Surface Integrity Assessment Upon Electric Discharge Machining of Die Steel Using Non-Destructive Magnetic Barkhausen Noise Technique

Surface integrity characterization of manufactured component is very important as it significantly affects the in-service performance of the component. Till now, surface integrity was evaluated using conventional measurement technique like microhardness tester, X-ray diffraction, optical microscopy and surface roughness tester. But, this technique being laboratory based cannot be used for in-service monitoring of the surface integrity. The present study focuses on the characterization of surface integrity upon electric discharge machined sample using non-destructive magnetic Barkhausen noise technique. Electric discharge machining was performed in die-sinking mode on die steel using copper–tungsten electrode (negative polarity). Experiment was performed by selecting different levels of peak current, gap voltage and pulse on time. Surface integrity characteristics like microhardness change, residual stress, microstructural alteration and surface roughness were analysed using microhardness tester, X-ray diffraction, optical microscopy and surface roughness tester, respectively, and were then correlated with magnetic parameter like root mean square value and peak value obtained from Barkhausen noise signal. The results show a good correlation between magnetic parameter (RMS and Peak value) of Barkhausen noise with the microhardness and surface roughness of the machined sample.

     

Efficiency and effectiveness enhancement of an intercooler of two‐stage air compressor by low‐cost Al2O3/water nanofluids

The present study was aimed to utilize low‐cost alumina (Al₂O₃) nanoparticles for improving the heat transfer behavior in an intercooler of two‐stage air compressor. Experimental investigation was carried out with three different volume concentrations of 0.5%, 0.75%, and 1.0% Al₂O₃/water nanofluids to assess the performance of the intercooler, that is, counterflow heat exchanger at different loads. Thermal properties such as thermal conductivity and overall heat transfer coefficient of nanofluid increased substantially with increasing concentration of Al₂O₃ nanoparticles. Specific heat capacity of nanofluids were lower than base water. The intercooler performance parameters such as effectiveness and efficiency improved appreciably with the employment of nanofluid. The efficiency increased by about 6.1% with maximum concentration of nanofluid, that is, 1% at 3‐bar compressor load. It is concluded from the study that high concentration of Al₂O₃ nanoparticles dispersion in water would offer better heat transfer performance of the intercooler.     

Computer Aided Tolerance assignment

Tolerances are basic to the production of every part. This is because perfect parts cannot be produced with existing processes and machines. The determination of tolerances for the individual parts of a functional assembly is critical, but not trivial. Numerous approaches are suggested in past literature for (analytical) tolerance allocation. With the advent of total automation, more attempts are being made to computerize manual design tasks. Tolerance design, assignment and allocation can also be fully automated if the assembly function can be estimated by the computer.

In the present paper, an attempt is made to computerize tolerance assignment. A simple example of a two piece assembly, viz., a fit, is used to demonstrate the developed methodology. A feature extraction is first performed from both detail and assembly drawings. Then, probable assembly interfaces are determined using a rule based procedure. Consequently, tolerances are assigned to the basic dimensions of each feature and to the assembly interfaces using a tolerance database and user interaction. More complex analysis for tolerance allocation is also under study.     

Identification of critical erosion prone areas in the small agricultural watershed using USLE,GIS and remote sensing

In the present study, Karso watershed of Hazaribagh, Jharkhand State, India was divided into 200 × 200 grid cells and average annual sediment yields were estimated for each grid cell of the watershed to identify the critical erosion prone areas of watershed for prioritization purpose. Average annual sediment yield data on grid basis was estimated using Universal Soil Loss Equation (USLE). In general, a major limitation in the use of hydrological models has been their inability to handle the large amounts of input data that describe the heterogeneity of the natural system. Remote sensing (RS) technology provides the vital spatial and temporal information on some of these parameters. A recent and emerging technology represented by Geographic Information System (GIS) was used as the tool to generate, manipulate and spatially organize disparate data for sediment yield modeling. Thus, the Arc Info 7.2 GIS software and RS (ERDAS IMAGINE 8.4 image processing software) provided spatial input data to the erosion model, while the USLE was used to predict the spatial distribution of the sediment yield on grid basis. The deviation of estimated sediment yield from the observed values in the range of 1.37 to 13.85 percent indicates accurate estimation of sediment yield from the watershed.     

Support vector regression for determining the minimum zone sphericity

Several methods have been investigated to determine the deviation of manufactured spherical parts from ideal geometry. One of the most popular is the least squares technique, which is still widely employed in coordinate measuring machines used by industries. The least squares algorithm is optimal under the assumption that the data set is very large and has the inherent disadvantage of overestimating the minimum tolerance zone, resulting sometimes in the rejection of good parts. In addition, it requires that the data be distributed normally. The support vector regression approach alleviates the necessity for these assumptions. While most fitting algorithms in practice today require that the sampled data accurately represent the surface being inspected, support vector regression provides a generalization over the surface. We describe how the concepts of support vector regression can be applied to the determination of tolerance zones of nonlinear surfaces; to demonstrate the unique potential of support vector machine algorithms in the area of coordinate metrology. In specific, we address part quality inspection of spherical geometries.