A STUDY OF THE FLOTATION OF OXIDIZED AHASRA COAL

The flotation of oxidized Amasra Coal which was collected between 1973-1978 and, stored in the atmospheric conditions was examined In this work. Coal samples were fractioned by wet screening to +0.560 mm, -0.500 + 0.140 mm, -0.140 mm particle sizes and first fraction was ground to -0.560 mm before flotation. Motorin and pine oil which had been heated at 125° C for 5 hours were used ns flotation reagents. The influence of impeller speed, aeration rate, solid concent of the pulp, reagent amounts were examined and optimum values were determined. Increase of the pine oil amount added to the pulp, increased the coal. recovery on the flotation of this oxidized coal.     

Window materials for high power gyrotron

The room temperature application of sapphire as window material at higher frequencies is not feasible since its absorption coefficient increases almost linearly with increasing frequency in the millimeter wavelength region. At cryogenic temperature the absorption coefficient value decreases only by a few factors (factor of 2 to 3) in the 90 – 200 GHz region. The earlier reported temperature squared dependence (decrease) in the absorption coefficient or the loss tangent value is totally absent in our broad band continuous wave data we are reporting here (at 6.5 K, 35K, 77K and 300K) and one we reported at conferences earlier. Our results are verified by another technique. We utilize our precision millimeter wave dispersive Fourier transform spectroscopic techniques at room temperature and at cryogenic temperatures The extra high resistivity single crystal compensated silicon is no doubt the lowest loss material available at room temperature in the entire millimeter wavelength region At higher millimeter wave frequencies an extra high resistivity silicon window or an window made with extra high resistivity silicon coated with diamond film would certainly make a better candidate in the future. A single free standing synthetic diamond window seems to have higher absorption coefficient values at millimeter wavelength region at this time although it is claimed that it possesses good mechanical strength and higher thermal conductivity characteristics. It certainly does not rule out the use of diamond film on a single crystal high resistivity silicon to improve its mechanical strength and thermal conductivity     

Royal Crown Shaped Polarization Insensitive Perfect Metamaterial Absorber for C-, X-, and Ku-Band Applications

This study proposed a new royal crown-shaped polarisation insensitive double negative triple band microwave range electromagnetic metamaterial absorber (MA). The primary purpose of this study is to utilise the exotic characteristics of this perfect metamaterial absorber (PMA) for microwave wireless communications. The fundamental unit cell of the proposed MA consists of two pentagonal-shaped resonators and two inverse C-shaped metallic components surrounded by a split ring resonator (SRR). The bottom thin copper deposit and upper metallic resonator surface are disjoined by an FR-4 dielectric substrate with 1.6 mm thickness. The CST MW studio, a high-frequency electromagnetic simulator has been deployed for numerical simulation of the unit cell in the frequency range of 4 to 14 GHz. In the TE mode, the offered MA structure demonstrated three different absorption peaks at 6.85 GHz (C-band), 8.87 GHz (X-band), and 12.03 GHz (Ku-band), with 96.82%, 99.24%, and 99.43% absorptivity, respectively. The electric field, magnetic field, and surface current distribution were analysed using Maxwell’s-Curl equations, whereas the angle sensitivity was investigated to comprehend the absorption mechanism of the proposed absorber. The numerical results were verified using the Ansys HFSS (high-frequency structure simulator) and ADS (advanced design system) for equivalent circuit models. Moreover, the proposed MA is polarisation and incident angle independent. Hence, the application of this MA can be extended to a great extent, including airborne radar applications, defence, and stealth-coating technology.     

Sodium and ultrafiltration profiling in hemodialysis: A long-forgotten issue revisited

Sodium and ultrafiltration profiling are method of dialysis in which dialysate sodium concentration and ultrafiltration rate are altered during the course of the dialysis session. Sodium and ultrafiltration profiling have been used, commonly simultaneously, to improve hemodynamic stability during hemodialysis. Sodium profiling is particularly effective in decreasing the incidence of intradialytic hypotension, while ultrafiltration profiling is suggested to decrease subclinical repeated end organ ischemia during dialysis. However, complications such as increased interdialytic weight gain and thirst due to sodium excess have prevented widespread use of sodium profiling. Evidence suggest that different sodium profiling techniques may lead to different clinical results, and preferring sodium balance neutral sodium profiling may mitigate adverse effects related to sodium overload. However, evidence is lacking on the long-term clinical outcomes of different sodium profiling methods. Optimal method of sodium profiling as well as the utility of sodium/ultrafiltration profiling in routine practice await further clinical investigation.     

Inventory lot-sizing with supplier selection using hybrid intelligent algorithm

In supply chain management (SCM), multi-product and multi-period models are usually used to select the suppliers. In the real world of SCM, however, there are normally several echelons which need to be integrated into inventory management. This paper presents a hybrid intelligent algorithm, based on the push SCM, which uses a fuzzy neural network and a genetic algorithm to forecast the rate of demand, determine the material planning and select the optimal supplier. We test the proposed algorithm in a case study conducted in Iran.     

Stress intensity factors of two diametrically opposed edge cracks in a thick-walled functionally graded material cylinder

A method is developed to evaluate stress intensity factors for two diametrically-opposed edge cracks emanating from the inner surface of a thick-walled functionally graded material (FGM) cylinder. The crack and the cylinder inner surfaces are subjected to an internal pressure. The thermal eigenstrain induced in the cylinder material due to nonuniform coefficient of thermal expansion after cooling from the sintering temperature is taken into account. First, the FGM cylinder is homogenized by simulating its nonhomogeneous material properties by an equivalent eigenstrain, whereby the problem is reduced to the solution of a cracked homogenized cylinder with an induced thermal and an equivalent eigenstrains and under an internal pressure. Then, representing the cracks by a continuous distribution of edge dislocations and using their complex potential functions, generalized formulations are developed to calculate stress intensity factors for the cracks in the homogenized cylinder. The stress intensity factors calculated for the cracks in homogenized cylinder represents the stress intensity factors for the same cracks in the FGM cylinder. The application of the formulations are demonstrated for a thick-walled TiC/Al₂O₃ FGM cylinder and some numerical results of stress intensity factors are presented for different profiles of material distribution in the FGM cylinder.     

Modulation of the expression on constitutive rat hepatic cytochrome P450 isozymes by 5-fluorouracil

BACKGROUND and OBJECTIVE: The purpose of this study was to compare morphologic changes following C02 laser or manual curette treatment of calculus-ladened tooth root surfaces. STUDY DESIGN/MATERIALS and METHODS: Laser treatment consisted of repeated single passes with a 6 Watt focused beam at 20 pulses per second, a pulse length of 0.01 second, and a manufacturer's laser efficiency rating of 86% (i.e., the amount of total power delivered through the aperture). The rate of beam passage over the target surface was controlled at 4 mm/second using an 0.8 mm diameter tip. The calculated energy density was 240 J/cm2 for each pass of the beam. Scaled and root planed surfaces were treated with a standardized force of 600 grams using new curettes. Specimens were evaluated by scanning electron microscopy. RESULTS: Laser-induced surface changes included charring, meltdown and resolidification of calculus mineral, and ablation of microbial plaque. Laser-treated specimens also exhibited residual calculus and microbial plaque deposits in areas directly adjacent to the beam path. Scaled and root planed surfaces featured smooth and/or scale like smear layers and islands of residual calculus and microbial plaque. CONCLUSIONS: The rough surface topography resulting from laser treatment and residual calculus and microbial plaque deposits indicates that C02 laser treatment of exposed root surfaces is, at best, an adjunct to traditional methods of therapy.     

Analysis and measurement of a broadband spiral antenna

A broadband spiral antenna (2 to 18 GHz) is modeled using the FDTD method. The inner turn of the antenna is an Archimedean spiral, while the outer turn is an Archimedean spiral with a zigzag shape. The current-density distribution along the spiral arms is first presented in the time domain, interestingly manifesting the impulse current propagation from the feed point to the outer end of the spiral arms. The performance of the broadband spiral antenna is also measured in an anechoic chamber. The simulated and measured results showed the sensitivity of the axial ratio and radiation pattern to the current distribution. The simulated linear gain, radiation patterns, and axial ratios agree well with the measured data over all of the frequency range from 2 to 18 GHz.     

Submillimeter wave photoconductivity observation of shallow donors in In0.53Ga0.47As

The hydrogen like 1s → 2p (m=?1,0,+1) transitions of two donors have been observed in high intensity magnetic fields up to 8.5T. The m=?1 transitions ocurred between 2 cm^?1 and 25 cm^?1. The signature curves for donors in ternary semiconductor In_0.53Ga_0.47As have now been established.     

Ultimate method for unambiguous identification of all donors in epitaxial GaAs and related compounds

When epitaxial GaAs is grown by the method of molecular beam epitaxy (mbe) it would be p-type unless it is intentionally doped lightly during growth by using a particular substitutional donor atom. We have chosen the tin donor in this case to render the specimen n-type. Then the conventional far infrared photoconductivity technique is used to observe the 1s to 2p transition of the electron of the tin donor. The identity of the donor, the energy of the quantum transition as a function of applied magnetic field intensity, and the line shape characteristics of that particular donor then become unquestionable.