Features of ultrasonic wave propagation to identify defects in composite materials modelled by finite element method

A two-dimensional plane strain finite element model with absorbing boundary condition has been developed to investigate the ultrasonic wave propagation in isotropic and orthotropic media. It is capable of simulating the experimental pulse echo technique to obtain A-scan data, when a short duration pulse is transmitted into a domain with or without a flaw. The flaw can either be a crack or an inclusion of different material such as a Teflon insert or a resin rich zone. After performing FFT on the A-scan data, frequency domain feature analysis is done. The study provides a guideline regarding the suitability of certain harmonics sensitive to certain types of flaw. The simulation shows other important artifacts of wave propagation such as mode conversion and scattering due to the presence of flaws.     

Structural and electrical measurements of CdZnSe composite

TheI—Vcharacterization and the electrical resistivity of selenium rich Se₈₅Cd_15-xZn_x (x = 0, 3, 7, 11 and 15) system at room temperature have been studied. Samples were obtained using melt cooling technique. So prepared samples were then characterized in terms of their crystal structure and lattice parameter using X-ray diffraction method. The materials were found to be poly crystalline in nature, having zinc blend structure over the whole range of zinc concentration. The measurements ofI—V bdcharacteristics have been carried out at different temperatures from room to 140°C. The electrical resistivity of the samples with composition at room temperature has been found to vary between maximum 2.7 x 10⁸ Ωm and minimum 7.3 x 10⁵ Ωm and shows a maximum at 3 at. wt.% of Zn. The carrier activation energy of the samples with composition has also been determined and found to vary from 0.026 eV to 0.111 eV.     

Deceleration of a porous rotating disk in a viscous fluid

The flow due to a rotating disk decelerating with an angular velocity inversely proportional to time with either surface suction (or injection) which again varies with time is investigated. The unsteady Navier-Stokes equations are transformed to non-linear ordinary differential equations using similarity transformations. The resulting equations are solved numerically using a globally convergent homotopy method. The flow depends on two non-dimensional parameters, namely an unsteadiness parameter $\text{S}$ and a suction (or injection) parameter $\text{A}$. Some interesting numerical results are presented graphically and discussed.     

A protocol for distributed simulation on a microcomputer network

The computer industry has evolved very rapidly from single-user computers to computer networks where users are able to share both local and remote files. Networks of microcomputers facilitate the integration of all information processing for distributed applications such as database processing and electronic mail. One management application of promising potential for computer networks is distributed simulation. Simulation analysis can be useful to essentially all problem-solving and decision-making on the job.

To implement a particular distributed application, computer communication between processors must be considered. Unlike expensive multiprocessor computers, networks of less-expensive microcomputers do not have pre-established communication paths between processors. This paper addresses how this obstacle may be overcome by using communication protocols based on the Open Systems Interconnection (OSI) reference model. Protocol services needed to support a distributed simulation environment will be identified, and their implementation through a prototype will then be investigated and evaluated.     

Short‐beam three‐point bend test study in syntactic foam. Part III: Effects of interface modification on strength and fractographic features

Syntactic foam slabs having uncoated microballoons and paraffin oil surface‐treated microballoons were fabricated and tested for short‐beam three‐point bend test. The work points to the role of paraffin oil coating first weakening the interface between the microballoons and the matrix and hence lowering the efficiency of load transfer from matrix to the fillers (i.e., microballoons). This led to an overall decrement of 71% in the experimentally measured strength value compared to the deduced value for uncoated microballoons' specimens. The large strengths for uncoated microballoons specimens can be traced to the presence of the curvilinear marks in the matrix that, incidentally, are absent in the case of paraffin oil coated specimens. These observations are revealed distinctly in the microscopy of test‐failed specimens. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 687–693, 2005     

Short beam three point bend tests in syntactic foams. Part I: Microscopic characterization of the failure zones

Scanning Electron Microscopic (SEM) studies were carried out on the failure surface of syntactic foam material tested in a short beam three point bend test (SBT) by employing 21 × 15 × 3 mm³ dimension bearing specimens. The syntactic foams were fabricated using glass microballoons in epoxy binder. The failure of the tensile, compression, and shear dominated regions were studied by SEM at different magnifications. The tensile region had characteristic features, such as partial debonding of the microballoons from the matrix and cracking of glass microballoons, apart from matrix cracking and some river pattern features. The compression side was characterized by crushing and collapsing of microballoons, resulting in accumulation of debris with no apparent river pattern for matrix‐rich regions. The midway positions of the SBT failed surface comprised of deformation bands in the matrix and occasional debonding of microballoons. The morphology recorded in the tensile and compression regions corroborated well with the results obtained on these foam samples in those specimens that were subjected to pure uniaxial tension and compression, respectively. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 673–679, 2005     

Comparative wear performance of titanium based coatings for automotive applications using exhaust gas recirculation

This paper reports tribological characterization of titanium based coatings ion bonded on steel balls for automotive applications using exhaust gas recirculation (EGR). It is well known that lubricating oil drawn from EGR operated engine is contaminated with soot and higher amounts of wear debris compared to non-EGR operated engine. In this study, steel balls coated with TiN, TiAlN and TiCN are investigated in both fresh lubricating oil and EGR stressed oil for a comparative assessment of their wear characteristics in two mediums. Normal load was applied on the samples, tested against a rotating cast iron disk, simulating ring-liner interaction. In each experiment, about one quarter of disk was dipped in the oil (a) to ensure the presence of a thin oil film on the disk-ball interface during the experiment, and (b) to avoid exposure of the worn surface to atmospheric air. The results reveal that the wear rates of the coatings based on the change in the scar diameters of the samples, tested in EGR oil was 2-4 times higher than that of fresh lubricating oil. It was found that despite lowest hardness, TiN coated samples showed smaller scar diameters than TiAlN and TiCN coated samples in both lubricating oil environments. A simple geometric model was used to calculate the thickness of the coating removed as a function of the test duration. Results show that TiN coatings last for 120 min in fresh oil as compared to 30 min in the EGR oil under normal loading, whereas TiAlN and TiCN coating last for 60 and 30 min respectively in fresh oil and wear out in 15 min in EGR oil.