We report a novel pH-sensitive hydrogel based micro-valve for metered flow that has applications in a laboratory made “Intelligent valving system”. The hydrogel solution was prepared through Chitosan and poly vinyl alcohol in acetic acid and crystallized using gluteraldehyde as the crosslinking agent in the form of thin wafers and it was found to be very sensitive to pH changes. The pore structure of hydrogel was investigated through Field Emission Scanning Electron Microscopy and thin wafers of the gel were physically placed inside PDMS microchannels. Flow metering in these channels was observed by controlled expansion of the hydrogel plug till complete valving was realized. This valving device was further precisely characterized with micro Particle Image Velocimetry using a solution containing fluorescent polymeric micro beads. The principle advantage of this hydrogel device is the smaller range of pH (varying between pH 3 and 7) over which the valving response is observed. 相似文献
The mathematical formulation for targeting during energy allocation with carbon capture and storage (CCS) is formally developed. For operating-cost optimization with zero excess, it is shown that CCS sources may be regarded as resources with their cost taken as the increment over the non-CCS option. CCS sources along with clean-carbon resources may then be targeted by profile matching with the limiting composite to establish optimal primary cases. The limiting composite curve is itself sacrosanct and obtained by a single computation of the composite table algorithm (CTA) including only non-CCS sources. Carbon emission networks (CENs) are designed by the nearest neighbors algorithm (NNA). A cost criterion is established to determine cost-factor ranges for optimality of the primary cases, and results validated by solving linear programming (LP) and mixed integer linear programming (MILP) formulations. The methodology essentially comprises four distinct stages – targeting, network design, cost analysis, and optimization – with the first two stages not requiring any cost data. 相似文献
Atomically thin transition metal dichalcogenides (TMDs) have distinct opto-electronic properties including enhanced luminescence and high on-off current ratios, which can be further modulated by making more complex TMD heterostructures. However, resolution limits of conventional optical methods do not allow for direct nanoscale optical-structural correlation measurements in these materials, particularly of buried interfaces in TMD heterostructures. Here we use, for the first time, electron beam induced cathodoluminescence in a scanning transmission electron microscope (CL-STEM) to measure optical properties of monolayer TMDs (WS2, MoS2 and WSSe alloy) encapsulated between layers of hBN. We observe dark areas resulting from localized (~ 100 nm) imperfect interfaces and monolayer folding, which shows that the intimate contact between layers in this application-relevant heterostructure is required for proper inter layer coupling. We also realize a suitable imaging method that minimizes electron-beam induced changes and provides measurement of intrinsic properties. To overcome the limitation of small electron interaction volume in TMD monolayer (and hence low photon yield), we find that encapsulation of TMD monolayers with hBN and subsequent annealing is important. CL-STEM offers to be a powerful method to directly measure structure-optical correspondence in lateral or vertical heterostructures and alloys.
Gravure is a high throughput printing process, normally associated with speed, quality, and long print runs. It is widely used for printing on shrink films and other substrates. The shrink films, in particular, polyvinyl chloride (PVC) and glycol-modified polyethylene terephthalate (PET-G), are two dominant substrates widely consumed and printed by gravure process. The PVC and PET-G offer different properties which greatly influence the printability. The surface energy of the substrate determines the adhesion and wettability of ink, while electrical properties such as surface and volume resistivity impact electrostatic assist (ESA) performance. The introduction of ESA in gravure further improved the print quality by eliminating dot skips with reduced impression pressure. However, print defects such as print mottle is inevitable. Print mottle occurs due to a discrepancy between substrate, ink, and process parameters which degrade the print quality. These complexities need to be addressed to deliver higher productivity with less print waste. Therefore, the study investigates the effect of process parameters, i.e., substrate type, line screen, air gap (distance between charge bar and impression roller), viscosity, voltage, and speed, and aims to quantify their effect numerically on defect minimization. The Design of Experiments (DOE) was generated for the above-mentioned parameters and analyzed to extract the best combination of process parameters. The optimized setting showed a reduction in solid mottle by 54% and 57% for PET-G and PVC, respectively. 相似文献
Journal of Mechanical Science and Technology - A dielectric fluid plays a significant role on the machining efficiency of Electric discharge machining (EDM). Two phase (liquid-air) dielectric... 相似文献
BaTi1−xFexO3 compositions (for x = 0, 0.1, and 0.2) were prepared via a solid-state reaction route. The presence of iron (Fe) in barium titanate (BaTiO3) eventually decreased the energy bandgap; thus, its utilization for water cleaning application through photocatalysis process was explored (using methylene blue [MB] dye as an indicative pollutant in water). Characterization of the synthesized powder was performed through scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy. The bandgap of the synthesized powder was calculated as 3.2, 2.12, and 1.67 eV for BaTi1−xFexO3 compositions (for x = 0, 0.1, and 0.2), respectively. BaTi0.8Fe0.2O3 powder showed excellent results, and ∼71% of the MB dye (∼5 mg/L concentrated) was degraded using the photocatalysis process under visible light. To check the potentiality of BaTi1−xFexO3 compositions (for x = 0, 0.1, and 0.2), the photocatalysis process was carried out by changing the concentration of MB dye (2.5–10 mg/L with a step of 2.5 mg/L) and the amount of BaTi0.8Fe0.2O3 powder (0.05–0.2 g with a step of 0.05 g) for ∼5-mg/L concentrated MB dye. The treated water was further used as a growth parameter and phytotoxicity analysis through germination index on the wheat seeds. Lastly, the BaTi1−xFexO3 compositions (for x = 0, 0.1, and 0.2) were explored for water cleaning applications under real-time solar irradiation. 相似文献
We are interested in modeling behaviors and verifying properties of systems in which time and concurrency play a crucial role. We introduce a model of distributed automata which are equipped with event clocks as in Alur et al. (Theor Comput Sci 211:253–273, 1999), which we call Event Clock Message Passing Automata (ECMPA). To describe the behaviors of such systems we use timed partial orders (modeled as message sequence charts with timing). Our first goal is to extend the classical Büchi-Elgot-Trakhtenbrot equivalence to the timed and distributed setting, by showing an equivalence between ECMPA and a timed extension of monadic second-order (MSO) logic. We obtain such a constructive equivalence in two different ways: (1) by restricting the semantics by bounding the set of timed partial orders; (2) by restricting the timed MSO logic to its existential fragment. We next consider the emptiness problem for ECMPA, which asks if a given ECMPA has some valid timed execution. In general this problem is undecidable and we show that by considering only bounded timed executions, we can obtain decidability. We do this by constructing a timed automaton which accepts all bounded timed executions of the ECMPA and checking emptiness of this timed automaton. 相似文献