A CMOS multichannel 10-Gb/s transceiver

We describe a CMOS multichannel transceiver that transmits and receives 10 Gb/s per channel over balanced copper media. The transceiver consists of two identical 10-Gb/s modules. Each module operates off a single 1.2-V supply and has a single 5-GHz phase-locked loop to supply a reference clock to two transmitter (Tx) channels and two receiver (Rx) channels. To track the input-signal phase, the Rx channel has a clock recovery unit (CRU), which uses a phase-interpolator-based timing generator and digital loop filter. The CRU can adjust the recovered clock phase with a resolution of 1.56 ps. Two sets of two-channel transceiver units were fabricated in 0.11-/spl mu/m CMOS on a single test chip. The transceiver unit size was 1.6 mm /spl times/ 2.6 mm. The Rx sensitivity was 120-mVp-p differential with a 70-ps phase margin for a common-mode voltage ranging from 0.6 to 1.0 V. The evaluated jitter tolerance curve met the OC-192 specification.     

影响掺矿渣的钢纤维砼强度的主要因素

研究结果表明 :水胶比、胶凝材料用量、钢纤维掺量、矿渣代水泥量对钢纤维砼强度影响显著。当矿渣取代水泥 10 %时 ,钢纤维砼强度最高。经试验选择出一个具有良好和易性和较高强度 (118MPa)的钢纤维砼配合比 ,为掺磨细矿渣的中含量超短异形钢纤维砼的设计和施工提供了试验依据     

Fault section detection system for 66 kV underground branchtransmission lines using optical magnetic field sensors

A fault section detection system that uses optical magnetic field sensors and instantly detects the section in which a ground fault occurred was developed for 66 kV underground multiterminal systems having Y-branch joint boxes. The optical magnetic field sensor, which is based on the Faraday effect in Bi-doped YIG ((BiYbGd)₃Fe₅O₁₂) having a large Verdet constant, detects cable conductor currents of 0 to 2000 A with high precision with the use of a laminated magnetic ring core of silicon steel plates. Sensors and a fault section detector/indicator of a system are connected with optical fibers capable of nonrepeated transmission of over 6 km     

Effect of temperature on the strength and conductivity of a deformation processed Cu-20%Fe composite

The high temperature (22–600 °C) properties were evaluated for a Cu-20%Fe composite deformation processed from a powder metallurgy compact. The ultimate tensile strengths decreased with increasing temperature but were appreciably better than those of similarly processed Cu at temperatures up to 450 °C. At 600 °C, the strength of Cu-20%Fe was only slightly better than that of Cu as a result of the pronounced coarsening of the Fe filaments. However, at temperatures of 300 and 450 °C, the strength of Cu-20%Fe is about seven and six times greater, respectively, than that of Cu, as compared to about a two fold advantage at room temperature. Therefore, Cu-20%Fe composites made by deformation processing of powder metallurgy compacts have mechanical properties much superior to those of similarly processed Cu at room temperature and at temperatures up to 450 °C. The pronounced decrease in electrical conductivity of deformation processed Cu-20%Fe as compared to Cu is attributed to the appreciable dissolution of Fe into the Cu matrix which occurred during the fabrication of the starting compacts where temperatures up to 675 °C were used. While the powder metallurgy compacts used for the starting material for deformation processing in this study did not lead to a high conductivity composite, the powder metallurgy approach should still be a viable one if processing temperatures can be reduced further to prevent the dissolution of Fe into the Cu matrix.     

Soft-decision Viterbi decoding with diversity combining formulti-beam mobile satellite communication systems

Diversity combining methods for mobile satellite communication systems employing convolutional encoding and soft-decision Viterbi decoding are evaluated. Computer simulation clarifies that the pre-Viterbi-decoding maximal ratio combining method has better performance than other methods in Rician fading channels. The simulation results agree with the Pe (bit error probability) performance derived from the numerical analysis for slow fading using the approximate Pe performance of Viterbi decoding in AWGN (additive white Gaussian noise) channels and the probability density function of Rician fading. Applying this diversity method to the multi-beam mobile satellite communication systems, a satellite beam diversity reception scheme is proposed. A computer simulation result shows that the proposed scheme decreases the packet error rate of the control signals to less than 1/100 around the satellite beam boundary     

Complexity of the color appearance of objects with nonuniform illumination

An inversion relationship is clarified between lightness and brightness, and also between chroma and colorfulness under nonuniform illumination with different illuminance levels (high and low) within the same visual field. Brightness (or colorfulness) of object color with low lightness (or chroma) under high illuminance level is perceived higher than that of another object color with high lightness (or chroma) under low illuminance level. Two color images are given for showing the inversion phenomena on brightness–lightness and colorfulness–chroma between object colors under different illuminance levels. These color images are useful for making researchers on color understand the differences in concept between brightness and lightness, and also between colorfulness and chroma. In particular, the concept of colorfulness is important, but difficult to understand. © 2007 Wiley Periodicals, Inc. Col Res Appl, 32, 372–377, 2007