Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

Assessing the potential of renewable energy sources in Turkey

To meet Turkey’s growing energy demand, the installed electric power capacity of 27.8 GW in 2001 has to be doubled by 2010 and increased fourfold by 2020. The difference between Turkey’s total primary energy supply (TPES) of from its own sources and total final consumption (TFC) is projected grow from 1 quad (1.06–2.06) in 1999 to 5.71 quads (2.79–8.5) in 2020 (1 QUAD=293.071 TWh). Turkey’s limited amount of fossil fuels has a present average ratio of proved reserves of 97.38 quads to production rate of 3.2 quads yr⁻¹ of about 30 years. Turkey’s reliance on fossil fuel-based energy systems to meet the growing demand is most likely to exacerbate the issues of energy insecurity, national environmental degradation, and global climate change in increasing proportions. Economically-feasible renewable energy potential in Turkey is estimated at a total of ca. 1.69 quads yr⁻¹ (495.4 TWh yr⁻¹) with the potential for 0.67 quads yr⁻¹ (196.7 TWh yr⁻¹) of biomass energy, 0.42 quads yr⁻¹ (124 TWh yr⁻¹) of hydropower, 0.35 quads yr⁻¹ (102.3 TWh yr⁻¹) of solar energy, 0.17 quads yr⁻¹ (50 TWh yr⁻¹) of wind energy, and 0.08 quads yr⁻¹ (22.4 TWh yr⁻¹) of geothermal energy. Pursuit and implementation of sustainability-based energy policy could provide about 90 and 35% of Turkey’s total energy supply and consumption projected in 2010, respectively. Utilization of renewable energy technologies for electricity generation would necessitate about 23.2 Mha (29.8%) of Turkey’s land resources.     

The role of diagnostic laparoscopy in treatment of penetrating injuries of the lower thoracic wall and anterior abdominal wall

Penetrating injuries of the lower thoracic wall and anterior abdominal wall cause difficulties in the decision for laparotomy. For gunshot wounds laparotomy without further investigations is in most cases justified, but in other penetrating traumata one should use every diagnostic modality to prevent unacceptably high negative laparotomy rates. We performed diagnostic laparoscopy (DL) on 39 patients with penetrating injuries of the anterior abdominal wall and/or lower thoracic wall. Of these 39 patients, 25 had negative and 14 positive results. We had only one false-negative finding. No false-positive result occurred. We think that DL is a very reliable diagnostic tool which requires a relatively high technology.     

Frequency and Voltage Dependence of Dielectric Loss of MgB2 Composites at Different Temperatures

The dielectric loss (ε″) properties of MgB₂ composites were investigated by using the conductance–voltage (G/w–V) measurements in the wide frequency and applied bias voltage range at four different temperature levels. Experimental results show that both G/w and ε″ are found strong functions of frequency and applied bias voltage for each temperature level. These changes in G/w and ε″ are considerably high especially at low frequencies and temperatures. The values of ε″ decrease exponentially with increasing frequency until 100 kHz and then become almost constant. Such behavior of G/w and ε″ shows that interfacial polarization is more effective especially at low frequencies. In addition, the current–voltage (I–V) characteristics were also evaluated for 100, 200, and 300 K, and the I–V curves for each temperature show linear behavior. Results indicate that the G/w–V measurements may be a useful tool to characterize the dielectric properties and conductivity of MgB₂.     

Characterization of closed-loop measurement accuracy in precision CNC milling

This study investigates the closed-loop measurement error in computer numerical controlled (CNC) milling as they relate to the different inspection techniques. The on-line inspection of machining accuracy using a spindle probe has an inherent shortcoming because the same machine-produced parts are used for inspection. In order to use the spindle probe measurement as a means of correcting deviations in machining, the magnitude of measurement errors needs to be quantified. The empirical verification was made by conducting three sets of cutting experiments, followed by a design of experiment with three levels and three factors on a state-of-the-art CNC machining center. Three different material types and parameter settings were selected to simulate a diverse cutting condition. During the cutting, the cutting force and spindle vibration sensor signals were collected and a tool wear was recorded using a computer vision system. The bore tolerance was gauged by a spindle probe as well as a coordinate-measuring machine. The difference between the two measurements was defined as a closed-loop measurement error and the subsequent analysis was performed to determine the significant factors affecting the errors. The analysis results showed the potential of improving production efficiency and improved part quality.     

Use of levodopa to relieve pain from painful symmetrical diabetic polyneuropathy

Levodopa has been used to treat some painful conditions and found to be effective in neuropathic pain due to herpes zoster in a double-blind study. From our anecdotal observations about the efficacy of levodopa on diabetic neuropathic pain, we designed a double-blind placebo-controlled study to test levodopa in painful diabetic neuropathy. Twenty-five out-patients with painful symmetrical diabetic polyneuropathy were admitted to the study. Fourteen patients were given 100 mg levodopa plus 25 mg benserazide to be taken three times per day for 28 days. Eleven patients were given identical placebo capsules. A blinded neurologist evaluated the patients clinically and performed Visual Analogue Scale (VAS) measurement every week from day 0 to day 28. The results seemed promising and levodopa may be a choice for the control of pain in neuropathy for which we do not have many alternative treatments.     

Internet protocol header compression, robust header compression, and their applicability in the global information grid

IPv6 extends capabilities of legacy IPv4 networks. The advantages of IPv6, however, come at the cost of increased operational overhead. As government networks providing services to the global information grid (GIG) migrate toward an IPv6-based infrastructure, the implications of an expanded packet header must be analyzed. This article describes two IPv6 applicable header compression schemes developed by the IETF, and how networks across the GIG infrastructure can adopt them in an effort to reduce IPv6 expanded overhead requirements.