A new Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor

A new and interesting Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor has been fabricated and studied. The steady-state and transient responses with different hydrogen concentrations has been measured at various temperatures. Based on the large Schottky barrier height and presence of oxide layer, the studied device exhibits a high hydrogen detection sensitivity and wide temperature operating regime. The studied device exhibits the low-leakage current and obvious current changes when exposed to hydrogen-contained gas. Even at room temperature, a very high hydrogen detection sensitivity of 155.9 is obtained when a 9090 ppm H/sub 2//air gas is introduced. Furthermore, when exposed to hydrogen-contained gas at 95/spl deg/C, both the forward and reverse currents are substantially increased with increased hydrogen concentration. In other words, the studied device can be used as a hydrogen sensor under the applied bidirectional bias. Under the applied voltage of 0.35 V and 9090 ppm H/sub 2//air hydrogen ambient, a fast adsorption response time about 10 s is found. The transient and steady-state characteristics of hydrogen adsorption are also investigated.     

A novel InP/InGaAs TEBT for ultralow current operations

A novel InP/InGaAs tunneling emitter bipolar transistor (TEBT) is fabricated and demonstrated. The studied device exhibits a very small collector-emitter offset voltage of 40 mV and an extremely wide operation regime. The operation region is larger than 11 decades in magnitude of collector current (10/sup -12/ to 10/sup -1/A). A current gain of 3 is obtained even if the device is operated at an ultralow collector current of 3.9 /spl times/ 10/sup -12/A (1.56 /spl times/ 10/sup -7/A/cm/sup 2/). Furthermore, the common-emitter breakdown voltage of the studied device is higher than 2 V. Consequently, the studied device shows a promise for low supply voltage, and low-power consumption circuit applications.     

Smooth profile generation for a tile printing machine

In this paper a digital filter is proposed for the generation of smooth set points for motion control systems. The proposed nonlinear filter produces profiles with bounded velocity and acceleration starting from rough reference signals (steps and ramps). An actual implementation of the filter for a tile printing machine is presented and experimental results are reported.     

Collision Detection and Multitone Tree Search for Multiple-Access Protocols on Radio Channels

The carrier sense multiple access with collision detection (CSMA-CD) protocol cannot be applied directly to radio channels because of the difficulty in sensing remote carrier in the presence of local transmission. Only recently, a new protocol called the CSMA with timesplit collision detection (CSMA-TCD) was introduced to overcome this problem on radio channels. This paper presents an extension of the CSMA-TCD protocol, called CSMA-TCD with multitone tree search (CSMA-TCD-MTTS). In CSMA-TCD, a preamble is transmitted before data transmission. For CSMA-TCD-MTTS, the preamble is modulated with one out ofNtones. In case of a collision, a resolution algorithm splits the terminals involved into anN-degree tree according to the tone chosen. This paper presents the throughput and approximate delay analysis of the CSMA-TCD-MTTS protocol.     

Tunable laser-based design and analysis for fractional lambda switches

Fractional lambda switching (FlambdaS) is a novel approach for traffic management over all-optical networks with sub-wavelength provisioning capability. The unique characteristic of FlambdaS is the utilization of UTC (coordinated universal time) for switching with minimum or no buffers. Several central research issues are still open in FlambdaS and need to be formally defined and analyzed. In this paper, we introduce three novel switch designs that are based on the use of tunable lasers (which can be replaced in the future with wavelength converters). First, the paper presents analytical results of scheduling feasibility, which measures the total number of possible different schedules for each switch design. Then it is shown that the architecture with the highest scheduling feasibility is strictly non blocking in the space domain. Next, the paper provides a closed form analysis of the blocking probability in the time domain, which is applicable for any strictly non-space blocking switch, using combinatorics. In addition, the paper provides measures of the switching hardware complexity, which, for the strictly non-blocking architecture, has the same switching complexity as Clos interconnection network, i.e., O(N'radic(N')) where N' is the number of optical channels.     

Synthetic approach to optimal filtering

As opposed to the analytic approach used in the modern theory of optimal filtering, a synthetic approach is presented. The signal/sensor data, which are generated by either computer simulation or actual experiments, are synthesized into a filter by training a recurrent multilayer perceptron (RMLP) with at least one hidden layer of fully or partially interconnected neurons and with or without output feedbacks. The RMLP, after adequate training, is a recursive filter optimal for the given structure, with the lagged feedbacks carrying the optimal conditional statistics at each time point. Above all, it converges to the minimum variance filter as the number of hidden neurons increases. We call such an RMLP a neural filter. Simulation results show that the neural filters with only a few hidden neurons consistently outperform the extended Kalman filter and even the iterated extended Kalman filter for the simple nonlinear signal/sensor systems considered.     

Colloidal silica removal in coagulation processes for wastewater reuse in a high-tech industrial park.

Four experiments of coagulation and flocculation were conducted to investigate the characteristics of colloidal silica removal in a high-tech industrial wastewater treatment plant for reclamation and reuse of the effluent. Experimental results illustrated that poly-aluminium chloride (PACl) showed higher performances on colloidal silica removal than alum. Interestingly, the two coagulants demonstrated the same capacity on silica removal. The specific silica removal capacity was approximately 0.135 mg SiO2/mg Al2O3 when the dosage of coagulants was in the range 30-150 mg/L Al2O3. In addition, the silica was reduced significantly at the condition of pH above 8. Experimental data implied that precipitation of aluminium flocs was the major mechanism for colloid silica removal in PACl and alum coagulation, besides, charge adsorption was also important for improving removal efficiency. Moreover, the addition of polyacrylic acid (PAA) as a flocculant could slightly advance silica removal in the PACl coagulation. The combined PACl/PAA/flocs coagulation was effective for the removal of colloidal silica, soluble COD, and turbidity and also suitable as a pretreatment unit in wastewater reclamation and reuse processes.     

Dissolution Behavior of Griseofulvin Solid Dispersions Using Polyethylene Glycol, Talc, and Their Combination as Dispersion Carriers

Griseofulvin solid dispersions were prepared using polyethylene glycol 6000 (PEG), talc, and their combination as carriers by the solvent method. The dissolution of griseofulvin from these dispersions was studied. It was found that in these carriers the drug dissolution rate was a function of drug loading. The dissolution rate from dispersions prepared using PEG was similar to that from PEG/talc dispersions, especially at a low percentage of drug loading. Dispersions of PEG and PEG/talc provided dissolution rates faster than those from dispersions of talc. The incorporation of talc in PEG yielded dispersions with properties of less tackiness and ease for handling. Dissolution kinetics, based on the Hixson-Crowell equation, was used to determine the characteristics of griseofulvin particles in dispersions. Linear relationships were obtained for PEG and PEG/talc dispersions that indicated the presence of a uniformly sized monoparticulate system, whereas deviation from linearity was observed for talc dispersions. This appeared to be a multiparticulate system in which particles were present as free form and adsorbed form on the surface of talc.     

Synthesis and characterization of a novel proton‐exchange membrane for fuel cells operating at high temperatures and low humidities

The synthesis of a p‐toluidine/formaldehyde (PTF) resin was performed, and the effects of the molar ratio of the individual monomers and the polymerization conditions on the structure of the PTF resin were studied. Fourier transform infrared and ¹³C‐NMR spectra were used to characterize the PTF. Wide‐angle X‐ray diffraction patterns revealed the crystalline structures of various PTFs. Polarized optical microscopy revealed that the molar ratio of the monomers had a strong effect on the crystalline morphologies. A longer polymerization time turned out a polymer with a higher intrinsic viscosity and molecular weight, which led to differences in the proton conductivity. All of the PTFs showed a higher proton conductivity than a commercial Nafion membrane at 90–100°C and 0% relative humidity. The proton conductivity of the PTF series could be improved by sulfonation with sulfuric acid and could be maintained after blending with polyurethane. Pure methanol could be used as a fuel source because of the insolubility and nonwetting properties of PTF in methanol to increase the output current density for a PTF membrane electrode assembly. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Performance limitations of TDD wireless personal communications with asynchronous radio ports

A wireless personal communications system, based on a TDMA architecture, using asynchronous ports (radio base stations) and the TDD (time division duplexing) method is evaluated using computer simulations. It is shown that, without port synchronisation TDD methods cannot achieve the uplink quality obtainable by the FDD (frequency division duplexing) method.<>