High temperature transport kinetics in heteroepitaxial LaFeO3 thin films

Heteroepitaxial LaFeO₃(1 1 0) thin films with a thickness of 150 nm were grown on LaAlO₃(0 0 1) by reactive sputtering in an inverted cylindrical magnetron geometry. Equilibrium conductivity was measured as a function of partial pressure of oxygen at T=1000 °C, and logσ plotted vs. logP(O₂) showed a minimum in conductivity for P(O₂)=10⁻¹¹ atm and a linear response between 10⁻¹⁰ and 1 atm. This linear response makes thin films of LaFeO₃ a promising material for oxygen sensor applications. We have also measured the time response of the film conductivity upon an abrupt change in the partial pressure of ambient oxygen from 10⁻² to 10⁻³ atm, which was determined at 60 s for T=700 °C and <3.5 s at T=1000 °C.     

Infants of diabetic mothers (IDM). II -- Fibronectin and perinatal morbidity

OBJECTIVE: The objective of this study was to determine fibronectin levels in umbilical cord blood of infants of diabetic mothers (IDM) and evaluate a possible correlation with perinatal pathology. PATIENTS AND METHODS: A prospective study of 58 IDM (33 males and 25 females) and 58 control newborns (NB) (33 males and 25 females) was carried out. RESULTS: There were no differences in fibronectin levels between the two groups nor between the sexes. Perinatal morbidity was higher in the IDM group, but there was no correlation between fibronectin levels and the presence of perinatal pathology. CONCLUSIONS: Fibronectin levels are not useful in the perinatal evaluation of infants of diabetic mothers.     

High-Temperature Creep Behavior of Mixed Conducting La0.5Sr0.5Fe1−xCoxO3-δ (0.5≤x≤1) Materials

Steady-state compressive creep rate of La_0.5Sr_0.5Fe_0.5Co_0.5O_3−δ (LSFC) and La_0.5Sr_0.5CoO_3−δ (LSC) is reported in the temperature region 900°–1050°C and stress range 5–28 MPa. The stress exponents for the two materials were 1.71±0.18 and 1.24±0.15, respectively. The activation energy for creep was considerably higher for LSC (619±56 kJ/mol) than for LSFC (392±28 kJ/mol). The grain size exponent for LSC was 1.28±0.14. Considerably higher creep rates were observed for both materials in N₂ compared with air. Relaxation by creep of chemical-induced stresses in oxygen-permeable membranes is addressed, especially at low partial pressure of oxygen.     

Sintering behaviour of La1−xSrxFeO3−δ mixed conductors

The sintering properties of La_1−xSr_xFeO_3−δ (x = 0.1, 0.25) mixed conductors have been investigated with particular emphasis on the effect of secondary phases due to cation non-stoichiometry (±5 mol% La excess and deficiency). Secondary phases, located at grain boundaries in cation non-stoichiometric materials, increased the sintering temperature compared to single-phase materials. Extensive swelling in final stage of sintering was observed in all materials, which resulted in micro-porous materials. The swelling was most pronounced in the phase pure and two-phase materials due to La-deficiency, while refractory secondary phases in La-excess materials inhibited both sintering, grain growth and swelling. In La-deficient materials, formation of molten secondary phases resulted in rapid swelling due to viscous flow. The present findings demonstrated the importance of controlling sintering temperature and time, as well as careful control of the cation stoichiometry of La_1−xSr_xFeO_3−δ in order to achieve fully dense and homogenous La_1−xSr_xFeO_3−δ ceramics.     

The stability of refractory oxides in sodium-rich environments

The infiltration of molten electrolyte and sodium is known to deteriorate the refractory in aluminum electrolysis. The mineralogical changes due to reactions with molten fluorides have previously been described throughly, while the effect of sodium has not been considered in detail. This paper presents an experimental study of the chemical stability of some refractory materials in sodium-rich environments. The materials were exposed to sodium vapor at 800°C for 4 hours. The mineralogical transformations and deterioration of the materials due to reactions with sodium were analyzed by x-ray diffraction and optical and electron microscopy.     

Non-standard bone simulation: interactive numerical analysis by computational steering

Numerous numerical methods have been developed in an effort to accurately predict stresses in bones. The largest group are variants of the h-version of the finite element method (h-FEM), where low order Ansatz functions are used. By contrast, we3 investigate a combination of high order FEM and a fictitious domain approach, the finite cell method (FCM). While the FCM has been verified and validated in previous publications, this article proposes methods on how the FCM can be made computationally efficient to the extent that it can be used for patient specific, interactive bone simulations. This approach is called computational steering and allows to change input parameters like the position of an implant, material or loads and leads to an almost instantaneous change in the output (stress lines, deformations). This direct feedback gives the user an immediate impression of the impact of his actions to an extent which, otherwise, is hard to obtain by the use of classical non interactive computations. Specifically, we investigate an application to pre-surgical planning of a total hip replacement where it is desirable to select an optimal implant for a specific patient. Herein, optimal is meant in the sense that the expected post-operative stress distribution in the bone closely resembles that before the operation.     

Covering a line segment with variable radius discs

The paper addresses the problem of locating sensors with a circular field of view so that a given line segment is under full surveillance, which is termed as the disc covering problem on a line. The cost of each sensor includes a fixed component f, and a variable component that is a convex function of the diameter of the field-of-view area. When only one type of sensor or, in general, one type of disc, is available, then a simple polynomial algorithm solves the problem. When there are different types of sensors, the problem becomes hard. A branch-and-bound algorithm as well as an efficient heuristic are developed for the special case in which the variable cost component of each sensor is proportional to the square of the measure of the field-of-view area. The heuristic very often obtains the optimal solution as shown in extensive computational testing.     

Capturing Global Youth: Mobile Gaming in the U.S., Spain,and the Czech Republic

We adapt the technology acceptance model (TAM) to examine the factors influencing mobile gaming adoption among “global youth.” Our model replaces usefulness with convenience, incorporating visual appeal and escapism as antecedents of fun, and perceived novelty and economic value as antecedents of convenience. Questionnaire surveys were conducted in the U.S., Spain, and the Czech Republic, producing 432 usable responses. In the structural model assessment with the pooled sample, convenience exercises greater effects on attitude toward mobile games than fun, suggesting that the most important driver is probably the capability of being used flexibly at any time and in any place, rather than mere enjoyment. Tests of latent means suggest that most dimensions are perceived more strongly in the Czech Republic.