Structure and mechanical properties of polyethylene-fullerene composites

The microhardness of films of fullerene-polyethylene composites prepared by gelation from semidilute solution, using ultrahigh molecular weight polyethylene (PE) (6×10⁶), has been determined. The composite materials were characterized by optical microscopy and X-ray diffraction techniques. The microhardness of the films is shown to increase notably with the concentration of fullerene particles within the films. In addition, a substantial hardening of the composites is obtained after annealing the materials at high temperatures (T _a=130 °C) and long annealing times (t _a=10⁵s). The hardening of the composites with annealing temperature has been identified with the thickening of the PE crystalline lamellae. Comparison of X-ray scattering data and the microhardness values upon annealing leads to the conclusion of phase separation of C₆₀ molecules from the polyethylene crystals within the material. The temperature dependence is discussed in terms of the independent contribution of the PE matrix of the C₆₀ aggregates to the hardness value.     

EEPROM transistor fabricated with stacked SiOx LPCVDfilms

The key fabrication steps and the write/erase characteristics of a new memory metal-insulator-silicon transistor are presented. The memory cell is composed of a single silicon gate and a stacked SiO_x LPCVD film as an active memory film. With this new arrangement, the memory device shows excellent endurance     

Effect of local alloy disorder on the emission kinetics of deep donors (DX centers) in AlxGa1-xAs

In this paper we summarize our recent studies of the effects of local alloy disorder on the properties ofDX levels. A single emission rate is observed in GaAs where all Si-donors have identical local environments. In contrast, three discrete emission rates are observed in dilute AlGaAs alloys, suggesting that the group IV donor moves towards the interstitial site, thereby “selecting” three of the twelve surrounding group III atoms. We present evidence for an ordering of theDX levels consistent with Morgan’s model of a deepening potential well for theDX level as Al atoms are subsequently substituted for Ga atoms near the relaxed donor. These conclusions are consistent with earlier calculations of Chadi and Chang.     

Novel aspects of the microstructure of PP/PA blends prepared by reactive compounding as studied by microhardness

The microhardness of injection-moulded i-polypropylene/polyamide (iPP/PA) blends prepared by reactive compounding was determined. The formulation rules and processing technology for the preparation of these alloys was reported previously. iPP/PA compositions between 100/0 and 50/50 using functionalized PP with various degrees of mainchain grafting, were investigated. It is shown that the deviation of microhardness from the additivity law of the single components is mainly due to a decrease in the crystallinity of the iPP phase. The results are discussed in the light of the microstructural variations as revealed by X-ray diffraction methods.     

Conductive PE-carbon composites by elongation flow injection moulding

In Part 1 and Part 2 of this paper the preparation of linear polyethylene (PE)-carbon black processed composites with conducting electrical properties was examined by means of elongation flow injection moulding. Mould geometry was optimized in the form of oriented double-armed bars so as to give enhanced mechanical properties combined with a high degree of electrical homogeneity. The present paper deals with composites using a high molecular weight PE matrix. It is shown that the injection-moulded composite material exhibits not only a lower percolation threshold, _c, than the conventionally pressure-moulded isotropic sample, but also conductivities two to three orders of magnitude larger than the latter. The radial and axial conductivity profiles, for concentrations well above _c, are discussed in the light of the molecular orientation variations across the bars as determined by birefringence. A segregation of primary filler particles, during flow-induced orientation, into axial channels has been shown to explain the enhancement of conductivity detected in the injected mouldings. In addition, for filler concentrations near 7%, -profile analysis indicates the development of a uniform conductive-stiff inner cylinder, several millimetres wide, homogeneously extending along the full length of the injected material.     

Structure development in amorphous starch as revealed by X‐ray scattering: Influence of the network structure and water content

The evolution of the amorphous structure of starch was characterized during the drying process by real‐time X‐ray wide‐angle scattering. The X‐ray diffractograms of injection‐molded starch show two superposed, rather broad, scattering maxima indicative of noncrystalline structures. The location of the two peaks has been associated to disordered starch single helices. A third maximum that arises upon drying the material in vacuum is associated to the scattering emerging from regions containing double helices. A model for the starch network is proposed, assuming a primary and a secondary component. The wider, temperature stable component appearing first, is correlated to the entanglement network of the melt. The narrower network component, which is created later, at lower temperature (secondary network), is explained by the formation of double helix regions that densify the wider primary network. The secondary network is increased strongly by the drying process. X‐ray experiments performed during the penetration of water, provoking a higher molecular mobility, reveal a better‐packed helical structure that becomes the precursor of a double helix crystalline formation. When temperature increases, the secondary network is dissolved and water molecules arrange themselves in better‐organized crystals as strongly bound crystal water. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1880–1886, 2006     

Microhardness studies of PMMA/natural rubber blends

The microhardness, H, of PMMA/natural rubber blends, prepared following the solution method has been investigated by means of the microindentation technique. Hardness changes are correlated with the variation of the glass transition temperature. The influence of temperature and degree of deformation on H were additionally examined. The inclusion of rubber particles in the PMMA matrix is shown to soften the blends. The variation of the micromechanical property at the phase boundary of polymer/rubber particle has been studied. Results reveal that H drastically drops at the interphase. In the case of the drawn materials, the indentation anisotropy (ΔH) is shown to gradually increase with the draw ratio, where ΔH is found to be higher for the PMMA/rubber blend than for the original PMMA. This result is explained by the higher orientation of the PMMA molecules near the periphery of stretched rubber particles. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 205–210, 2004     

Iron species incorporated over different silica supports for the heterogeneous photo-Fenton oxidation of phenol

Iron-containing catalysts have been prepared following different synthesis routes and silica supports (amorphous, zeolitic and mesostructured materials). Activity and stability of these materials were assessed on the photo-Fenton degradation of phenolic aqueous solutions using near UV irradiation (higher than 313 nm) at room temperature and initial neutral pH. Their catalytic performance was monitored in terms of phenol and total organic carbon (TOC) conversions. Aromatic compounds and carboxylic acids as by-products coming from incomplete mineralization of phenol as well as the efficiency of each catalytic system in the use of the oxidant were also studied. Stability of the materials throughout the photo-Fenton reaction was evaluated in terms of metal leachibility. Activity and stability depend on the environment of iron species and features of silica support. The evolution of pH with the reaction time and their relationship with TOC degradation and leaching degree has been discussed. A nanocomposite material of crystalline iron oxides supported over mesostructured SBA-15 material is shown the most successful catalyst for degradation of phenolic aqueous solutions by photo-Fenton processes, achieving an outstanding overall catalytic performance accompanied with a noteworthy stability.     

Correlation of microhardness and morphology in injection-moulded poly(ethylene terephtalate)

Microindentation hardness has been applied to a series of injection-moulded poly(ethylene terephtalate) samples prepared using a range of mould temperatures, T _c. The morphology of the samples was characterized by X-ray diffraction and differential scanning calorimetry. Depending on T _c, it is shown that microhardness is lower at the surface than in the core of the mouldings. Results are discussed in terms of the volume fraction of spherulites filling the mouldings which is shown to be dependent upon T _c. The influence of an annealing treatment on the properties of the mouldings is examined. The microhardness values are correlated with the thickness and with the surface free energy of the lamellar crystals. The results obtained indicate that increasing annealing temperatures first leads to an increase and then to a sudden decrease of hardness. The latter can be associated with the changes occurring in the number of defects on the crystal's surface.