Fabrication of co-PVDF/modacrylic/SiO2 nanofibrous membrane: Composite separator for safe and high performance lithium-ion batteries

Highly porous free-standing co-poly(vinylidene fluoride)/modacrylic/SiO₂ nanofibrous membrane was developed using electrically-assisted solution blow spinning method. The performance and the potential of the membrane as a lithium-ion battery separator were investigated. The addition of modacrylic enhanced the solution spinnability that resulted in defect-free membranes. Moreover, the presence of modacrylic enhanced the dimensional and thermal stabilities, while the addition of hydrophilic SiO₂ nanoparticle enhanced both mechanical property and ionic conductivity. Combustion test results illustrated that the presence of modacrylic provide flame retarding property over a set of different polymeric-based membranes. Electrochemical performance results showed that the developed membrane can increase the battery capacity compared with the commercial separator.     

All Solution‐Based Fabrication of Copper Oxide Thin Film/Cobalt‐Doped Zinc Oxide Nanowire Heterojunctions

Versatile and intriguing solution‐based processes are utilized to synthesize nanostructured materials for device applications to reduce material production and device fabrication costs. This study presents results on the fabrication and characterization of copper oxide (CuO) coated cobalt‐doped zinc oxide nanowires (Co‐doped ZnO NWs)‐based heterojunction diodes prepared by a two‐step synthesis route through combined hydrothermal growth and sol–gel spin coating. Highly dense, well‐ordered, undoped, and Co‐doped ZnO NWs were successfully grown by hydrothermal method. Complementary CuO thin films were synthesized by sol–gel method and subsequently coated onto both undoped and Co‐doped ZnO NWs through spin‐coating technique. Enhanced diode properties with a rectification ratio of 10³ at ±2 V and an ideality factor of n = 2.4 (in dark) were obtained for Co‐doped ZnO NWs‐based heterojunction diodes. The obtained results demonstrated that the investigated heterojunction diode structure fabricated by facile and cost‐effective solution‐based processes can be a promising candidate for the next generation optoelectronic devices.     

Analysis of probability and energy of nanometre CMOS circuits in presence of noise

Motivated by the necessity to consider probabilistic approaches to future designs, probability and switching energy characteristics of probabilistic CMOS (PCMOS) circuits are analysed. Using 90 and 65 nm processes, detailed analytical models for the probability of correctness (p) of these circuits are developed and verified through circuit simulations.     

Structural Design of Lunar Radio Telescope Using Interactive CAD

Some astronomers are considering the moon as an attractive location within the inner solar system for a variety of astronomical observatories, some of which could be operational early in the 21st century. This paper describes the computer‐aided structural design of a 122‐m diameter, fully steerable, parabolic radio telescope to be located on the moon. The loads acting on such a reflector differ substantially from those acting on a reflector that must operate in earth's environment. The moon has excellent advantages as a location for such an instrument. The absence of atmosphere completely eliminates the wind, snow, and ice loads. The gravity field is only one‐sixth that of earth's. The thermal changes from night to day are severe, but structural problems can be avoided by using a thermally stable composite material. Structural elements for the reflector dish have been analyzed and designed for static loads with a specially written interactive graphical computer program. The resulting structure has a mass nearly 40 times less than its earth's counterpart made of steel. The evaluation of the results of the design studies supports the possibility of building a large‐aperture parabolic radio telescope on the moon.     

Influence of thermal annealing on microstructural,morphological, optical properties and surface electronic structure of copper oxide thin films

In this study, effect of the post-deposition thermal annealing on copper oxide thin films has been systemically investigated. The copper oxide thin films were chemically deposited on glass substrates by spin-coating. Samples were annealed in air at atmospheric pressure and at different temperatures ranging from 200 to 600°C. The microstructural, morphological, optical properties and surface electronic structure of the thin films have been studied by diagnostic techniques such as X-ray diffraction (XRD), Raman spectroscopy, ultraviolet–visible (UV–VIS) absorption spectroscopy, field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The thickness of the films was about 520 nm. Crystallinity and grain size was found to improve with annealing temperature. The optical bandgap of the samples was found to be in between 1.93 and 2.08 eV. Cupric oxide (CuO), cuprous oxide (Cu₂O) and copper hydroxide (Cu(OH)₂) phases were observed on the surface of as-deposited and 600 °C annealed thin films and relative concentrations of these three phases were found to depend on annealing temperature. A complete characterization reported herein allowed us to better understand the surface properties of copper oxide thin films which could then be used as active layers in optoelectronic devices such as solar cells and photodetectors.     

A new spatial path persistency model for TOA-based indoor geolocation

Analysis of the persistency and birth/death of multipath components of the channel impulse response is essential for performance evaluation of indoor geolocation algorithms using indirect paths for ranging. The use of indirect paths via multipath diversity is particularly important for situations where the direct path gets blocked. In this letter, we propose a statistical model for the spatial behavior of the persistency of multipath components as a mobile moves inside a building. Based on empirical data from a measurement calibrated ray tracing algorithm we show that the persistency in a typical building is modeled by log-logistic distribution rather than commonly assumed exponential distribution and path birth can be modeled as a Poisson distribution.     

Optimization of centrifugally spun thermoplastic polyurethane nanofibers for air filtration applications

While our knowledge of fiber formation by using conventional nanofiber spinning techniques has increased to a considerable extent, there are still few studies on centrifugal spinning either in academia or in the industry. Centrifugal spinning is a comparatively new method of producing fibers having nano- or microscale diameters. In this study, three main parameters (nozzle orifice diameter, rotational speed, polymer concentration) of centrifugal spinning were optimized to produce air filter media from thermoplastic polyurethane nanofibers. The effect of concentration of polymer solution was found to be a major contributor in TPU fibers optimization estimating 77.5%. After the optimization studies, the average fiber diameter of nanofiber sample produced at optimum conditions (22G needle as an orifice, 4000 rpm, and 10 wt% concentration of polymer solution) was 205 ± 84 nm. Aerosol filtration performance of the produced webs was analyzed. Filtration efficiency of the optimized sample was found to be 99.4% for 0.3 µm particle size at an expense of 98 Pa pressure drop.

Copyright © 2018 American Association for Aerosol Research     

Comparison of the translucency of two multishaded composite resins polymerized with direct or indirect method

The aim of this study was to measure the translucency of one indirect and direct resin composite after polymerization and to examine the effect of color parameters on this property. Tescera and Filtek Ultimate, each containing three shade groups (Enamel, Dentin and Body for Filtek Ultimate; and Incisal, Opaceous Dentin and Body for Tescera), were investigated. The translucency parameter (TP) was measured as the color difference between a specimen over a white and black background. Significant differences were observed in TP values between shade groups. Tukey’s multiple comparison test revealed TP values among the groups of Filtek Ultimate-Enamel > Tescera-Incisal > Filtek Ultimate-Body > Tescera-Body = Filtek Ultimate-Dentin > Tescera-Opaceous Dentin. In conclusion, it is concluded that the translucency of resin composite was affected by polymerization and color parameters.     

Cost analysis of seawater desalination with reverse osmosis in Turkey

Economically usable water resources per capita are decreasing due to excessive population increase each year in Turkey. For this reason, new water resources should be found in the near future. The potential water resources are seawater or well water both of which need removal of salinity. The most promising treatment method for salinity is reverse osmosis. While reverse osmosis becomes widespread, the cost of the process will decrease. There is no detailed information about cost of seawater desalination in Turkey. In this study, a cost analysis of seawater desalination in Turkey was performed for reverse osmosis systems. The basic parameters of cost analysis such as capacity, recovery, membrane life, energy, chemical costs and flux were evaluated based on the effects on capital, operating and total production costs.     

The Small and Silent Force Multiplier: A Swarm UAV—Electronic Attack

At the last two decades, according to UAVs concepts and technological advances, there have been lots of unimagined improvements. Nowadays there are serious works and researches about the usage of UAVs in military operations at electronic warfare (EW) missions. But most of the work on UAV platforms is based upon the advantages of a single, big, expensive, and non-expendable platform. In this study, to get rid off the disadvantages of a stand alone platform a new concept is developed consisting of multiple UAVs with smaller dimensions, at a cheaper price and a wider coverage. According to clarify the study, firstly the EW and RADAR systems and then the swarm UAV concepts are explained. In this manner the current and previous works are pointed out and then the use of the swarm UAVs for EA in military operations is stated. Objectively, the swarm UAV concept’s advantages and some outstanding challenges to the intra-theater space have been put forward regarding the information mentioned above. As a result it is considered that the swarm UAV systems will be tasked important EW missions in the future operation theatres, as soon as the technical handicaps are solved.