On the design considerations of solid-state power amplifiers for satellite communications: A systems perspective

Conventional solid-state power amplifier (SSPA) design approach isolates radio frequency (RF) design from communication theory. In this paper, a unified SSPA design approach is proposed, which optimizes SSPA parameters (bias voltage and input RF signal power) to minimize total DC power consumption while satisfying received SNR constraint specified by the link budget. The effect of SSPA nonlinearity is quantified by the error vector magnitude measured at its output and the corresponding received SNR degradation is analyzed. Using the quantitative metrics for received SNR, it is possible to evaluate highly nonlinear SSPA classes such as Class-B or deep-Class AB, which are normally not considered in conventional SSPA design approach to be used in satellite communication applications.     

In Situ Electrical Network Activation and Deactivation in Short Carbon Fiber Composites via 3D Printing

Prior studies on carbon-filler based, conductive polymer composites have mainly investigated how conductive filler morphology and concentration can tailor a material's electrical conductivity and overlooks the effects of filler alignment due to the difficulty to control and quickly quantify the filler alignment. Here, direct ink write 3D printing's unique ability is utilized to control carbon fiber alignment with a single process parameter, velocity ratio, to instantaneously activate or deactivate the electrical network in composites. Maximum electrical conductivity is achieved by randomly aligning carbon fibers that enhances the chance of direct fiber-to-fiber contact and, thus, activating the electrical network. However, aligning the fibers by increasing the velocity ratio disrupts the electrical network by minimizing fiber-to-fiber contact that resulted in a drastic decrease in electrical conductivity by as much as five orders of magnitude in both short and long carbon fiber composites. With this study, this study demonstrates that electrically conductive or insulative composites can be fabricated sequentially with a single ink. This novel ability to instantaneously control the electrical conductivity of carbon fiber reinforced composites allow to directly embed conductive pathways into designs to 3D print multifunctional composites that are capable of localized heating and self-sensing.     

Modelling of residual stresses in the shot peened material C-1020 by artificial neural network

This study consists of two cases: (i) The experimental analysis: Shot peening is a method to improve the resistance of metal pieces to fatigue by creating regions of residual stress. In this study, the residual stresses induced in steel specimen type C-1020 by applying various strengths of shot peening, are investigated using the electrochemical layer removal method. The best result is obtained using 0.26 mm A peening strength and the stress encountered in the shot peened material is ?276 MPa, while the maximum residual stress obtained is ?363 MPa at a peening strength of 0.43 mm A. (ii) The mathematical modelling analysis: The use of ANN has been proposed to determine the residual stresses based on various strengths of shot peening using results of experimental analysis. The back-propagation learning algorithm with two different variants and logistic sigmoid transfer function were used in the network. In order to train the neural network, limited experimental measurements were used as training and test data. The best fitting training data set was obtained with four neurons in the hidden layer, which made it possible to predict residual stress with accuracy at least as good as that of the experimental error, over the whole experimental range. After training, it was found the R² values are 0.996112 and 0.99896 for annealed before peening and shot peened only, respectively. Similarly, these values for testing data are 0.995858 and 0.999143, respectively. As seen from the results of mathematical modelling, the calculated residual stresses are obviously within acceptable uncertainties.     

Discrimination of quarry blasts and earthquakes in the vicinity of Istanbul using soft computing techniques

The purpose of this article is to demonstrate the use of feedforward neural networks (FFNNs), adaptive neural fuzzy inference systems (ANFIS), and probabilistic neural networks (PNNs) to discriminate between earthquakes and quarry blasts in Istanbul and vicinity (the Marmara region). The tectonically active Marmara region is affected by the Thrace-Eski?ehir fault zone and especially the North Anatolian fault zone (NAFZ). Local MARNET stations, which were established in 1976 and are operated by the Kandilli Observatory and Earthquake Research Institute (KOERI), record not only earthquakes that occur in the region, but also quarry blasts. There are a few quarry-blasting areas in the Gaziosmanpa?a, Çatalca, Ömerli, and Hereke regions. Analytical methods were applied to a set of 175 seismic events (2001-2004) recorded by the stations of the local seismic network (ISK, HRT, and CTT stations) operated by the KOERI National Earthquake Monitoring Center (NEMC). Out of a total of 175 records, 148 are related to quarry blasts and 27 to earthquakes. The data sets were divided into training and testing sets for each region. In all the models developed, the input vectors consist of the peak amplitude ratio (S/P ratio) and the complexity value, and the output is a determination of either earthquake or quarry blast. The success of the developed models on regional test data varies between 97.67% and 100%.     

Comparison on efficiency factors of F and C types of fly ashes

Fly ashes are obtained from thermal power plants and they are pozzolanic materials, which can act as partial replacement material for both portland cement and fine aggregate. With their economical advantages and potential for improving fresh and hardened concrete performance, they have some benefits for using in concrete industry. In this study, the objective was to find the efficiency factors of Turkish C and F-type fly ashes and to compare their properties. Three different cement dosages were used (260, 320, 400 kg/m³), two different ratios (10% and 17%) of cement reduced from the control concretes and three different ratios (depending on cement reduction ratio) of fly ash were added into the mixtures. At the ages of 28 and 90 days, compressive strength, modulus of elasticity and ultrasound velocity tests were carried out. From the compressive strength results, the k efficiency factors of C and F-type fly ashes were obtained. As a result, it is seen that efficiency factors of the concrete produced by the replacement of F and C type fly ashes with cement increase with the increase in cement dosage and concrete age.     

Zinc Oxide Nanowire Decorated Single‐Use Electrodes for Electrochemical DNA Detection

The surfaces of pencil graphite electrodes (PGEs) were decorated with zinc oxide nanowires (ZnO NWs) for the electrochemical detection of nucleic acids. ZnO NWs were synthesized through simple hydrothermal method. PGEs decorated with ZnO NWs (ZnO NW/PGEs) were electrochemically characterized through cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) following morphological characterization through transmission (TEM) and scanning electron microscopy (SEM). Enhanced sensor response obtained using ZnO NW/PGEs contrary to the bare PGE (control) samples. Our preliminary results simply reveal the potential of combining ZnO NWs with disposable sensor technology for the electrochemical detection of DNA.     

The interplay between leadership and organizational culture in the Turkish construction sector

Organizational culture and leadership are purported to be deeply integrated and intertwined within an organization. Although there is a substantial amount of research demonstrating the importance of the interplay of culture and leadership, there exist few empirical examinations of the nature of this link. To examine this link, based on Cameron and Quinn's Organizational Culture Assessment Instrument and Hofstede's Values Survey Module, a questionnaire survey was conducted. The sample consists of 499 managerial personnel out of 107 contracting firms. With the aim of achieving a better understanding of how leadership style is influenced by organizational culture, Multinomial Logistic Regression was used. The findings demonstrate that managers in the contracting companies with different cultural characteristics tend to adopt different leadership styles to lead their employees to succeed in their business. Information contained in this paper will feed into country-specific understanding of leadership and organizational culture within the construction industry.     

Modelling the impact of land-cover change on potential soil loss in the Taita Hills,Kenya, between 1987 and 2003 using remote-sensing and geospatial data

In sub-Saharan Africa, natural vegetation is being transformed into agricultural lands at a fast rate, endangering ecosystem services and increasing soil-loss potential, which may trigger land degradation. For the Taita Hills study area in Kenya, multi-temporal land-cover models of 1987, 1999 and 2003, derived from Satellite Pour l'Observation de la Terre (SPOT) imagery using a multi-scale segmentation/object relationship modelling (MSS/ORM) methodology and a rainfall layer, a digital elevation model (DEM) and a digital soil map were applied to model potential soil loss. Population growth in the area has led to a shortage of agricultural land and movement of people to the lowlands, evidenced by a 39% (9.3 km²) increase in croplands from 30% to 41% of the study area during the research time frame. Expansion took place mostly in surrounding foothills and lowlands, at the expense of natural shrubland and grassland, but also occurred in the hills. Universal soil-loss equation (USLE) model results showed a 60% (4 km²) increase in the area of very high potential soil loss, from 7% of the study area in 1987 to 12% in 2003, due mainly to very high soil-loss potential in croplands. Whilst the area of croplands as a whole increased, the relative proportion of very high soil-loss potential in croplands remained 20%, both in 1987 and in 2003, indicating that newly cleared agricultural lands with vulnerable soils are the most at-risk areas.     

Packet Reservation Window Multiple Access for Microcellular Voice/Data Transmission

We propose a new packet reservation multiple access (PRMA) scheme for the joint transmission of voice and data traffics in a microcellular medium. The collision resolution protocol within the system is based on a modification of the window random access algorithm, which has superior properties compared to the conventional slotted Aloha. The proposed algorithm, which we call packet reservation window multiple access (PRWMA), works in distinct modes for voice and data without prioritization, and the user performs slightly different operations depending on the information type. Simulation results show that PRWMA outperforms PRMA by a significant margin in terms of voice user capacity.     

All Solution‐Based Fabrication of Copper Oxide Thin Film/Cobalt‐Doped Zinc Oxide Nanowire Heterojunctions

Versatile and intriguing solution‐based processes are utilized to synthesize nanostructured materials for device applications to reduce material production and device fabrication costs. This study presents results on the fabrication and characterization of copper oxide (CuO) coated cobalt‐doped zinc oxide nanowires (Co‐doped ZnO NWs)‐based heterojunction diodes prepared by a two‐step synthesis route through combined hydrothermal growth and sol–gel spin coating. Highly dense, well‐ordered, undoped, and Co‐doped ZnO NWs were successfully grown by hydrothermal method. Complementary CuO thin films were synthesized by sol–gel method and subsequently coated onto both undoped and Co‐doped ZnO NWs through spin‐coating technique. Enhanced diode properties with a rectification ratio of 10³ at ±2 V and an ideality factor of n = 2.4 (in dark) were obtained for Co‐doped ZnO NWs‐based heterojunction diodes. The obtained results demonstrated that the investigated heterojunction diode structure fabricated by facile and cost‐effective solution‐based processes can be a promising candidate for the next generation optoelectronic devices.