Effect of cellulose acetate/cellulose triacetate ratio on reverse osmosis blend membrane performance

Surface functionalization and modification including the grafting process are effective approaches to improve and enhance the reverse osmosis (RO) membrane performance. This work is aimed to synthesize grafted/crosslinked cellulose acetate (CA)/cellulose triacetate (CTA) blend RO membranes using N-isopropylacrylamide (N-IPAAm) as a monomer and N,N-methylene bisacrylamide (MBAAm) as a crosslinker. The morphology of these membranes was analyzed by scanning electron microscopy and their surface roughness was characterized by atomic force microscopy. The performance of these membranes was evaluated through measuring two major parameters of salt rejection and water flux using RO unit at variable operating pressures. It was noted that the surface average roughness obviously decreased from 148 nm for the pure CA/CTA blend membrane with 2.5% CTA to 110 nm and 87 nm for the grafted N-IPAAm and grafted/crosslinked N-IPAAM/MBAAm/CA/CTA-RO membranes, respectively. Moreover, the contact angle decreased from 51.98° to 47.6° and 43.8° after the grafting and crosslinking process. The salt rejection of the grafted CA/CTA-RO membrane by 0.1% N-IPAAm produced the highest value of 98.12% and the water flux was 3.29 L/m²h at 10 bar.     

The Impact of PbF2-Based Glasses on Radiation Shielding and Mechanical Concepts: An Extensive Theoretical and Monte Carlo Simulation Study

Journal of Inorganic and Organometallic Polymers and Materials - This work aimed to investigate the impact of Lead-fluoride based glasses via theoretical and simulation techniques on mechanical and...     

Pheromone Disruption of Argentine Ant Trail Integrity

Disruption of Argentine ant trail following and reduced ability to forage (measured by bait location success) was achieved after presentation of an oversupply of trail pheromone, (Z)-9-hexadecenal. Experiments tested single pheromone point sources and dispersion of a formulation in small field plots. Ant walking behavior was recorded and digitized by using video tracking, before and after presentation of trail pheromone. Ants showed changes in three parameters within seconds of treatment: (1) Ants on trails normally showed a unimodal frequency distribution of walking track angles, but this pattern disappeared after presentation of the trail pheromone; (2) ants showed initial high trail integrity on a range of untreated substrates from painted walls to wooden or concrete floors, but this was significantly reduced following presentation of a point source of pheromone; (3) the number of ants in the pheromone-treated area increased over time, as recruitment apparently exceeded departures. To test trail disruption in small outdoor plots, the trail pheromone was formulated with carnuba wax-coated quartz laboratory sand (1 g quartz sand/0.2 g wax/1 mg pheromone). The pheromone formulation, with a half-life of 30 h, was applied by rotary spreader at four rates (0, 2.5, 7.5, and 25 mg pheromone/m²) to 1- and 4-m² plots in Volcanoes National Park, Hawaii. Ant counts at bait cards in treated plots were significantly reduced compared to controls on the day of treatment, and there was a significant reduction in ant foraging for 2 days. These results show that trail pheromone disruption of Argentine ants is possible, but a much more durable formulation is needed before nest-level impacts can be expected. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Transition to turbulence in rotating-disk boundary layers—convective and absolute instabilities

This work is an experimental study of mechanisms for transition to turbulence in the boundary layer on a rotating disk. In one case, the focus was on a triad resonance between pairs of traveling cross-flow modes and a stationary cross-flow mode. The other was on the temporal growth of traveling modes through a linear absolute instability mechanism first discovered by Lingwood (1995, J Fluid Mech 314:373–405). Both research directions made use of methods for introducing controlled initial disturbances. One used a distributed array of ink dots placed on the disk surface to enhance a narrow band of azimuthal and radial wave numbers of both stationary and traveling modes. The size of the dots was small so that the disturbances they produce were linear. Another approach introduced temporal disturbances by a short-duration air pulse from a hypodermic tube located above the disk and outside the boundary layer. Hot-wire sensors primarily sensitive to the azimuthal velocity component, were positioned at different spatial (r,θ) locations on the disk to document the growth of disturbances. Spatial correlation measurements were used with two simultaneous sensors to obtain wavenumber vectors. Cross-bicoherence was used to identify three-frequency phase locking. Ensemble averages conditioned on the air pulses revealed wave packets that evolved in time and space. The space–time evolution of the leading and trailing edges of the wave packets were followed past the critical radius for the absolute instability, r _{c A} . With documented linear amplitudes, the spreading of the disturbance wave packets did not continue to grow in time as r _{c A} was approached. Rather, the spreading of the trailing edge of the wave packet decelerated and asymptotically approached a constant. This result supports the linear DNS simulations of Davies and Carpenter (2003, J Fluid Mech 486:287–329) who concluded that the absolute instability mechanism does not result in a global mode, and that linear-disturbance wave packets are dominated by the convective instability. In contrast, wave-number matching between traveling cross-flow modes confirmed a triad resonance that lead to the growth of a low azimuthal number (n = 4) stationary mode. At transition, this mode had the largest amplitude. Signs of this mechanism can be found in past flow visualization of transition to turbulence in rotating disk flows.     

Postintegration methods for numerical integration of non-linear dynamic equations of motion

The paper presents a family of methods with postintegration, for numerical integration of non-linear dynamic equations of motion of discrete systems. Both explicit and implicit algorithms of these methods are conditionally stable, but can give solutions of accuracy of a few orders higher than the known methods with preintegration, corresponding to them. A general analysis of stability and accuracy of single-step methods is carried out. The postintegration methods have been tested on a single-degree-of-freedom non-linear system.     

Comments on “Distinguishability quantification of fuzzy sets”

This paper presents some comments on the above paper regarding the manipulation of Gaussian fuzzy sets and provides two useful generalized formulas for both of similarity and similarity/possibility relationships of Gaussian fuzzy sets with different widths.     

Comparison of two different approaches for making design sensitivity analysis an integrated part of finite element analysis

This paper presents a comparison of two approaches for incorporating design sensitivity calculations into finite element analysis. The formulations depend on the implicit differentiation method and require few additional calculations to obtain the design sensitivity derivatives. The first approach by-passes the direct calculation of the stiffness matrix derivatives by calculating the sensitivity derivatives at the stress recovery stage of the analysis. The second approach depends on the direct calculation of the derivatives of the stiffness matrix, which are stored for re-use in multiple load case analyses, and subsequent matrix multiplications to evaluate the design sensitivities. The two approaches are developed and implemented to calculate the design sensitivities for continuum and structural isoparametric elements. In addition, a criterion is developed to aid in deciding which approach is better for a given number of load cases. To demonstrate the validity of the developed criterion and to evaluate the relative merits of each approach, some sensitivity calculation test problems are solved with different numbers of load cases.     

Combustion synthesis of NbC/ZrO2 composites: Influence of Cr additives on the microstructure and mechanical properties

Composites of NbC/ZrO₂ reinforced with different weight ratios of Cr metal were prepared by dynamic compaction combustion from a blend of Nb₂O₅–Zr–Cr powders. Factors controlling the synthesis process, the microstructure, and the mechanical properties of the samples, such as Cr wt% and the compression loads were studied. The samples were characterized by XRD, SEM, porosity, and hardness measurements. The porosity value of the sample with no additives was high and reached 31.6 vol%. A sudden decrease in the sample porosity to 2.4 vol % was noticed for the sample containing 3.0 wt% of Cr. A high-density sample with less than 2.0 vol % porosity and maximum hardness of 1038 HV was produced using 5.0 wt% Cr under 300 MPa compression load. Detailed thermodynamic calculations for the effect of Cr additives on the physicochemical properties of the system were introduced.     

The Impact of Metastable Intermolrecular Nanocomposite Particles on Kinetic Decomposition of Heterocyclic Nitramines Using Advanced Solid‐Phase Decomposition Models

Journal of Inorganic and Organometallic Polymers and Materials - Surface oxygen of oxide catalyst has low coordination number; they are negatively charged. Surface oxygen can act active site for...     

Some interesting properties of metals confined in time and nanometer space of different shapes

The properties of a material depend on the type of motion its electrons can execute, which depends on the space available for them (i.e., on the degree of their spatial confinement). Thus, the properties of each material are characterized by a specific length scale, usually on the nanometer dimension. If the physical size of the material is reduced below this length scale, its properties change and become sensitive to its size and shape. In this Account we describe some of the observed new chemical, optical, and thermal properties of metallic nanocrystals when their size is confined to the nanometer length scale and their dynamical processes are observed on the femto- to picosecond time scale.