Performance of compression/absorption hybrid refrigeration cycle with propane/mineral oil combination

This paper discusses the feasibility of a vapor compression/absorption hybrid refrigeration cycle for energy saving and utilization of waste heat. The cycle employs propane as a natural refrigerant and a refrigeration oil as an absorbent. A prototype of the cycle is constructed, in which a compressor and an absorption unit are combined in series. The performance of the cycle is examined both theoretically and experimentally. Although the solubility of the propane with the oil is not enough as a working pair in the absorption unit, the theoretical calculation shows that the hybrid cycle has a potential to achieve a higher performance in comparison with a simple vapor compression cycle by using the waste heat. In the experiment, the prototype cycle is operated successfully and it is found that an improvement of an absorber is necessary to achieve the good performance close to the theoretical one. The application of an AHE (absorber heat exchanger) can reduce the heat input to a generator. Further examinations on some other combinations of refrigerant/refrigeration oil and additives are desirable.     

FPGA-Based Decentralized Control of Arrayed MEMS for Microrobotic Application

In this paper, the authors have developed and implemented a decentralized decision-making strategy using field-programmable gate array (FPGA) technology as a prototype for an integrated controller of a microelectromechanical systems (MEMS) array for air-flow planar micromanipulation. The MEMS array was proposed to be integrated in a hybrid multichip module containing the FPGA-based controller. Algorithms and architectures, used for the decentralized control implementation and the hardware resource optimization, are described. A charge-coupled device camera was used to make each MEMS like an autonomous system when the distributed MEMS chip was tested. Finally, under air-flow condition, the FPGA-based decentralized control system successfully performed an object manipulation.     

Benign fibroosseous lesions involving the skull base, paranasal sinuses, and nasal cavity. Report of two cases

We report a case of a basilar artery migraine in a 17-year-old boy with transient CT and MR abnormalities after each of two migraine episodes. A repeat MR study 6 months after the last event showed complete resolution of the lesion. Transient abnormalities on brain images similar to those shown in our case have been reported in patients with migraine and other neurologic conditions and are most likely related to cerebral vasogenic edema.     

On a compound redundant system with the particular switching devices

This paper considers a standby-redundant system consisting of 2 systems, in which one is main and the other is its standby-redundant system. These systems also consist of 2 subsystems connected in series, in which each one is composed of several identical units connected in parallel.A feature of this system is that the system has 2 switching devices connecting subsystems, in addition to one connecting main and standby systems, in order to utilize surviving units as many as possible. In this consideration it is assumed that all the units are not repairable.We shall obtain the system reliability and the mean time to system failure, and examine numerically the effects of this model to the usual one without particular switching devices.     

Shear properties of metal-free wooden load-bearing walls using plywood jointed with a combination of adhesive tape and wood dowels

In this study, the potential of wood-only (metal-free) load-bearing walls was proposed and tested based on the idea of using the same type of material throughout wherever possible while improving basic properties such as strength, sound insulation, and heat insulation. Specifically, a technique was tested of combining pressure sensitive adhesive tape and wood dowels in place of nails for load-bearing structures with panel reinforcement represented by wood-frame construction. For this paper, its strength was evaluated by conducting in-plane shear tests, which revealed that the initial rigidity and maximum load of the proposed test specimens were greater than that of specimens using nails for jointing. However, the shear load factor, which is calculated based on some strength parameters and which forms the foundation of housing strength design, was slightly lower than that of the nail-jointed specimen. This was because there was a large decline in post-collapse resistance and a lower calculated absorbed energy caused by brittleness. The early detachment of panels was also revealed as a problem in the tests.     

Reliability consideration on a compound redundant system with repair

This paper considers a standby-redundant system consisting of 2 systems, in which one is main and the other is its standby-redundant system. These systems also consist of 2 subsystems connected in series.A feature of this system is that the system has 2 switching devices connecting subsystems, in addition to one connecting main and standby systems, in order to utilize surviving subsystem. In this consideration it is assumed that all the units are repairable.We shall obtain the system reliability, the mean time to system failure, the steady state availability, and examine numerically the effects of this model to the usual one without particular switching devices.     

Growth of β-Ga2O3 nanocolumns crossing perpendicularly each other on MgO (1 0 0) surface

β-Ga₂O₃ nanocolumns straightened and crossed perpendicularly each other were deposited on MgO (1 0 0) substrate by vapor phase transport method. Growth of the nanocolumns was examined at steps of 1000, 1050, and 1200 °C in elevation of source-boat temperature. We have drawn out the substrate from deposition-tube at each source-boat temperatures of 1000, 1050, and 1200 °C. Scanning electron microscopy of the sample with source-boat temperature of 1200 °C demonstrated that the straightened and elongated nanocolumns are crossing perpendicularly each other. Typical lengths of the nanocolumns were in the range of several hundreds nanometers below 1050 °C, and those of 1200 °C were in the range of ten to fifteen hundreds nanometers. Diameters of the nanocolumns stayed in the range of few hundreds nanometers, notwithstanding variation of the source temperature. X-ray diffraction and transmission electron microscopy with energy dispersive X-ray spectroscopy revealed that the nanocolumns are monoclinic β-Ga₂O₃ crystal, and the (4 0 0) plane of β-Ga₂O₃ nanocolumns is parallel to the (1 0 0) plane of MgO substrate.     

Characterization of mixing performance in a microreactor and its application to the synthesis of porous coordination polymer particles

Here we quantitatively evaluated the mixing performance of a tailor-made microreactor with central-collision type through the iodide/iodate chemical test reaction, and applied the microreactor to the synthesis of zeolitic imidazolate framework-8 (ZIF-8), which is a subclass of porous coordination polymers (PCPs) or metal organic frameworks (MOFs). The chemical test reaction demonstrated excellent mixing performance of the microreactor with a characteristic mixing time shorter than 1 ms, which is approximately 100 times faster than those of a batch reactor and a millimeter-sized Y-shaped mixer. Taking advantage of the rapid and uniform mixing, the microreactor successfully produced ZIF-8 particles with high reproducibility by simply mixing aqueous solutions of zinc nitrate and 2-methylimidazole. The synthesis at room temperature resulted in ZIF-8 particles with chamfered cube shape, while a lower temperature of 5 °C produced raspberry-type spherical particles. We confirmed that prepared ZIF-8 particles have BET surface area of ～1500 m²/g and exhibit the gate adsorption behavior caused by the structural transition of the ZIF-8 framework.