Influence of Different Additives on the Interaction of Quinolone Antibiotic Drug with Surfactant: Conductivity and Cloud Point Measurement Study

Conductometric and cloud point (CP) measurement studies have been performed to investigate the interaction of tetradecyltrimethylammonium bromide (TTAB) and Triton® X-100 (TX-100) with ciprofloxacin hydrochloride (CFH) in different solvents over the temperature range of 295.15–315.15 K. CFH is used for the treatment of various bacterial infections. The observed critical micelle concentration (CMC) values of TTAB were found to be reduced in the presence of electrolytes (Na₂SO₄/Na₃PO₄), and this reduction proceeds with the elevation of salt concentration. The order of the CMC of TTAB follows the trend: > >. The observed CMC values of TTAB were found to increase with increasing temperature and decrease with increasing concentration of CFH in aqueous medium. The values of Gibbs free energy of micellization () for the TTAB/TTAB + CFH mixture were found to be negative, implying spontaneous micellization. The estimated CP of TX-100 decreases with increasing concentration of TX-100 in aqueous medium. The CP values first decrease with increasing concentration of CFH and then increase at higher concentration of CFH almost in all cases investigated. The values of free energy of clouding were found to be positive in all cases studied implying that phase separation of TX-100 was nonspontaneous. The other thermodynamic parameters associated with the micellization of TTAB and the phase separation of TX-100 were estimated and explained.     

Case report: possible Lyme endocarditis

A 56-year-old male presented with clinical and serological data suggestive of Lyme disease. The patient was found to have an aortic valvular vegetation by transesophageal echocardiography. This report represents the first case of Lyme disease with possible valvular involvement.     

Enzymatic Synthesis of Glucose- and Xylose Laurate Esters Using Different Acyl Donors,Higher Substrate Concentrations,and Membrane Assisted Solvent Recovery

Glucose- and xylose laurate esters are enzymatically synthesized using equimolar substrate concentrations in 2-methyl-2-butanol, comparing free lauric acid with methyl- and vinyl-laurate as acyl donors. All reactions result in ≥70% acyl donor conversions after 72 h but the activated donors are also partially hydrolyzed to lauric acid, highlighting the difficulty in controlling water presence in this particular reaction system. The esterification of xylose generates a complex product profile, with several regioisomers of monoesters and diesters. The esterification of glucose is quite selective, forming mainly the 6-O monoester (≥96%) with a small presence of two diester isomers (4%). Increasing substrate concentration up to 800 millimoles kg⁻¹ results in lower conversion values (down to 58%) but shows that the reaction proceeds successfully even in the presence of high amounts of insoluble glucose. However, the reaction is less selective and the proportion of diester increases, becoming up to 46% (molar fraction) of the final product. Solvent recovery after esterification can be achieved by organic solvent nanofiltration through a polymeric membrane able to retain ≥80% of all reaction substrates and products. Practical Applications: The use of high substrate concentrations during the enzymatic synthesis of sugar ester biosurfactants leads to product titers that are more industrially appealing, without the need to find a solvent that can solubilize all initial substrate. The sustainability of the enzymatic conversion at mild temperatures can be enhanced by recycling of the reaction solvent through organic solvent nanofiltration, an energy efficient alternative to other traditional methods like distillation.     

Structural integrity assessment of the containment structure of a pressurised heavy water nuclear reactor using impact echo technique

The impact echo technique is based on the use of transient stress waves for non-destructive detection of flaws in concrete structures. Impact-echo testing has been carried out for assessment of the structural integrity of the ring beam of a pressurised heavy water nuclear reactor. In order to develop the test procedure for carrying out impact echo testing, mock up calibration blocks were made. The detectability of the impact echo system has also been established in terms of the depth and the lateral dimension of the detectable flaw for the ring beam under consideration. Based on the optimised test parameters identified with the help of the studies carried out on the mock up blocks, impact echo testing was carried out on the ring beam of the reactor containment structure, for assessing its structural integrity.     

The mechanical properties of epoxy resins

Crack propagation in a series of epoxy resins described in Part 1 has been studied as a function of testing rate and temperature. It has been found that crack propagation is continuous at low temperatures but that as the temperature is raised the mode of propagation becomes unstable (stick/slip). Features on the fracture surfaces at the crack arrest lines have been shown to be of the same dimensions as those expected for a Dugdale plastic zone. It has been suggested that the slip process takes place by slow growth of a crack through the plastic zone followed by rapid propagation through virgin material. It has been shown that the stick/slip behaviour is due to blunting of the crack which is controlled by the yield behaviour of the resin. A unique fracture criterion has been shown to be applicable to epoxy resins which is that a critical stress of the order of three times the yield stress must be achieved at a critical distance ahead of the crack. Electron microscope replicas of the fracture surfaces have been obtained and an underlying nodular structure can be resolved. However, no direct correlation between the nodule size and fracture properties has been found.     

Crack propagation in and fractography of epoxy resins

The relationship between the stability of crack propagation in, and the fracture surface appearance of, DGEBA epoxy resins cured with TETA has been investigated using a linear elastic fracture mechanics approach. In particular, the effect of varying the amount of curing agent and curing conditions and altering external variables such as testing rate, temperature and environment have been studied. Under certain conditions, propagation is found to be stable and fracture surfaces have a smooth appearance. Under other conditions the cracks propagate in an unstable stick-slip manner. In this case, arrest lines can be seen on the fracture surfaces and their intensity and roughness increases with the magnitude of the crack jumps. The roughness of the fracture surfaces has been measured using a Talysurf and this has been shown to be due principally to deviation of the cracks from the original fracture plane rather than any gross plastic deformation.     

Study of the dimensional instabilities of laminated polypropylene films during heating treatments

Ensuring the geometrical stability of organic coatings is a key challenge for steel/polymer composites produced by the automotive industry to reduce the cars' weight. During the thermal treatment of painting, which exceeds the melting temperature of the organic part of the laminated film, polymer shrinkage may occur. It induces uncovered parts of the steel sheet which would present negative corrosion behavior in use. Two original and innovative experiments were presented. They enable to measure the deformation induced by the shrinkage and then to identify the microstructural mechanisms responsible for its appearance. Main results show strong influences of the macromolecular chains orientation induced by the film extrusion process and of the postheating parameters used to perform the painting curing. Raman spectroscopy and differential scanning calorimetry are used both to perform analysis of the microstructure evolution during heating treatments in terms of crystals melting, crystalline macromolecular chains disorientation, and volume damage healing. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of diethyl ether blended with neem oil methyl esters in CI engine

Vegetable oils are now considered to be a potential alternative that can be used in place of partial or total substitution of diesel fuels. In this study, we used diethyl ether as an oxygenated additive to investigate the possible use of higher percentages of biodiesel in an unmodified diesel engine. Neem oil was selected for biodiesel production. The tests were performed at a steady-state condition in a single-cylinder constant speed DI diesel engine. The combustion process involved in diesel engine would be improved and the particulate matter would be reduced if these biodiesels are blended. An experimental investigation is carried out to establish the emission characteristics of a direct injection diesel engine using diethyl ether as additive in Neat Neem oil Biodiesel. Emissions of hydro carbon oxides of nitrogen and carbon monoxide significantly reduced by adding diethyl ether into neem oil biodiesel at 10% and 20% on volume basis.