FPGA architecture of the LDPS Motion Estimation for H.264/AVC Video Coding

Motion estimation is a highly computational demanding operation during video compression process and significantly affects the output quality of an encoded sequence. Special hardware architectures are required to achieve real-time compression performance. Many fast search block matching motion estimation (BMME) algorithms have been developed in order to minimize search positions and speed up computation but they do not take into account how they can be effectively implemented by hardware. In this paper, we propose three new hardware architectures of fast search block matching motion estimation algorithm using Line Diamond Parallel Search (LDPS) for H.264/AVC video coding system. These architectures use pipeline and parallel processing techniques and present minimum latency, maximum throughput and full utilization of hardware resources. The VHDL code has been tested and can work at high frequency in a Xilinx Virtex-5 FPGA circuit for the three proposed architectures.     

Gettering by heat thermal processing: application in crystalline silicon solar cells

The aim of this work is to getter unwanted impurities from solar grade crystalline silicon (Si) wafers and then to enhance their electronic properties. This was done by forming a sacrificial porous silicon (PS) layer on both sides of the Si wafers and by performing infrared (IR) thermal annealing treatments (at around 950 °C) in a SiCl₄/N₂ controlled atmosphere. The process allows concentrating unwanted impurities in the PS layer and near the PS/silicon interface. These treatments reduce the resistivity by about two orders of magnitude at a depth of about 40 μm and improve the minority carrier diffusion length from 75 to 210 μm. This gettering method was also tested on silicon wafers where grooved fingers and back contacts were achieved using a chemical vapor etching (CVE) method. Front buried metallic contacts and small holes for local back surface field were then achieved after the gettering stage in order to realize silicon solar cells. It was shown that the photovoltaic parameters of gettered silicon solar cells were improved as regard to ungettered ones.     

Analysis of a new annular multi-slits antenna using wave concept iterative process in cylindrical coordinates

In this paper, a new antenna for satellite applications is proposed. This antenna is designed to operate at any frequency desired. It consists of a circular microstrip patch antenna which incorporates concentric annular slits, and it is printed on a grounded substrate. The details of the proposed antenna design and numerical results are presented and discussed. The wave concept iterative procedure in cylindrical coordinates is used to analyze this new antenna. Using the proposed procedure, less computing time and memory are needed to calculate the electromagnetic parameters of the annular multi-slits antenna.     

Dielectric properties of new fully conjugated 2H‐ and metal‐pyrazinoporphyrazine network polymers

2,7‐Di‐tert‐butylpyrene was oxidized to 2,7‐di‐tert‐butylpyrene‐4,5,9,10‐tetraone. The latter through condensation reaction with vicinal diamine such as diaminomaleodinitrile afforded heterocyclic monomer, 2,7‐di‐tert‐butyl pyrene[4,5][9,10]bis(2,3‐pyrazine‐5,6‐dinitrile), which was cyclotetramerized to the corresponding 2H‐ and metal‐pyrazinoporphyrazine‐based network polymers (2H‐PyzPz and M‐PyzPz, M = Co, Ni, Zn, or Cu). Elemental analytical results, Infrared, and NMR spectral data of the new prepared molecules are consistent with their assigned formulations. Molecular masses and metal contents of the synthesized polymers proved to be of high molecular masses, which confirm the efficiency of tetramerization polymerization and complexation reactions. Dielectric permittivity, ε′, loss tangent, tan δ, and ac conductivity, σac(ω), of 2H‐PyzPz and M‐PyzPz films were studied as a function of temperature and frequency. It was found that dielectric permittivity, ε′, decreases with the increase of frequency and increases with the increase in temperature. Ac conductivity, σac(ω), is found to vary as Bωs and the frequency exponent, s, is less than unity around room temperature indicating a dominant hopping process. On the other hand, σac(T) of all samples is thermally activated with low activation energies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Investigation of Heat‐Induced Degradation of Virgin Olive Oil Using Front Face Fluorescence Spectroscopy and Chemometric Analysis

A simple setup using a 365‐nm light‐emitting diode coupled to a USB spectrometer through an optical fiber, in a front‐face fluorescence configuration, was used to investigate the heat‐induced deterioration of virgin olive oil at different heating temperatures and times. The samples were heated for 30, 60, 120 and 180 min for every temperature setting of 140, 160 and 180 °C, respectively. Two important results are reported in this article. First, a neo‐formed compound around 665 nm due to the degradation of chlorophyll was observed. This new peak was attributed to pyropheophytins. The second result showed an important rise of the peak around 489 nm, which corresponded to the oxidation products. The correlation obtained between the peroxide value and the 489 nm peak using principal component analysis revealed the mechanism of the oxidation process. It further showed that the peak around 489 nm is a direct consequence of the degradation of hydroperoxide.     

Influence of moisture content on the specific methanogenic activity of dry mesophilic municipal solid waste digestate

The objective of this study was to evaluate the influence of moisture content on the specific methanogenic activity (SMA) of a fresh dry mesophilic digestate from a municipal solid waste digester plant. For this purpose, SMA tests were performed under mesophilic conditions in 500 mL glass bottles of volume used as batch reactors, during a period of 20–25 days. Cellulose, propionate and acetate were used as substrates (5 g_COD kg^?1 digestate) at four different moisture contents, ranging from 65 to 82%. The moisture content strongly influenced the specific methanogenic activity. The highest SMA values were observed at a moisture content of 82% (11.1, 7.8 and 6.0 mg_COD g_VS^?1 d^?1 for cellulose, propionate and acetate spikes, respectively). SMA and moisture content were found to be linearly linked. Dry digestion at low water content is thus detrimental to the biological activity, probably due to physical limitations. Copyright © 2011 Society of Chemical Industry     

Rheological behavior of neat and carbon fiber-reinforced poly(ether ketone ketone) for extrusion deposition additive manufacturing

To develop new materials for extrusion additive manufacturing (AM) systems, a fundamental understanding of rheological properties is essential to correlate the effect of processing on material structure and its properties. In this work, the rheological properties of five different grades of neat and carbon fiber (CF)-reinforced poly(ether ketone ketone) are reported. Rheological properties are essential to understand the effect of reinforcing fibers and AM process parameters such as time, temperature, environment, and shear rate on flow behavior during processing. Small-amplitude oscillatory shear tests and steady shear tests indicated neat grades to exhibit less increase in viscosity over time when processed in air than the CF-filled grades. The filled grades showed greater shear thinning and lower sensitivity to temperature. Overall, this rheological analysis provides a broad framework for determining appropriate processing conditions for extrusion deposition AM of such high-temperature polymer systems.     

Increased Emulsion Stability for Reverse Y‐Shaped Sugar‐Based Surfactants

A series of reverse Y‐shaped surfactants containing aromatic and aliphatic linkers to combine two short hydrocarbon chains and one carbohydrate head group was prepared. Liquid crystalline behavior, air–water interfacial properties, and efficiency as an emulsifier was investigated for each reverse Y‐shaped surfactant. All reverse Y‐shaped surfactants mediated higher emulsion stabilities for water‐in‐oil compared to common typical reference surfactants, reflecting an improved ability to cope with a curvature towards water. The introduction of a benzene ring into the linker substantially increased the affinity of the surfactant for hydrophobic media, resulting in improved emulsion stability for both water‐in‐oil and oil‐in‐water.     

Nanovesicles Based on Mixtures of a Biantennary Glycolipid with Ionic Co‐Surfactants

A biantennary surfactant based on a synthetic C₁₆‐maltoside was chosen to prepare vesicles for a potential vesicular drug delivery system. The synthesis comprised of three stages: Initial synthesis of β‐d ‐maltose octaacetate was followed by glycosidation of 2‐hexyl‐decanol and final glycolipid deacetylation. Both α‐ and β‐anomers were prepared and their anomeric purity was evaluated by ¹H NMR. Owing to the low water solubility of the glycolipid, addition of ionic co‐surfactants was believed to promote the surfactant distribution, thus leading to smaller and more uniform vesicles. The assembly behavior of the surfactant systems was studied by contact penetration under an optical polarizing microscope, while interfacial properties were determined by surface tension measurements. Vesicles were prepared by injection of an ethanolic solution into bulk water and investigated by dynamic light scattering and field emission scanning electron microscopy. Contact of the surfactant mixtures with water indicated a high tendency to exhibit the lamellar phase and confirmed the expected low molecular solubility. These findings suggest a potential of the surfactant to form stable vesicles. Injection of an ethanolic surfactant solution into bulk water gave sub‐micrometer sized vesicles with a narrow size distribution. Application of ionic co‐surfactants reduced the vesicle size. In particular ～20 % of anionic SDS proved highly effective, lowering the vesicle size by nearly one decade, thus accessing nano‐sized vesicles. Encapsulation of a water‐soluble drug was achieved in a 76 ± 10 % efficiency.