Three ways to implement interfacial techniques: application tomeasurements of chromatic dispersion, birefringence, and nonlinearsusceptibilities

Depending on the spectal width of the source illuminating an interferometer, measurement procedures can utilize either the whole interferogram, or only the fringe envelope, or only the fringe quick oscillations. With an ultraband spectrum source, a simplified adaptation of the methods of Fourier transform spectroscopy yields the variations of the test-fiber propagation constant over the whole wavelength-interval of the source. Chromatic dispersion can then be computed from a single interferogram. With narrower spectrum sources, only the fringe envelopes are utilized and yield measurements of mode delay, with application to chromatic and polarization mode dispersion. In this case, however, interferograms at several wavelengths are necessary. With even narrower spectrum sources, the fringe quick oscillations provide measurements of phase shifts, related to changes in the mode propagation constant, when outside perturbations are applied to the test fiber. A direct method for measuring the third-order nonlinear susceptibilities is discussed. In this case the outside perturbation is an intense pump laser field     

Wide- and narrow-band bandpass coplanar filters in the W-frequency band

This paper deals with the design of passive coplanar devices in the W-frequency band. As long as coplanar transmission lines are correctly dimensioned, analytical models based on quasi-TEM approximation can be used. Such models are associated with a correct definition of the reference planes at the junctions and employed for junction discontinuities, T- and cross-junctions. In order to validate these assertions, simulated and experimental data on classical quarter-wavelength shunt-stub filters are first presented. Then the design of traditional coupled-line filters is examined. The problems in terms of insertion loss associated with these kinds of narrow-band applications are discussed here. Minimization of insertion losses requires increasing the width of the strips. Consequently, the design becomes complex and modeling using transmission-line models less accurate. Nevertheless, as an optimization procedure is needed to tune the filter theoretically, such a very fast design method is necessary. Simulated and experimental results in the range 500 MHz to 110 GHz are compared throughout the paper.     

High-frequency performance of submicrometer channel-length siliconMOSFETs

Polycide-gate silicon n-channel MOSFETs were fabricated on the basis of a standard 0.5-μm MOS technology and measured over the 1.5-26.5-GHz frequency range, in order to investigate the effects of channel-length reduction on device behavior at high frequency. Excellent microwave performances were obtained with a maximum operating frequency (f_max) and a unity-current-gain frequency f _t near 20 GHz for 0.5-μm-gate-length NMOS devices. An equivalent circuit for a MOSFET with its parasitic elements was extracted from measured S-parameter data. The influence of gate resistance, gate-to-drain overlap capacitance, substrate conductivity, and the transit-time effect between the source and drain on microwave characteristics was analyzed     

A new empirical nonlinear model for sub-250 nm channel MOSFET

An empirical nonlinear model for sub-250 nm channel length MOSFET is presented which is useful for large signal RF circuit simulation. Our model is made of both analytical drain current and gate charge formulations. The drain current expression is continuous and infinitely derivable, and charge conservation is taken into account, as the capacitances derive from a single charge expression. The model's parameters are first extracted, prior the model's implementation into a circuit simulator. It is validated through dc, ac, and RF large signal measurements compared to the simulation.     

Polymer aqueous solutions as quenching media. II. Ethylene oxide–propylene oxide copolymers

The cooling power of aqueous solutions of ethylene oxide-propylene oxide copolymers are studied with a silver standard sample by using two apparatuses quench with injection and quench with agitation. For temperature T>400°C, the viscosity plays the predominant role; for T<400°C, the cooling is controlled by the polymer precipitation and the cooling rate decreases by lowering the cloud point of the polymer solution. This work demonstrates the possibility of adjusting the cooling curves by taking into account the thermodynamical properties of the polymer.     

The correlation between the thermoelectric properties and stoichiometry in the boron carbide phase B4C-B10.5C

Electrical conductivity, thermoelectrical power and thermal conductivity measurements on boron carbide samples show that the electrical conductivity follows the small polaron hopping theory and that thermal conductivity occurs by phonon diffusion. The evolution of these properties with carbon content illustrates the particular role played by the 13.3 at% C compound in the phase homogeneity range B_10.5C to B₄C. The value of the figure of merit (0.85×10^–3 K at 1250 K) proves that this particular boron carbide compound could be a very interesting candidate material for high-temperature thermoelectrical conversion.     

A single phase model of mechanisms effecting miscible surfactant oil recovery

The concept of volume averaging is used to theoretically study the mechanisms of mass dispersion, adsorption, and dead-space volume. These mechanisms are important to the understanding of miscible surfactant flooding. After simpiffication based on order-of-magnitude scaling, a linear core model is solved using state variable finite-difference techniques. Mass dispersion and adsorption are shown to be important model parameters while dead-space volume is a rather insensitive model parameter.     

冠带层新平台技术

子午线轮胎出现不久，就采用钢丝带束层代替了纤维带束层，这对于实现子午线轮胎提高使用寿命和改善操纵性能的潜能是必要的。     

Visiting pebbles on rectangular grids: coordinating multiple robots in mobile fulfilment systems

Intelligent Service Robotics - Multi-robot path finding and coordination is one of the key performance-affecting subsystems of the overall robotic order fulfilment process for use in warehouse...