Polyetherimide-LaNi5 composite films for hydrogen storage applications

This study investigates the preparation of polyetherimide (PEI) – LaNi₅ composites films for hydrogen storage. Prior to the polymer addition, LaNi₅ was ball-milled at different conditions (250, 350, and 450 RPM) and annealed at 500 °C for 1 h under vacuum. The composites were produced with BM-LaNi₅-350 (PEI/LaNi₅-350) and annealed BM-LaNi₅-350 (PEI/LaNi₅-350-TT). Membranes were successfully produced through solvent casting assisted by an ultrasonic bath. The particles dispersion and the film morphology did not change after hydrogenation cycles. In the H₂ sorption experiments at 43 °C and 20 bar, the films stored H₂ without incubation time; both samples reached a capacity of ~0.6 wt%. The H₂ sorption kinetics of PEI/LaNi₅-350 was comparable to that of BM-LaNi₅-350, whereas PEI/LaNi₅-350-TT presented significantly slower kinetics. LaNi₅ oxidation was hindered by PEI, showing that it can be explored to improve metal hydrides air resistance. The results demonstrated that PEI films filled with LaNi₅ are promising materials for hydrogen storage.     

Real‐time monitoring by proton relaxometry of radical polymerization reactions of acrylamide in aqueous solution

The potential of time‐domain nuclear magnetic resonance (TD‐NMR) for the real‐time monitoring of solution radical polymerizations is demonstrated. A model system composed of a redox‐pair initiator system, acrylamide as monomer and water as solvent was investigated. A second‐generation continuous wave free precession technique was employed to measure the longitudinal relaxation time constant (T₁) of the samples throughout the polymerization reactions. This parameter was shown to be sensitive to the reactant feed free‐radical enhancement of the water molecule relaxation time, making it a good probe to monitor monomer conversion in real time in an automated, non‐destructive fashion. It was found that the T₁ value was better than the transverse relaxation time constant (T₂) for describing the evolution of the polymerization reactions, due to its greater sensitivity to paramagnetic effects. The TD‐NMR signal variation observed was linked to the formation, propagation and termination steps of the radical polymerization kinetics scheme. These first results may contribute to the application of real‐time monitoring of radical polymerization reactions employing low‐cost and robust TD‐NMR spectrometers. © 2018 Society of Chemical Industry     

Accurate estimation of capacities and cross-traffic of all links in a path using ICMP timestamps

The estimation of the link capacity and its available bandwidth in an end-to-end path is crucial for network management, admission control and flow control for adaptive applications. This paper introduces an estimation mechanism able to accurately estimate the available bandwidth of all links in an end-to-end path, through its capacity and cross-traffic estimation. The estimation procedures resort to the dispersions of packet pairs and trains using the concepts of ICMP Timestamp and Traceroute that, efficiently used together, enable the measurement of the dispersions in all links in the path. These mechanisms were evaluated through simulation experiments, where we analyzed the influence of the several network parameters on each estimation mechanism. The results show that these estimation methods are able to accurately estimate both the capacity and the cross-traffic of all links in a path with moderate length and with low overhead.     

Preparation and characterization of chitosan‐based dispersions

Complexation of chitosan in aqueous solutions by low molecular weight electrolytes is one of the simplest methods for the preparation of aqueous chitosan dispersions. In this work, the influence of storage time, sulfate concentration, method of preparation and surfactant content on some properties of the resultant chitosan dispersions (turbidity, viscosity and zeta potential) was analyzed. Turbidimetry was adequate to monitor the formation of particles, while viscometry was suitable to monitor changes in the dispersing phase. An analysis of the properties of these systems, mainly in terms of particle–particle and macromolecule–macromolecule interactions was carried out. Copyright © 2004 Society of Chemical Industry     

Atmospheric corrosion of reference metals in Antarctic sites

This paper presents the results obtained at three Antarctic test sites participating in the “Ibero-American Map of Atmospheric Corrosiveness” (MICAT), a project on atmospheric corrosion carried out during the period 1988–1994 at some 70 sites distributed across 12 countries of the Latin-American region, Spain and Portugal. The three Antarctic sites are located near the coastline.The singular climatic characteristics of Antarctic regions are related with the purity of the air, the absence of rainfall and the formation of ice on the metallic surface during an important part of the exposure time. However, electrochemical activity is possible below ice layers. This situation affects the structure and morphology of corrosion product films and the resulting corrosion rates of metallic surfaces.     

Mechanical improvement of concrete by irradiated polypropylene fibers

Fiber reinforced concrete (FRC) contains fibers physically mixed with gravel, sand, cement, and water. So far, adequate mechanical performance of FRC has been obtained at high cost and using complex technologies; important here is the geometry and surface characteristics of the polymers. We have modified polymeric‐fiber surfaces by using gamma radiation. Irradiated polypropylene (PP) fibers were submitted to 0, 5, 10, 50, and 100 kGy of gamma irradiation dosages. First, tensile strength of PP fibers was evaluated, and then fibers blended at 0, 1.0, 1.5, and 2.0% in volume with Portland cement, gravel, sand, and water. The highest values of compressive strength were obtained with irradiated‐fibers at 10 kGy and 1.5% in volume of fiber. The result is 101 MPa, as compared to 35 MPa for simple concrete without fibers. POLYM. ENG. SCI., 45:1426–1431, 2005. © 2005 Society of Plastics Engineers     

Full Complex Amplitude Digital Holograms： Design, Fabrication and Optical Characterization

Diffractive optical elements have a large number of industrial applications, such as beam shaping and optical filtering. Traditionally, these elements modulate the phase of the incoming light or its amplitude, but not both. To overcome this limitation, full complex-amplitude modulation diffractive optical elements were developed. Well-established integrated circuit fabrication steps were employed to fabricate the devices with high precision. Using this approach, the new element‘s optical performances are improved also for near field operations. With this device it is possible to obtain 100% efficient spatial filtering and low noise reconstructed images.