Surface integrity characterization of manufactured component is very important as it significantly affects the in-service performance of the component. Till now, surface integrity was evaluated using conventional measurement technique like microhardness tester, X-ray diffraction, optical microscopy and surface roughness tester. But, this technique being laboratory based cannot be used for in-service monitoring of the surface integrity. The present study focuses on the characterization of surface integrity upon electric discharge machined sample using non-destructive magnetic Barkhausen noise technique. Electric discharge machining was performed in die-sinking mode on die steel using copper–tungsten electrode (negative polarity). Experiment was performed by selecting different levels of peak current, gap voltage and pulse on time. Surface integrity characteristics like microhardness change, residual stress, microstructural alteration and surface roughness were analysed using microhardness tester, X-ray diffraction, optical microscopy and surface roughness tester, respectively, and were then correlated with magnetic parameter like root mean square value and peak value obtained from Barkhausen noise signal. The results show a good correlation between magnetic parameter (RMS and Peak value) of Barkhausen noise with the microhardness and surface roughness of the machined sample.
The present study was aimed to utilize low‐cost alumina (Al2O3) nanoparticles for improving the heat transfer behavior in an intercooler of two‐stage air compressor. Experimental investigation was carried out with three different volume concentrations of 0.5%, 0.75%, and 1.0% Al2O3/water nanofluids to assess the performance of the intercooler, that is, counterflow heat exchanger at different loads. Thermal properties such as thermal conductivity and overall heat transfer coefficient of nanofluid increased substantially with increasing concentration of Al2O3 nanoparticles. Specific heat capacity of nanofluids were lower than base water. The intercooler performance parameters such as effectiveness and efficiency improved appreciably with the employment of nanofluid. The efficiency increased by about 6.1% with maximum concentration of nanofluid, that is, 1% at 3‐bar compressor load. It is concluded from the study that high concentration of Al2O3 nanoparticles dispersion in water would offer better heat transfer performance of the intercooler. 相似文献
In the present study, Karso watershed of Hazaribagh, Jharkhand State, India was divided into 200 × 200 grid cells and average
annual sediment yields were estimated for each grid cell of the watershed to identify the critical erosion prone areas of
watershed for prioritization purpose. Average annual sediment yield data on grid basis was estimated using Universal Soil
Loss Equation (USLE). In general, a major limitation in the use of hydrological models has been their inability to handle
the large amounts of input data that describe the heterogeneity of the natural system. Remote sensing (RS) technology provides
the vital spatial and temporal information on some of these parameters. A recent and emerging technology represented by Geographic
Information System (GIS) was used as the tool to generate, manipulate and spatially organize disparate data for sediment yield
modeling. Thus, the Arc Info 7.2 GIS software and RS (ERDAS IMAGINE 8.4 image processing software) provided spatial input
data to the erosion model, while the USLE was used to predict the spatial distribution of the sediment yield on grid basis.
The deviation of estimated sediment yield from the observed values in the range of 1.37 to 13.85 percent indicates accurate
estimation of sediment yield from the watershed. 相似文献
This study assesses snow response in the Assiniboine-Red River basin, located in the Lake Winnipeg watershed, due to anthropogenic climate change. We use a process-based distributed snow model driven by an ensemble of eight statistically downscaled global climate models (GCMs) to project future changes under policy-relevant global mean temperature (GMT) increases of 1.0 °C to 3.0 °C above the pre-industrial period. Results indicate that basin scale seasonal warmings generally exceed the GMT increases, with greater warming in winter months. The majority of GCMs project wetter winters and springs, and drier summers, while autumn could become either drier or wetter. An analysis of snow water equivalent (SWE) responses under GMT changes reveal higher correlations of snow cover duration (SCD), snowmelt rate, maximum SWE (SWEmax) and timing of SWEmax with winter and spring temperatures compared to precipitation, implying that these variables are predominantly temperature controlled. Consequently, under the GMT increases from 1.0 °C to 3.0 °C, the basin will experience successively shorter SCD, slower snowmelt, smaller monthly SWE and SWEmax, earlier SWEmax, and a transition from snow-dominated to rain-snow hybrid regime. Further, while the winter precipitation increases for some GCMs compensate the temperature-driven changes in SWE, the increases for most GCMs occur as rainfall, thus limiting the positive contribution to snow storage. Overall, this study provides a detailed diagnosis of the snow regime changes under the policy-relevant GMT changes, and a basis for further investigations on water quantity and quality changes. 相似文献
Silicon - This paper examines, an electrostatically configured Nano-Tube Tunnel Field-Effect Transistor (ED-NTTFET). During the fabrication process, different charges such as fixed charge, oxide... 相似文献
Axial plasma spray is one of the thermal spray techniques to deposit multifunctional advanced coatings. The present work explores the use of this process to deposit thin, continuous, and adherent Ca5 (PO4)3OH (hydroxyapatite, HAp) coatings and characterize its microstructure, phases, hardness and adhesion strength. Three different suspension-deposited HAp coatings were investigated and compared with powder-deposited HAp coating on a Ti6Al4V substrate. The effect of mean solute particle size and solid-loading in the suspension has been explored on the evolution of microstructure, phase content and mechanical properties of axial suspension plasma sprayed (ASPS) coatings. Phase-characterization has shown retention of hydroxyapatite phase and coating crystallinity in the deposited coatings, whereas the adhesion strength of the HAp coating decreased from ~40 MPa to ~13 MPa when bioglass was added to the feedstock material. The lower solid load content and lower mean solute particle size in the suspension were found to be beneficial in achieving porous, rougher, and well-adhering coatings. This work concludes that ASPS can potentially deposit thin HAp coatings (< 50 μm) with high adhesion strength. 相似文献
This paper reports tribological characterization of titanium based coatings ion bonded on steel balls for automotive applications using exhaust gas recirculation (EGR). It is well known that lubricating oil drawn from EGR operated engine is contaminated with soot and higher amounts of wear debris compared to non-EGR operated engine. In this study, steel balls coated with TiN, TiAlN and TiCN are investigated in both fresh lubricating oil and EGR stressed oil for a comparative assessment of their wear characteristics in two mediums. Normal load was applied on the samples, tested against a rotating cast iron disk, simulating ring-liner interaction. In each experiment, about one quarter of disk was dipped in the oil (a) to ensure the presence of a thin oil film on the disk-ball interface during the experiment, and (b) to avoid exposure of the worn surface to atmospheric air. The results reveal that the wear rates of the coatings based on the change in the scar diameters of the samples, tested in EGR oil was 2-4 times higher than that of fresh lubricating oil. It was found that despite lowest hardness, TiN coated samples showed smaller scar diameters than TiAlN and TiCN coated samples in both lubricating oil environments. A simple geometric model was used to calculate the thickness of the coating removed as a function of the test duration. Results show that TiN coatings last for 120 min in fresh oil as compared to 30 min in the EGR oil under normal loading, whereas TiAlN and TiCN coating last for 60 and 30 min respectively in fresh oil and wear out in 15 min in EGR oil. 相似文献