Room Temperature Ferromagnetism in Co-doped CuAlO2 Nanofibers Fabricated by Electrospinning

One-dimensional, diluted magnetic semiconductor nanofibers have attracted increasing attention for their unique magnetic properties, large specific surface area, and high porosity. These qualities lead to excellent performance in magneto-optical devices, magnetic resonance imaging, ferrofluids and magnetic separation. The purpose of this study is to fabricate P-type one dimensional CuAlO2-based diluted magnetic semiconductor nanofibers. First, we fabricated Cu Al0.95Co0.05O2 nanofibers with an average diameter of 1 μm with the electrospinning method. The annealed nanofibers were thermally treated at a temperature of 1 100 ℃ and then shrunk to a diameter of about 650 nm. We used X-ray diffraction measurements and Raman spectra to confirm that the Cu Al0.95Co0.05O2 nanofibers had a single impurity free delafossite phase. The X-ray photoelectron spectroscopy analysis indicates that Co was present in the +2 oxidation state, resulting in an room temperature ferromagnetism in the Cu Al0.95Co0.05O2 fiber. This contrasts with nonmagnetism in pristine CuAlO2 fiber. The coercivity(Hc) value of 65.26 Oe and approximate saturation magnetization(Ms) of 0.012 emu/g demonstrate good evidence of ferromagnetism at room temperature for Cu Al0.95Co0.05O2 nanofibers.     

Preparation of Silver Nanowires via a Rapid,Scalable and Green Pathway

Rapid synthesis of silver nanowires(Ag NWs) with high quality and a broad processing window is challenging because of the low selectivity of the formation of multiply twinned particles at the nucleation stage for subsequent Ag NWs growth.Herein we report a systematic study of the water-involved heterogeneous nucleation of Ag NWs with high rate(less than 20 min) in a simple and scalable preparation method.Using glycerol as a reducing agent and a solvent with a high boiling point,the reaction is rapidly heated to 210 ℃ in air to synthesize Ag NWs with a very high yield in gram level.It is noted that the addition of a small dose of water plays a key role for obtaining highly pure Ag NWs in high yield,and the optimal water/glycerol ratio is0.25%.After investigating a series of forming factors including reaction temperature and dose of catalysts,the formation kinetics and mechanism of the Ag NWs are proposed.Compared to other preparation methods,our strategy is simple and reproducible.These Ag NWs show a strong Raman enhancement effect for organic molecules on their surface.     

基于状态空间法的电动机故障诊断和识别

电动机的初期故障信号一般较弱,不易辨别,而状态空间法在小信号的处理中灵敏度很高。为达到对电动机故障的诊断和识别,试图把状态空间法应用到对电动机的故障诊断中,先通过推导,从数学理论层面分析了状态空间法对于电动机故障信号的可辨别性,再使用Matlab软件搭建状态空间的辨别模型,把实验台测试的三组数据导入到模型中进行测试。测试的结果有力地证明了此方法的可行性,并能克服快速傅里叶变换(FFT)中数据采集量较大、分辨率不高的缺点。     

声波测井换能器激发响应实验研究

声波测井换能器的激发响应由换能器振动时所表现出来的动态阻抗和激发电路参数决定。而换能器的动态（阻抗）参数随压电晶体及其装配方式（力学边界条件）改变。为了测量换能器动态参数的影响，采用声波测井仪器常用的压电晶体和升压变压器，通过改变激发脉冲宽度和直流电压进行了实验，结果发现：在换能器两端的瞬态响应中，一共有三个二阶网络响应，分别对应于不同的频率。最低的一个影响声波测井波形的基线、与换能器主频接近的一个决定激发效率以及电路与压电晶体之间的匹配关系，是激发电路设计中比较关键的，其参数可以通过导纳圆测量仪器得到。     

新设备技术在催化裂化装置上的应用

文章介绍了近年来在催化裂化装置上应用的新设备、新技术,如BY型旋风分离器、BSX型旋分式三级旋风分离器、上下拱型三级旋风分离器、下拱型三级旋风分离器、SHS“自蔓延”技术、SWY外取热器、BWJ型喷嘴、自流浇注料、Actehem高耐磨衬里、弓形钢丝纤维、侧拉环锚固钉、分体可拆人孔等的结构特点及实际应用情况。     

移动机器人路径规划方法研究

移动机器人技术研究中的一个重要领域是路径规划技术，它分为基于模型的环境已知的全局路径规划和基于传感器的环境未知的局部路径规划。综述了移动机器人路径规划技术的发展现状指出了各种方法的优点与不足，最后对移动机器人路径规划技术的发展趋势进行了展望。     

A decision support system for interactive decision making - Part II: analysis and output interpretation

For pt.I see ibid., p.42-55 (2003). The development of a comprehensive decision support system, GMCR II, for the systematic study of real-world interactive decision problems is presented. The companion paper (Part I), discusses how GMCR II elicits, stores, and manages conflict models; here (Part II), the focus is on GMCR IIs analysis and output interpretation subsystems. Specifically, this paper describes the powerful and efficient analysis engine contained in GMCR II, its informative output presentation and interpretation facilities, and a number of follow-up analyses. Furthermore, an illustrative case study is used to demonstrate how GMCR II can be conveniently applied in practice.     

Field Static Load Test on Kao-Ping-Hsi Cable-Stayed Bridge

Field load testing is an effective method for understanding the behavior and fundamental characteristics of a cable-stayed bridge. This paper presents the results of field static load tests on the Kao-Ping-Hsi cable-stayed bridge, the longest cable-stayed bridge in Taiwan, before it was open to traffic. A total of 40 loading cases, including the unit and distributed bending and torsion loading effects, were conducted to investigate the bridge behavior. The atmospheric temperature effect on the variations of the main girder deflections was also monitored. The results of static load testing include the main girder deflections, the flexural strains of the prestressed concrete girder, and the variations of the cable forces. A three-dimensional finite-element model was developed. The results show that the bridge under the planned load test conditions has linear superposition characteristics and the analytical model shows a very good agreement with the bridge responses. Further discussion of deflection and cable forces of the design specifications for a cable-stayed bridge is also presented.