Ecophysiology and niche differentiation of Nitrospira-like bacteria, the key nitrite oxidizers in wastewater treatment plants.

Nitrite-oxidizing bacteria of the genus Nitrospira are key nitrifiers in wastewater treatment plants. Pure cultures of these organisms are unavailable, but cultivation-independent molecular methods make it possible to detect Nitrospira-like bacteria in environmental samples and to investigate their ecophysiology. Comprehensive screening of natural and engineered habitats and of public databases for 16S rRNA sequences of Nitrospira-like bacteria revealed a surprisingly high biodiversity in the genus Nitrospira, which comprises at least four phylogenetic sublineages. All Nitrospira-like bacteria detected in wastewater treatment plants belonged to the sublineages I and II. Subsequently, the population dynamics of different Nitrospira-like bacteria were monitored, by quantitative fluorescence in situ hybridization with rRNA-targeted probes, confocal laser scanning microscopy and digital image analysis, during incubation of nitrifying activated sludge in media containing different nitrite concentrations. These experiments showed that Nitrospira-like bacteria, which were affiliated with the phylogenetic sublineages I or II of the genus Nitrospira, responded differently to nitrite concentration shifts. Previously unknown properties of Nitrospira-like bacteria were discovered in the course of an environmental genomics project. Implications of the obtained results for fundamental understanding of the microbial ecology of nitrite oxidizers as well as for future improvement of nutrient removal in wastewater treatment plants are discussed.     

Application of novel extractants for actinide(III)/ lanthanide(III) separation in hollow-fibre modules

Separation tests using hollow-fibre modules were performed for the difficult selective extraction of trivalent actinides over fission lanthanides from acidic media. This article shows that with 2,6-di(5,6-dipropyl-1,2,4-triazin-3-yl)pyridine as the extractant, up to 94% americium could be extracted from 1.0 kmol/m³ HNO₃, with minimal lanthanide co-extraction. Using a synergistic mixture of bis(chlorophenyl)dithiophosphinic acid and tri-n-octyl phosphine oxide, tests were performed on extraction, lanthanide scrubbing and stripping. In the extraction test, up to 99.99% americium could be extracted from 0.5 kmol/m³ HNO₃, with approximately one third of the lanthanides being co-extracted. Mass transfer calculations using a consistent set of input data showed good agreement with the experiments.     

Biochemical identification of transmembrane segments of the Ca(2+)-ATPase of sarcoplasmic reticulum

The transmembrane segments of sarcoplasmic reticulum Ca(2+)-ATPase were determined by trypsinization of cytoplasmic side-out intact sarcoplasmic reticulum vesicles. The membrane portion of tryptic digest comprising the transmembrane fragments, joined by the intravesicular segments, was separated by sodium dodecyl sulfate-polyacrylamide gel electrophoresis after labeling with fluorescein 5-maleimide in the presence of sodium dodecyl sulfate. In this way, seven fluorescent bands of tryptic fragments below 11 kDa were observed which were derived from 4 pairs of membrane spanning segments and one hydrophobic sequence at the C-terminal end. Two peptides of 10.8 and 10.6 kDa had the identical N-terminal sequence beginning at Glu826, representing the transmembrane segments M7 and M8 and their connecting loop. A band at 8.1 kDa contained one peptide beginning at Tyr36 (M1/loop/M2). A 7.7-kDa peptide starting at Leu253 (M3/loop/M4) and a 7.3-kDa peptide beginning at Ala752 (M5/loop/M6) were also observed. A band at 6.7 kDa contained two peptides, one beginning at Ser48 (M1/loop/M2) and another beginning at Tyr763 (M5/loop/M6). In addition, a 4-kDa peptide beginning at Met925 was observed. The size of this peptide did not allow for a complete pair of transmembrane segments, but this peptide could have been derived from trypsinolysis between the last pair of membrane spanning segments. These data therefore provide biochemical evidence for at least 8 transmembrane segments and perhaps two more at the C-terminal end of the enzyme.     

Retention of Escherichia coli in municipal sewage by means of planted soil filters in two-stage pilot plant systems.

Different types of constructed wetlands in a pilot-plant system were fed with identical municipal waste water to compare the sanitisation process in two-stage systems. With combinations of a vertical and a horizontal flow filter an E. coli reduction of 5 log10 with an E. coli influent concentration of 10(7) MPN/100 ml was achieved. Using different filter materials in each stage the total performance of the two-stage system was independent from the sequence of these materials. However, using coarser filter material in the first stage makes the filter less prone to clogging and is thus the preferential option with regard to operational reliability.     

Production of maraging steel grades and the influence of specified and nonspecified elements for special applications

The material properties of maraging steels are greatly affected by the alloy and inclusion content and hence by the production route. This paper describes various past and current production routes at Böhler Edelstahl GmbH and the effect of these routes on the specified element (alloy) and non-specified element (inclusion) contents. Non-metallic inclusions were investigated by EDX analysis. The effects of various alloying and tramp elements on the material properties are presented as a statistical evaluation of previous melts. Nitrogen solubility was calculated with Thermo–Calc for maraging steel Mat.-No. 1.6354 and the precipitation of nitrides is discussed. A proposal is made for the production of melts with improved properties.     

Mitteilungen der Gesellschaft für Informatik 194. Folge

Ohne Zusammenfassung     

3D Hair sketching for real-time dynamic & key frame animations

Physically based simulation of human hair is a well studied and well known problem. But the “pure” physically based representation of hair (and other animation elements) is not the only concern of the animators, who want to “control” the creation and animation phases of the content. This paper describes a sketch-based tool, with which a user can both create hair models with different styling parameters and produce animations of these created hair models using physically and key frame-based techniques. The model creation and animation production tasks are all performed with direct manipulation techniques in real-time.