Barium titanate‐based nanodielectrics of two chemically recyclable thermosets

In this work was investigated the effect of the addition of barium titanate (BaTiO₃) on electrical properties of two chemically recyclable thermosets, polyhemiaminal (PHA) and polyhexahydro‐s‐triazine (PHT), both fabricated from 4,4′‐oxydianiline (ODA), an ether derivative of aniline and paraformaldehyde. Thermal and mechanical properties as well as chemical recyclability of the two polymers and their nanocomposites/nanodielectrics were also investigated. In addition, a quantitative analysis was conducted of the nanoparticle dispersion in the PHA‐/PHT‐based BaTiO₃‐containing nanocomposites using transmission electron microscopy imaging and the nearest‐neighbor distance index and this index was used to analyze the investigated properties in connection with the proper mechanisms. Regarding the electrical properties for both neat polymers, conductivity values of the order of 10^?8 S m^?1 at 100 Hz were observed and dielectric constant values close to 2.80 for both polymers at 1 kHz. The addition of 0.5 wt% of BaTiO₃ ferroelectric nanoparticles increased by about 44% the dielectric constant (1 kHz) and conductivity (10² Hz) of the PHA‐based nanocomposite. PHA and PHT exhibited glass transition temperature (T_g) values in the range 125–180 °C. An increase of 7 °C in T_g was observed after the incorporation of 0.5 wt% of BaTiO₃ into PHA. Concerning the mechanical properties, values in the range 4.00–4.45 GPa for reduced modulus and 0.30–0.43 GPa for nanohardness for PHA and PHT polymers were observed. Independently of filler content or polymer matrix, both mechanical properties were enhanced after the addition of BaTiO₃. The chemical recycling of PHA/PHT and all nanocomposites in the initial ODA reagent after sulfuric acid treatment was successfully characterized using the NMR and Fourier transform infrared spectroscopic techniques. © 2018 Society of Chemical Industry     

Bamboo biochar-catalytic degradation of lignin under microwave heating

Abstract

Lignin biochar-catalytic depolymerization using biochar Fe-600, Fe-800, Ni-600, Ni-800 catalysts under microwave-heating (180?°C for 30?min) was explored in an ethanol/formic acid (1:1) media. Non-catalyst depolymerization was also studied and compared with the biochar-catalysts results. Characteristics of the bio-char catalysts were analyze by BET, XRD, and FT-IR. GPC, FT-IR, and MALDI-TOF MS spectrometry were also used to characterize the depolymerization products. The experimental results showed that the S_BET, V_t, and V_mec and average pore diameter of the biochars are considerably dependent on the preparation temperature and type of cation (Ni²⁺ or Fe³⁺). The maximum yield of bio-oil product was obtained as 85?wt% with the addition of biochar Ni-600 and the total amount of oligomers or monomers with a molecular weight of 164 to 446 reaches 80.4%.     

Fracture response of fibre-reinforced materials with macro/microcrack damage using the Boundary Element Technique

The Boundary Element Method (BEM) incorporating the Embedded Cell Approach (ECA) has been used to analyse the effects of constituent material properties, fibre spatial distribution and microcrack damage on the localised behaviour of transversely fractured, unidirectional fibre-reinforced composites. Three specific composites, i.e., glass fibre reinforced polyester, carbon fibre reinforced epoxy and a glass-carbon hybrid, are considered. The geometrical structures examined were perfectly periodic, uniformly spaced fibre arrangements in square and hexagonal embedded cells. In addition, numerical simulations were also conducted using embedded cells containing randomly distributed fibres. The models involve both elastic fibres and matrix, with the interfaces between the different phases being fully bonded. The results indicate that the constituent material properties (two phase composite) and spatial distribution have a significant effect on the localised stress distributions around the primary crack tip. However, the strain energy release rate associated with crack propagation is predominantly influenced by the material composition. The three-phase hybrid composite exhibited an apparent intermediate fracture toughness value, compared to the all-glass and all-carbon models. Furthermore, the strain energy release rate for the macrocrack lowers as it enters a zone of localised damage (microcracking). The presence of microcracks relaxes the stress field, which can result in a significant reduction in the energetics of the primary crack.     

1H T2‐NMR monitoring of crosslinked polyolefin aging

This work examines the correlation between the ¹H‐NMR T₂ relaxation constant and the mechanical properties of aged crosslinked polyolefin cable insulation. T₂ experiments on unswollen samples could not differentiate between unaged and highly aged materials; all exhibited ¹H T₂ constants of approximately 0.5 ms. To accentuate the effects of aging, samples were swollen in various solvents. Unaged samples had T₂ values of approximately 15 ms in good solvents. With thermal aging, T₂ values decreased as the ultimate tensile elongation decreased. However, the correlation between T₂ and elongation differed for samples irradiated with high‐energy radiation and for materials aged above versus below the crystalline melting temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2578–2582, 2003     

Area- and time-specific marginal capacity costs of electricity distribution

Marginal costs of electricity vary by time and location. In the past, researchers attributed the variations to factors related to electricity generation and transmission. These authors, however, have not analyzed possible variations in marginal distribution capacity costs (MDCC). The objectives of this paper are:

1. (i) to show that large MDCC variations are due to the dispersion in distribution capital expenditures by time and space,

2. (ii) to propose a method for quantifying the area- and time-specific MDCC in the presence of lumpy investments, and

3. (iii) to compare our MDCC estimates to those commonly used in the electric utility industry.

Our proposed method and its results were adopted by the California Public Utilities Commission (CPUC) in 1992 for Pacific Gas and Electric Company (PG&E), the largest privately owned electric utility in the U.S.     

Optimal design of gating systems by gradient search methods

A numerical optimization technique based on gradient-search is applied to obtain an optimal design of a typical gating system used for the gravity process to produce aluminum parts. This represents a novel application of coupling nonlinear optimization techniques with a foundry process simulator, and it is motivated by the fact that a scientifically guided search for better designs based on techniques that take into account the mathematical structure of the problem is preferred to commonly found trial-and-error approaches. The simulator applies the finite volume method and the VOF algorithm for CFD analysis. The direct gradient optimization algorithm, sequential quadratic programming (SQP), was used to solve both a 2D and a 3D gating system design problems using two design variables. The results clearly show the effectiveness of the proposed approach for finding high quality castings when compared with current industry practices.