohedral and orthorhombic phases.     

Multivariate Analysis of the Stability of Spray-Dried Eupenicillium javanicum Peptidases

Peptidases occupy a central position in the enzyme market because of their importance in many areas, such as for physiological processes, foods, and detergents, as well as in the pharmaceutical, leather, and biotechnology industries. Microbial production is among the major sources of peptidases because it presents many advantages when compared with other methods. In this study, the metallopeptidases produced by the fungus Eupenicillium javanicum under a solid-state fermentation bioprocess were spray-dried. The enzymatic extract was dried using drying adjuvants, and optimal conditions for preserving enzymatic activity were studied following a Box-Behnken experimental design. The spray process factors studied were the air-drying temperature, enzyme feed flow rate, and the proportion of enzyme/additive. The responses analyzed were the dry extract yield and enzymatic activity after spray drying. Additionally, the stability of the dry extracts was assessed during 180 days at 4°C and 25°C. The results revealed extract yields of up to 66.12% and good enzymatic activity for intermediate values of temperature and adjuvant proportions. Furthermore, the dried enzymatic extracts showed potential for future commercial applications because of their stability at 25°C for 180 days.