Hot carrier analysis in low-temperature poly-Si thin-film transistors using pico-second time-resolved emission microscope

We have analyzed degradation of N-channel thin-film-transistor (TFT) under dynamic stress using a pico-second time-resolved emission microscope. We have successfully detected emission at pulse fall edge for the first time. Emission intensity increased with the decrease of pulse fall time. As the degradation depended on the pulse fall time, this dependence clearly illustrates that hot electrons are the dominant cause of the degradation under dynamic stress. Based on these dependences, we proposed a model considering electron traps in the poly-Si.     

Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

An over 2200-km coherent transmission experiment at 2.5 Gb/s usingerbium-doped-fiber in-line amplifiers

A 2223 km transmission distance was achieved with a 2.5-Gb/s heterodyne detection system that used erbium-doped-fiber in-line amplifiers and dispersion-shifted single-mode fibers. Twenty-five amplifiers, placed at approximately 80-km intervals, offered a total gain of more than 440 dB. Receiver sensitivity was -42.0 dBm, with only a 4.2-dB penalty from the initial sensitivity achieved by the back-to-back configuration     

Free volume and permeabilities of O2 and H2 in Nafion membranes for polymer electrolyte fuel cells

The mechanism of gas permeation in Nafion membranes for polymer electrolyte fuel cells has been investigated from the viewpoint of free volume. Three different samples, a membrane with ionic exchange capacity (IEC) = 0.92 meq/g, and recast samples with IEC = 0.92 and 1.00 meq/g were used after drying. Free volume was quantified using the positron annihilation lifetime (PAL) technique and gas permeabilities were measured for O₂ and H₂ as functions of temperature and relative humidity. Good linear correlations between the logarithm of the permeabilities at different temperatures and reciprocal free volume indicate that gas permeation in dry Nafion is governed by the free volume. Nevertheless permeabilities are much smaller than the corresponding flexible chain polymer with a similar free volume size due to stiff chains of the perfluoroethylene backbone. In highly hydrated Nafion above 60% relative humidity, where the O₂ permeability varies oppositely to the free volume, gas permeation proved to be controlled by the gradual increase in overall flexibility of the Nafion–water system.     

A Generalized Technique for Register Counting and its Application to Cost-Optimal DSP Architecture Synthesis

In this paper we propose a generalized technique to count the required number of registers in a schedule which supports overlapped scheduling and can be applied to the case where a general digit-serial data format is used. This technique is integrated into an integer linear programming (ILP) model for time-constrained scheduling. In the ILP model, appropriate processors of certain data formats are chosen from a library of processors and data format converters are automatically inserted between processors of different data formats if necessary. Then the required number of registers for each data format is evaluated correctly by the proposed technique. Hence an optimal architecture for a given digital signal processing algorithm is synthesized where the cost of registers as well as the cost of processors and data format converters are minimized. It is shown that by including the cost of registers in the synthesis task as proposed in this paper leads to up to 12.8% savings in the total cost of the synthesized architecture when compared with synthesis performed without including the register cost in the total cost.     

Studies on sublimation of disperse dye out of dyed polymers. I. Rate of sublimation and amorphous transition points of poly(ethylene terephthalate)

Four samples of poly(ethylene terephthalate) film of various crystallinities and orientation were dyed with p-nitroaniline and disperse dyes. When these films were heated under a 2–3 × 10^?3 mm Hg vacuum at a specified temperature T, the dye sublimed out of the dyed specimen. The amount (M_t/M_∞) of sublimed dye is in linear proportion to the square root of the sublimation time, t^½, where M_t and M_∞ are the amounts of dye sublimed for times t and t = ∞. The diffusion coefficient D, calculated from the slope of the above plot, is independent of the dye concentration of the film. When log D is plotted against 1/T°K over the temperature range 320–520°K, the relation is composed of two to four intersecting lines with the slope decreasing with elevation of temperature and with the breaks at about 89°–98°, 122°–135°, 155° and 175°–176°C. These breaks are the amorphous transitions: the first is the glass transition temperature T_g, the second and the fourth are the amorphous transitions corresponding to the crystalline transition points, i.e., the cold crystallization temperature and the smectic–triclinic transition temperature. With some exceptions, these amorphous transitions are found also by dilatometry and electrical conductivity measurements. The apparent activation energy for diffusion decreases from about 100 kcal/mole for the glass state to 22–24 kcal/mole for the region above 180°C. The activation energy for each region changes slightly with the size of dye molecule and the crystallinity and orientation of the film.     

The effects of oxygen diffusion on the surface photooxidation of polystyrene

This paper further illustrates the applicability of multiple internal reflectance infrared spectroscopy to the analysis of near-surface photooxidation. The results are compared with transmission infrared spectra to evaluate compositional gradients resulting from photooxidation and the influence of oxygen diffusion. The sample was a solvent-cast film of atactic, narrow distribution polystyrene, M_w of 100,000, that had been drawn to a ratio of 3.0 at 110°C by solid state coextrusion. Irradiation of these thin films, ～25μm thickness, was performed on exposure to air at 35°C for periods of up to 6 h using a mercury source emitting at 254 nm. On photooxidation, a board peak appears at 3200–3500 cm^?1, attributable to hydroperoxide formation. The most dramatic increase in the infrared spectra is found for a carbonyl band at 1730 cm^?1. It appears to result from an aromatic acid group since it is shifted to 1660 cm^?1 on immersion of the oxidized polystyrene films in aqueous ammonium hydroxide. It is confirmed that the photooxidation of polystyrene occurs preferentially at the surface and that this reaction rate is greatly reduced in the drawn polystyrene film.     

Poly(p-tert-butoxycarbonyloxystyrene): a convenient precursor to p-hydroxystyrene resins

An efficient synthetic route to pure, high molecular weight poly(p-hydroxystyrene) is reported. The route involves synthesis of a new monomer, p-tert-butoxycarbonyloxystyrene, polymerization by radical initiation or by cationic initiation in liquid SO₂, followed by thermolysis or acidolysis of the tert-butoxycarbonyl protecting group. Porous, crosslinked resin beads containing the nucleophilic, phenol pendant group have been prepared in a similar fashion from the precursor terpolymer of p-tert-butoxycarbonyloxystyrene, styrene and divinylbenzene. The utility of this resin for solid-phase synthesis has been demonstrated.