Creep and Stress Rupture Behavior of an Advanced Silicon Nitride: Part I, Experimental Observations

Cylindrical buttuohead specimens of an advanced silicon nitride were tested in uniaxial tension at temperatures between 1422 and 1673 K. In the range 1477 to 1673 K, creep deformation was reliably measured using high-temperature contact probe extensometry. Extensive scanning and transmission electron microscopy has revealed the formation of lenticular cavities at two-grain junctions at all temperatures (1422–1673 K) and extensive triple-junction cavitation occurring at the higher temperatures (1644–1673 K). Cavitation is believed to be part of the net creep process. The stress rupture data show stratification of the Monkman–Grant lines with respect to temperature. Failure strain increased with increase in rupture time or temperature, or decrease in stress. Fractography showed that final failure occurred by subcritical crack growth in all specimens.     

Processing, Microstructure, and Wear Behavior of Silicon Nitride Hot-Pressed with Alumina and Yttria

Commercial silicon nitride powder with A1₂O₃ and Y₂O₃ additives was hot-pressed to complete density. The resulting microstructure contained elongated grains with no trace of remaining α-Si₃N₄. The aspect ratio of the elongated grains increased with increasing soak time at a fixed hot-pressing temperature. X-ray diffraction analysis showed that the crystalline phase in the hot-pressed samples was β-sialon (Si_6−zAl_zO_zN_8−z) with z values that increased with soak time. The fracture strength and fracture toughness of the samples increased as the aspect ratio of the grains increased. The Vickers hardness decreased slightly as the soak time was increased, which was attributed to a grain size effect. Wear tests of silicon nitride against silicon nitride were conducted on a reciprocating pin-on-disk apparatus with paraffin oil as a lubricant. Correlation studies of wear with microstructure and mechanical properties were performed. The wear rate increased rapidly with increasing soak time in spite of the increased strength and toughness. This was attributed to increased third-body wear caused by pullout of pieces from the wear surface. The pullout mechanism was not conclusively identified. However, TEM examination showed clear evidence of dislocation motion under the wear scar. Grain boundary microstresses caused by the anisotropic thermal expansion and elastic properties of the elongated grains may have contributed to the observed pullout.     

Reverse cyclic fatigue of a hot isostatically pressed silicon nitride at 1370 °C

The uniaxial, reverse cyclic fatigue performance of a commercially available hot isostatically pressed silicon nitride was examined at 1370 °C in air and with a 1 Hz sinusoidal waveform using button-head tensile specimens. Specimens did not fail in less than 10⁶ cycles when the applied stress amplitude was less than 280 MPa. Slow crack growth occurred at stress amplitudes 280 MPa and failure always occurred during the tensile stroke of the waveform. Multi-grain junction cavities resulted (i.e., the accumulation of net tensile creep strain) as a consequence of the reverse cyclic loading even though the specimens endured half their life under tensile stresses and the other half under compressive stresses. The presence of multi-grain junction cavities was a consequence of the stress exponent of tensile creep strain being greater than the stress exponent of compressive creep strain. Lastly, it was observed that the static creep resistance of this material improved when it was first subjected to reverse cyclic loading at 1370°C for at least 10⁶ cycles at 1 Hz. Silicon nitride grain coarsening (which was a consequence of the completion of the to silicon nitride solution/reprecipitation process that occurred during the history of the reverse cyclic loading) lessened the capacity for grain boundary sliding resulting in an improved static creep resistance.     

Chemical reactivity of mineral aggregates in aqueous solution: relationship with bitumen emulsion breaking

This paper reports a study on chemical reactivity of gneiss, diorite and limestone aggregates in aqueous solution. The originality of this study is that it extended to very short times (less than 1440 min). Rise in pH tests was implemented and dissolution kinetics was analysed. The results showed that calcium was the major element released by the aggregates. It has also been found that dissolution had an influence on the final morphology of aggregates. Polyamine emulsifier adsorption onto aggregates has been assessed using electrophoresis. Finally, the rise in pH and electrophoretic tests were compared to the breaking test traditionally performed to characterise bitumen emulsions. It was found that breaking values were controlled by both the surface area and the surface charge of the particles. Results may be correlated to polyamine adsorption on aggregates. Adsorption seemed to be efficient for gneiss and diorite: at pH 2, their charge turned from slightly negative to highly positive. At this pH value, limestone particles were dissolved and polyamine adsorption must be less efficient than with gneiss and diorite, for which the emulsion breaking was facilitated by the high attraction of particles for the emulsifier, due to their negative surface charge.     

Dimensional changes and creep of silica core ceramics used in investment casting of superalloys

Dimensional changes and creep deformation of a silica/zircon (74%/24%, respectively) and a high silica (93% silica and 3% zircon) ceramic were characterized and compared. All specimens were tested with a thermal profile that consisted of a 300°C/h heating rate to 1475 or 1525°C, followed by a one-hour isothermal hold (where each specimen was compressively crept under a static stress of 2.07, 4.14, or 6.21 MPa). The specimens were cooled at a rate of 900°C/h under stress. Dimensional changes were interpreted from apparent thermal expansion behavior during heating as well as before-and-after dimensional measurements. The silica/zircon ceramic generally exhibited less total contraction than the high silica ceramic for a specific test condition even though it crept faster at all stresses and temperatures during the one-hour isothermal/isostress segment. This indicates that the total contraction for both was dominated by reinitiated sintering and subsequent cristobalite formation that occurred during the heating segment. Minimum creep rate during the one-hour isothermal/isostress segment was examined as a function of stress and temperature for both ceramics using a power-law creep model. Creep-rate stress exponents (n) and activation energies (Q) were equivalent (within 95% confidence) for both ceramics showing that their different contents of zircon (3 vs. 24%) did not affect them. Lastly, n 1.3–1.4 and Q 170 kJ/mol indicate that diffusion-assisted crystallization of cristobalite, combined with power-law sintering owing to the high concentration of porosity (28–30%) was likely the rate-limiting mechanism in the creep deformation for both ceramics.     

ISO learning approximates a solution to the inverse-controller problem in an unsupervised behavioral paradigm

In "Isotropic Sequence Order Learning" (pp. 831-864 in this issue), we introduced a novel algorithm for temporal sequence learning (ISO learning). Here, we embed this algorithm into a formal nonevaluating (teacher free) environment, which establishes a sensor-motor feedback. The system is initially guided by a fixed reflex reaction, which has the objective disadvantage that it can react only after a disturbance has occurred. ISO learning eliminates this disadvantage by replacing the reflex-loop reactions with earlier anticipatory actions. In this article, we analytically demonstrate that this process can be understood in terms of control theory, showing that the system learns the inverse controller of its own reflex. Thereby, this system is able to learn a simple form of feedforward motor control.     

Biomarkers for cardiovascular risk assessment in autoimmune diseases

Autoimmune diseases, such as antiphospholipid syndrome, systemic lupus erythematosus, and rheumatoid arthritis, are characterized by a high prevalence of cardiovascular (CV) disease (CVD), which constitutes the leading causes of morbidity and mortality among such patients. Although such effects are partly explained by a higher prevalence of traditional CV risk factors, many studies indicate that such factors do not fully explain the enhanced CV risk in these patients. In addition, risk stratification algorithms based upon traditional CV risk factors are not as predictive in autoimmune diseases as in the general population. For these reasons, the timely and accurate assessment of CV risk in these high-risk populations still remains an unmet clinical need. An enhanced contribution of different inflammatory components of the immune response, as well as autoimmune elements (e.g. autoantibodies, autoantigens, and cellular response), has been proposed to underlie the incremental CV risk observed in these populations. Recent advances in proteomic tools have contributed to the discovery of proteins involved in CVDs, including some that may be suitable to be used as biological markers. In this review we summarize the main markers in the field of CVDs associated with autoimmunity, as well as the recent advances in proteomic technology and their application for biomarker discovery in autoimmune disease.     

Effect of oxidizing and coal-slag environments upon the time-dependent strength behaviour of a sintered SiC

The time-dependent variations in the high-temperature mechanical properties of a sintered SiC were investigated. The strength of C-ring specimens was determined as a function of temperature and applied stress in oxidizing atmospheres, and the results indicated that both crackblunting and crack-growth processes were operative when modest stress levels were applied. These results were consistent with the concept of a stress-intensity threshold. In the slag environment, localized reactions between the slag and SiC led to the formation of large surface pits which promoted a time-dependent drop in strength.     

The role of the SnO2 interphase in an alumina/glass composite: a fractographic study

The role of tin dioxide (SnO₂) interphase for the alumina/glass composite system was investigated using fractography. Alumina (Al₂O₃) and glass form a strong chemical bond which is undesirable for toughness in a ceramic matrix composite. SnO₂ interphase was incorporated to prevent this strong bond between alumina and glass. SnO₂ was deposited on Al₂O₃ substrates via chemical vapour deposition and bonded with glass. The role of the interphase was then studied by characterizing the fracture surfaces of the bend test and special composite disc samples loaded in diametral compression. Bend tests results showed that the SnO₂ interphase and/or the SnO₂/Al₂O₃ interface acted as a plane of weakness. Secondary cracking at 90° to the major crack direction was observed along this plane of weakness, which appears to be in accord with the Cook and Gordon model. Crack deflection and secondary cracking were also observed in the SnO₂ region of the compression samples. These results indicate the suitability of SnO₂ interphase for the alumina/glass composite system.     

Imitation milks from Cicer arietinum (L.), Vigna unguiculata (L.) walpers and Vigna radiata (L.) wilczek and other legumes

Vegetable milks were prepared in the laboratory from mung bean [Vigna radiata (L.) Wilczek], cowpea [Vigna unguiculata (L.) Walpers] and chick-pea [Cicer arietinum (L.)] by homogenisation of a filtered aqueous extract of the ground legume with soya bean oil. Emulsions stable to pasteurisation were made from the first two. Pigeon pea [Cajanus cajan (L.)] and black gram [Vigna mungo (L.) Hepper)] were found to be unsuitable as bases for milks prepared by simple processing. The nitrogen, oil, sugar and ash contents of the first three legumes, and of milks prepared from them, were determined. Imitation milks are intended to resemble animal milks nutritionally, and whilst the contents of potassium and phosphorus were acceptable, these vegetable milks were low in sodium, calcium and zinc. The trypsin inhibitory activity, whilst low in comparison with soya milk, was partially stable to pasteurisation. The amino acid composition indicated that it would be desirable to complement legume proteins with cereal proteins to prepare vegetable milks.