Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

Kernel Spectral Matched Filter for Hyperspectral Imagery

In this paper a kernel-based nonlinear spectral matched filter is introduced for target detection in hyperspectral imagery, which is implemented by using the ideas in kernel-based learning theory. A spectral matched filter is defined in a feature space of high dimensionality, which is implicitly generated by a nonlinear mapping associated with a kernel function. A kernel version of the matched filter is derived by expressing the spectral matched filter in terms of the vector dot products form and replacing each dot product with a kernel function using the so called kernel trick property of the Mercer kernels. The proposed kernel spectral matched filter is equivalent to a nonlinear matched filter in the original input space, which is capable of generating nonlinear decision boundaries. The kernel version of the linear spectral matched filter is implemented and simulation results on hyperspectral imagery show that the kernel spectral matched filter outperforms the conventional linear matched filter.     

Evaluation of Laminated Circular Elastomeric Bearings

This paper evaluates the behavior and performance of laminated circular elastomeric bearings and compares them to those of square and rectangular bearings. The study included an experimental evaluation and a nationwide survey of state Department of Transportations on the use and performance of circular bearings and bearings in general in their states. The experimental investigation studied the bearings' behavior in compression, compression and rotation, and compression and shear. Results from this limited study showed that the three bearings have similar stress-strain behavior in compression and they are in agreement with the AASHTO LRFD guide stress–strain curves. In compression and rotation, the AASHTO LRFD substructure moments are slightly less than the measured values for circular bearings and rectangular bearings rotated about their strong axis for a compressive stress of 10.3?MPa (1.5?ksi) and slightly higher than those of rectangular bearings rotated about their weak axis. In compression and shear, the shear stiffness of circular and square bearings is in agreement with theoretical values within the range of design displacements. Results from the survey showed that many states are using circular bearings and more states would consider using them, however no maintenance or monitoring data were available on their short-term and long-term performance.     

Effect of the percentage carbon equivalent on the nodule characteristics,density and modulus of elasticity of ductile cast iron

Successful melting and Mg treatment were conducted using a vortex unit which produced spheroidal graphite (SG) Fe ingots having a percentage carbon equivalent (%CE) ranging from 3.782 to 5.240. Microstructure examination revealed graphite nodules embedded in a white matrix (unetched condition). The variation of %CE proved to have a pronounced effect on the nodule characteristics. The nodule count showed a maximum value at %CE of 4.613. For metal-mould ingots it reached a value of 1584 nodules mm^–2, while for sand-mould ingots it reached a value of 970 nodules mm^–2. Nodule size was found to be inversely proportional to the nodule count for both sand- and metal-mould ingots. The nodularity of all ingots was, in general, higher than 95%. The density of SG Fe was found to decrease gradually (at %CE=3.782) from 7242 to 6969 kg m^–3. The modulus of elasticity (E) showed a boat-like curve having minimum values of 189 and 192 GPa for the sand and metal moulds, respectively.     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

Analysis and Optimization of Noise in Bipolar RF Harmonic Mixers

A noise analysis of bipolar harmonic mixers (BHM) used for direct-conversion receivers is presented in this paper. Analytical and simulated results for the transfer function of the mixer are presented. Simple analytical expressions describing noise contribution from all sources are derived. Estimation of flicker noise quite agrees with harmonic-balance simulation results. Based on the derived expressions, total time average noise power spectral density (PSD) at the output is compared with simulation results. For the recommended regions of operation, error is less than 20%. The overall BHM noise figure (NF) is calculated and optimized based on a simple extracted formula. Errors introduced by analysis remain within a 1.5-dB margin with respect to simulation results. The validity of analysis for high frequencies is justified. The effect of flicker noise coefficient on the overall mixer NF is compared for different available processes.     

Effect of Reactor Ambient Pressure on the Morphology of Spray Dried Magnesium Sulphate Powders

The effect of reducing the reactor air pressure on the morphology of spray dried magnesium sulphate powders is investigated, experimentally. A reactor, capable of drying and pyrolyzing solution sprays at low pressures, is designed and manufactured. A vibrating mesh nebulizer is employed to generate the spray. Four different pressures, starting from 60 Torr to the atmospheric pressure, and two different reactor air temperatures of 130°C and 420°C, are considered. In addition, two different concentrations of magnesium sulphate solutions are tested. The results are explained based on the effect of reactor air pressure on the droplet evaporation rate.     

A basic program for calculating subsurface water temperatures using chemical geothermometers-implication to geothermal reservoir estimation

GEOTHERM is a computer program written in BASIC language to estimate geothermal reservoir temperature using the well-known chemical gèothermometers. The empirical equations used in the program were obtained from the literature. Three different chemical geothermometers are included in the program: Na-K, Na-K-Ca, and silica geothermometers; this gives the user the opportunity not only to select the most reliable geothermometer in estimating subsurface temperature, but also to select the type of geothermometer according to available data. A sample input file of geothermal waters obtained from Iceland has been tested, so as to show the applicability and usefulness of the program.